| # This file - Makefile.base-vars - together with the file Makefile.base-rules, |
| # make up a reusable buildsystem for DocBook XML books. |
| # The split into two files is required because of the nature of Make variables: |
| # In the case of variables used in commands, expansion occurs when the commands |
| # are executed, so values can be overridden by defining a new value after the |
| # rule definition - BUT in the case of variables used to specify targets and |
| # sources, expansion occurs when Make parses the rule. Therefore, any override |
| # must take place BEFORE the rule definition. Since this Makefile fragment |
| # wishes to both provide defaults and allow overriding of target and source |
| # file names, it is necessary to place the default variable definitions in |
| # one file, and the rules in another, so that overrides may be specified |
| # after the defaults, but before the rules - like this: |
| # |
| # include ../tools/Makefile.base-vars |
| # NAME = my-book |
| # DIR = my-book-dir |
| # include ../tools/Makefile.base-rules |
| # |
| # Note that this is a Makefile fragment intended for inclusion. As a result, |
| # all relative paths contained within are relative to including Makefile's |
| # directory, not to this fragment's directory. The TOOLS_DIR and DIR variables |
| # should be overridden if necessary to ensure proper paths are used. |
| |
| # Paths which you may wish to customize: |
| XSLTPROC = xsltproc |
| XMLLINT = xmllint |
| INSTALL_DIR = $(DESTDIR)/usr/share/doc/OVERRIDE_ME_WITH_SOMETHING_SUITABLE |
| INSTALL_DATA = cp -r |
| MKDIR = mkdir -p |
| SVNVERSION = svnversion |
| |
| # You should not normally need to edit anything below here. |
| SHELL = /bin/sh |
| |
| NAME = OVERRIDE_ME_WITH_THE_SHORT_FILESYSTEM_NAME_OF_YOUR_BOOK |
| DIR = . |
| IMAGES = |
| TOOLS_DIR = ../tools |
| OUTNAME = $(NAME) |
| |
| HTML_CHUNK_DIR = $(DIR)/html-chunk |
| HTML_TARGET = $(DIR)/$(OUTNAME).html |
| # In the HTML chunk build, index.html is created last, so serves as an |
| # acceptable timestamp file for the entire multi-file output. |
| HTML_CHUNK_TARGET = $(HTML_CHUNK_DIR)/index.html |
| ARCH_CMD = tar -jcvf |
| ARCH_EXT = .tar.bz2 |
| HTML_ARCH_BASENAME = $(OUTNAME)-html |
| HTML_CHUNK_ARCH_BASENAME = $(OUTNAME)-html-chunk |
| HTML_ARCH_TARGET = $(DIR)/$(HTML_ARCH_BASENAME)$(ARCH_EXT) |
| HTML_CHUNK_ARCH_TARGET = $(DIR)/$(HTML_CHUNK_ARCH_BASENAME)$(ARCH_EXT) |
| PDF_TARGET = $(DIR)/$(OUTNAME).pdf |
| PS_TARGET = $(DIR)/$(OUTNAME).ps |
| FO_TARGET = $(DIR)/$(OUTNAME).fo |
| XML_SOURCE = $(DIR)/$(NAME).xml |
| VERSION_SOURCE = $(DIR)/version.xml |
| ALL_SOURCE = $(DIR)/*.xml |
| STYLESHEET = $(DIR)/styles.css |
| INSTALL_SUBDIR = $(INSTALL_DIR)/$(NAME) |
| |
| ENSURE_XSL = if ! test -e "$(TOOLS_DIR)/xsl"; \ |
| then $(TOOLS_DIR)/bin/find-xsl.py; fi |
| IFIMAGES = if test -n "$(IMAGES)"; then |
| ENDIF = ; fi |
| |
| # Customization hooks for xsltproc options |
| HTML_XSLTPROC_OPTS = |
| FO_XSLTPROC_OPTS = |
| # FO example: --stringparam page.height 9in --stringparam page.width 6.4in |
| |
| # Uncomment the following line if you'd like to print on A4 paper |
| # FO_XSLTPROC_OPTS = --stringparam paper.type A4 |
| |
| # Override in locale-specific Makefile to localize the word in the |
| # auto-generated version file. |
| L10N_REVISION = Revision |
