drivers/wireless/Kconfig

#
# For a description of the syntax of this configuration file,
# see the file kconfig-language.txt in the NuttX tools repository.
#

menuconfig DRIVERS_WIRELESS
	bool "Wireless Device Support"
	default n
	---help---
		Drivers for various wireless devices.

if DRIVERS_WIRELESS

config WL_CC1101
	bool "CC1101 RF transceiver support"
	default n
	select SPI
	select SCHED_HPWORK

if WL_CC1101

config CC1101_SPIDEV
	int "SPI bus number"
	default 2
	---help---
		Selects the SPI bus number identifying that SPI interface that
		connects the CC1101 to the MCU.

config CC1101_SPIFREQ_BURST
	int "SPI burst frequency"
	default 6500000
	---help---
		SPI burst frequency (Hz, no delay) for CC1101.

config CC1101_SPIFREQ_SINGLE
	int "SPI single access frequency"
	default 9000000
	---help---
		SPI single access frequency (Hz, single access only - no delay) for CC1101.

endif

config WL_CC1101_IGNORE_VERSION
	bool "Ignore CC1101 Version Check (Allow Clone Chips)"
	default n
	depends on WL_CC1101
	---help---
		Some third-party CC1101 clone silicon hardcodes the VERSION
		register to 0x00. Enabling this option bypasses the strict
		version verification, allowing these compatible chips to
		initialize.

		Warning: Enabling this may cause false-positives if the SPI
		MISO line is shorted to GND.

config WL_GS2200M
	bool "Telit GS2200M Wi-Fi support"
	default n
	select SPI
	select LIBC_SCANSET
	select SCHED_LPWORK
	select DRIVERS_IEEE80211
	select NFS_DONT_BIND_TCP_SOCKET if NFS && NET_TCP

if WL_GS2200M

config WL_GS2200M_ENABLE_WEP
	bool "WEP support in AP mode"
	default false

config WL_GS2200M_SPI_FREQUENCY
	int "SPI frequency for GS2200M"
	default 4000000
	range 4000000 10000000

config WL_GS2200M_DISABLE_DHCPC
	bool "Disable the internal dhcp client"
	default n

config WL_GS2200M_CHECK_VERSION
	bool "Check the version of GS2200M"
	default n

config WL_GS2200M_SYNC_INTERVAL
	int "Sync loss interval in station mode (100ms)"
	default 100
	range 1 63325
	---help---
		Time interval to recognize dis-association situation.
		The value indicate n times of Wi-Fi beacon. If the node
		lost receiving beacon n times, behave as dis-associtaion.
		Time difference between 2 beacons are approximately 100 msec.
		So the unit of the value is 100 ms.

config WL_GS2200M_LOGLEVEL
	int "Log level"
	default 0
	range 0 2
	---help---
		The debug level of GS2200M. (AT+LOGLVL)

endif

source "drivers/wireless/spirit/Kconfig"

menuconfig DRIVERS_IEEE802154
	bool "IEEE 802.15.4 Device Support"
	default n
	---help---
		Select to enable building of IEEE802.15.4 device drivers.

source "drivers/wireless/ieee802154/Kconfig"

menuconfig DRIVERS_IEEE80211
	bool "IEEE 802.11 Device Support"
	default n
	---help---
		Select to enable building of IEEE802.11 device drivers.

source "drivers/wireless/ieee80211/Kconfig"

menuconfig DRIVERS_BLUETOOTH
	bool "Bluetooth Device Support"
	default n
	---help---
		Select to enable building of Bluetooth device drivers.

source "drivers/wireless/bluetooth/Kconfig"

menuconfig DRIVERS_LPWAN
	bool "LPWAN Device Support"
	default n
	---help---
		Select to enable building of LPWAN device drivers.

source "drivers/wireless/lpwan/Kconfig"

config WL_NRF24L01
	bool "nRF24l01+ transceiver support"
	default n
	select SPI
	---help---
		This options adds driver support for the Nordic nRF24L01+ chip.

if WL_NRF24L01

config WL_NRF24L01_DFLT_ADDR_WIDTH
	int "Default address width"
	default 5
	range 3 5
	---help---
		Default address width to be used by the nRF24l01+ driver.
		Note that this default can be changed through the driver API.

config WL_NRF24L01_CHECK_PARAMS
	bool "Check call parameters"
	default y
	---help---
		This option adds some sanity check code to parameters given in the
		driver API functions. If this option is disabled, parameter
		values are passed 'as is' to the module hardware registers.

config WL_NRF24L01_RXSUPPORT
	bool "Support messages reception"
	default y
	---help---
		If this option is disabled the driver supports only the transmission of messages.
		Reception of messages will be disabled (and corresponding functions removed).
		Note: this option is intended to reduce driver code size for 'transmission
		only' devices.

if WL_NRF24L01_RXSUPPORT

config WL_NRF24L01_RXFIFO_LEN
	int "RX fifo length"
	default 128
	range 34 2048
	---help---
		Length of the software based fifo used to store content of
		received messages.

endif # WL_NRF24L01_RXSUPPORT
endif # WL_NRF24L01

endif # DRIVERS_WIRELESS