Google Git
Sign in
apache / nuttx / refs/heads/revert-17300-apache_6 / . / boards / arm / stm32 / stm32f103-minimum / src / stm32f103_minimum.h
blob: e2d4d3837c08f49af61df5349a05555b0dfc6efe [file] [log] [blame]
/****************************************************************************
* boards/arm/stm32/stm32f103-minimum/src/stm32f103_minimum.h
*
* SPDX-License-Identifier: Apache-2.0
*
* Licensed to the Apache Software Foundation (ASF) under one or more
* contributor license agreements. See the NOTICE file distributed with
* this work for additional information regarding copyright ownership. The
* ASF licenses this file to you under the Apache License, Version 2.0 (the
* "License"); you may not use this file except in compliance with the
* License. You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
* License for the specific language governing permissions and limitations
* under the License.
*
****************************************************************************/
#ifndef __BOARDS_ARM_STM32_STM32F103_MINIMUM_SRC_STM32F103_MINIMUM_H
#define __BOARDS_ARM_STM32_STM32F103_MINIMUM_SRC_STM32F103_MINIMUM_H
/****************************************************************************
* Included Files
****************************************************************************/
#include <nuttx/config.h>
#include <nuttx/compiler.h>
#include <stdint.h>
#include <arch/chip/chip.h>
/****************************************************************************
* Pre-processor Definitions
****************************************************************************/
#define HAVE_AT24 1
/* AT24 Serial EEPROM */
#define AT24_I2C_BUS 1 /* AT24C256 connected to I2C1 */
#define AT24_MINOR 0
#if !defined(CONFIG_MTD_AT24XX) || !defined(CONFIG_STM32_I2C1)
# undef HAVE_AT24
#endif
/* Can't support AT24 features if mountpoints are disabled or if we were not
* asked to mount the AT25 part
*/
#if defined(CONFIG_DISABLE_MOUNTPOINT) || \
!defined(CONFIG_STM32F103MINIMUM_AT24_BLOCKMOUNT)
# undef HAVE_AT24
#endif
/* procfs File System */
#ifdef CONFIG_FS_PROCFS
# ifdef CONFIG_NSH_PROC_MOUNTPOINT
# define STM32_PROCFS_MOUNTPOINT CONFIG_NSH_PROC_MOUNTPOINT
# else
# define STM32_PROCFS_MOUNTPOINT "/proc"
# endif
#endif
/* If we are going to mount the AT24, then they user must also have told
* us what to do with it by setting one of these.
*/
#ifndef CONFIG_FS_NXFFS
# undef CONFIG_STM32F103MINIMUM_AT24_NXFFS
#endif
#if !defined(CONFIG_STM32F103MINIMUM_AT24_FTL) && \
!defined(CONFIG_STM32F103MINIMUM_AT24_NXFFS)
# undef HAVE_AT24
#endif
/* How many SPI modules does this chip support? The LM3S6918 supports 2 SPI
* modules (others may support more -- in such case, the following must be
* expanded).
*/
#if STM32_NSPI < 1
# undef CONFIG_STM32_SPI1
# undef CONFIG_STM32_SPI2
#elif STM32_NSPI < 2
# undef CONFIG_STM32_SPI2
#endif
/* GPIOs ********************************************************************/
/* LEDs */
/* The Blue/Red pills have a different pinout to the Black pill,
* which includes the board's user LED.
*/
#ifdef CONFIG_STM32F103MINIMUM_BLACKPILL
# define GPIO_LED1 (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_CLEAR|GPIO_PORTB|GPIO_PIN12)
#else
# define GPIO_LED1 (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_CLEAR|GPIO_PORTC|GPIO_PIN13)
#endif
/* BUTTONs */
#define GPIO_BTN_USER1 (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_MODE_INPUT|\
GPIO_EXTI|GPIO_PORTA|GPIO_PIN0)
#define GPIO_BTN_USER2 (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_MODE_INPUT|\
GPIO_EXTI|GPIO_PORTA|GPIO_PIN1)
#define MIN_IRQBUTTON BUTTON_USER1
#define MAX_IRQBUTTON BUTTON_USER2
#define NUM_IRQBUTTONS (BUTTON_USER1 - BUTTON_USER2 + 1)
/* SPI chip selects */
#define FLASH_SPI1_CS (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTA|GPIO_PIN4)
#define GPIO_CS_MFRC522 (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTA|GPIO_PIN4)
#define STM32_LCD_CS (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTA|GPIO_PIN4)
#define GPIO_MAX6675_CS (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTA|GPIO_PIN4)
#define GPIO_MCP2515_CS (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTA|GPIO_PIN4)
#define GPIO_NRF24L01_CS (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTA|GPIO_PIN4)
#define GPIO_SDCARD_CS (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTA|GPIO_PIN4)
#define STM32_LCD_RST (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTA|GPIO_PIN3)
#define STM32_LCD_RS (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTA|GPIO_PIN2)
#define STM32_LCD_CD (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTA|GPIO_PIN2)
/* PWM Configuration */
#define STM32F103MINIMUM_PWMTIMER 3
#define STM32F103MINIMUM_PWMCHANNEL 3
/* LM-75 Temperature Sensor: PA.0 */
#define GPIO_LM75_OSINT (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_PORTA|GPIO_PIN0)
/* nRF24 Configuration */
/* MCP2515 IRQ line: PB.0 */
#define GPIO_MCP2515_IRQ (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_PORTB|GPIO_PIN0)
/* USB Soft Connect Pullup: PC.13 */
#define GPIO_USB_PULLUP (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTA|GPIO_PIN12)
/* GPIO pins used by the GPIO Subsystem */
#define BOARD_NGPIOIN 1 /* Amount of GPIO Input pins */
#define BOARD_NGPIOOUT 1 /* Amount of GPIO Output pins */
#define BOARD_NGPIOINT 1 /* Amount of GPIO Input w/ Interruption pins */
#define GPIO_IN1 (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_PORTA|GPIO_PIN0)
#define GPIO_OUT1 (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz|\
GPIO_OUTPUT_SET|GPIO_PORTA|GPIO_PIN1)
#define GPIO_INT1 (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_PORTA|GPIO_PIN2)
/* WS2812 LEDs */
#define WS2812_NLEDS 2
#define WS2812_SPI 1
/* Sensor */
#define BOARD_HYT271_NBUS 2 /* Bus number of connected HYT271 */
#define BOARD_HYT271_POWOUT (GPIO_OUTPUT|GPIO_CNF_OUTPP|GPIO_MODE_50MHz| \
GPIO_OUTPUT_SET|GPIO_PORTA|GPIO_PIN0)
#define BOARD_HYT271_POWIN (GPIO_INPUT|GPIO_CNF_INFLOAT|GPIO_PORTA| \
GPIO_PIN1)
#define BOARD_DS18B20_NBUS 2 /* Bus number of connected DS18B20 */
#define BOARD_DS18B20_NSLAVES 2 /* Number of expected DS18B20 slaves */
/****************************************************************************
* Public Function Prototypes
****************************************************************************/
#ifndef __ASSEMBLY__
/****************************************************************************
* Name: stm32_bringup
*
* Description:
* Perform architecture specific initialization
*
* CONFIG_BOARDCTL=y:
* If CONFIG_NSH_ARCHINITIALIZE=y:
* Called from the NSH library (or other application)
* Otherwise, assumed to be called from some other application.
*
* Otherwise CONFIG_BOARD_LATE_INITIALIZE=y:
* Called from board_late_initialize().
*
* Otherwise, bad news: Never called
*
****************************************************************************/
int stm32_bringup(void);
/****************************************************************************
* Name: stm32_gpio_initialize
*
* Description:
* Initialize GPIO drivers for use with /apps/examples/gpio
*
****************************************************************************/
#ifdef CONFIG_DEV_GPIO
int stm32_gpio_initialize(void);
#endif
/****************************************************************************
* Name: stm32_adc_setup
*
* Description:
* Initialize ADC and register the ADC driver.
*
****************************************************************************/
#ifdef CONFIG_ADC
int stm32_adc_setup(void);
#endif
/****************************************************************************
* Name: stm32_spidev_initialize
*
* Description:
* Called to configure SPI chip select GPIO pins for the Hy-Mini STM32v
* board.
*
****************************************************************************/
void stm32_spidev_initialize(void);
/****************************************************************************
* Name: stm32_mmcsd_initialize
*
* Description:
* Initializes SPI-based SD card
*
****************************************************************************/
#ifdef CONFIG_MMCSD
int stm32_mmcsd_initialize(int minor);
#endif
/****************************************************************************
* Name: stm32_w25initialize
*
* Description:
* Called to initialize Winbond W25 memory
*
****************************************************************************/
int stm32_w25initialize(int minor);
/****************************************************************************
* Name: stm32_rgbled_setup
*
* Description:
* This function is called by board initialization logic to configure the
* RGB LED driver. This function will register the driver as /dev/rgbled0.
*
* Input Parameters:
* None
*
* Returned Value:
* Zero is returned on success. Otherwise, a negated errno value is
* returned to indicate the nature of the failure.
*
****************************************************************************/
#ifdef CONFIG_RGBLED
int stm32_rgbled_setup(void);
#endif
/****************************************************************************
* Name: stm32_mcp2515initialize
*
* Description:
* Initialize and register the MCP2515 CAN driver.
*
****************************************************************************/
#ifdef CONFIG_CAN_MCP2515
int stm32_mcp2515initialize(const char *devpath);
#endif
/****************************************************************************
* Name: stm32_usbinitialize
*
* Description:
* Called to setup USB-related GPIO pins for the Hy-Mini STM32v board.
*
****************************************************************************/
void stm32_usbinitialize(void);
/****************************************************************************
* Name: stm32_pwm_setup
*
* Description:
* Initialize PWM and register the PWM device.
*
****************************************************************************/
#ifdef CONFIG_PWM
int stm32_pwm_setup(void);
#endif
/****************************************************************************
* Name: stm32_hyt271initialize
*
* Description:
* Function used to initialize HYT271 snesors on a i2c bus
*
* Parameter:
* devno - First character device number
*
* Return
* Error or number of device that have been successfully registered.
*
****************************************************************************/
#ifdef CONFIG_SENSORS_HYT271
int stm32_hyt271initialize(int devno);
#endif
/****************************************************************************
* Name: stm32_ds18b20initialize
*
* Description:
* Function used to initialize DS18B20 snesors on a 1wire bus
*
* Parameter:
* devno - First character device number
*
* Return
* Error or number of device that have been successfully registered.
*
****************************************************************************/
#ifdef CONFIG_SENSORS_DS18B20
int stm32_ds18b20initialize(int devno);
#endif
#endif /* __ASSEMBLY__ */
#endif /* __BOARDS_ARM_STM32_STM32F103_MINIMUM_SRC_STM32F103_MINIMUM_H */