| # |
| # For a description of the syntax of this configuration file, |
| # see the file kconfig-language.txt in the NuttX tools repository. |
| # |
| |
| comment "Tiva/Stellaris Configuration Options" |
| |
| choice |
| prompt "Tiva/Stellaris Chip Selection" |
| default ARCH_CHIP_LM3S6965 |
| depends on ARCH_CHIP_LM || ARCH_CHIP_TIVA || ARCH_CHIP_SIMPLELINK |
| |
| config ARCH_CHIP_LM3S6918 |
| bool "LM3S6918" |
| depends on ARCH_CHIP_LM |
| select ARCH_CORTEXM3 |
| select ARCH_CHIP_LM3S |
| select TIVA_HAVE_I2C1 |
| select TIVA_HAVE_SSI1 |
| select TIVA_HAVE_TIMER3 |
| select TIVA_HAVE_ETHERNET |
| |
| config ARCH_CHIP_LM3S9B92 |
| bool "LM3S9B92" |
| depends on ARCH_CHIP_LM |
| select ARCH_CORTEXM3 |
| select ARCH_CHIP_LM3S |
| select TIVA_HAVE_UART3 |
| select TIVA_HAVE_I2C1 |
| select TIVA_HAVE_SSI1 |
| select TIVA_HAVE_TIMER3 |
| select TIVA_HAVE_ETHERNET |
| select TIVA_HAVE_GPIOH_IRQS |
| |
| config ARCH_CHIP_LM3S9B96 |
| bool "LM3S9B96" |
| depends on ARCH_CHIP_LM |
| select ARCH_CORTEXM3 |
| select ARCH_CHIP_LM3S |
| select TIVA_HAVE_UART3 |
| select TIVA_HAVE_I2C1 |
| select TIVA_HAVE_SSI1 |
| select TIVA_HAVE_TIMER3 |
| select TIVA_HAVE_ETHERNET |
| select TIVA_HAVE_GPIOH_IRQS |
| |
| config ARCH_CHIP_LM3S6432 |
| bool "LM3S6432" |
| depends on ARCH_CHIP_LM |
| select ARCH_CORTEXM3 |
| select ARCH_CHIP_LM3S |
| select TIVA_HAVE_ETHERNET |
| |
| config ARCH_CHIP_LM3S6965 |
| bool "LM3S6965" |
| depends on ARCH_CHIP_LM |
| select ARCH_CORTEXM3 |
| select ARCH_CHIP_LM3S |
| select TIVA_HAVE_UART3 |
| select TIVA_HAVE_I2C1 |
| select TIVA_HAVE_TIMER3 |
| select TIVA_HAVE_ETHERNET |
| select TIVA_HAVE_GPIOH_IRQS |
| |
| config ARCH_CHIP_LM3S8962 |
| bool "LM3S8962" |
| depends on ARCH_CHIP_LM |
| select ARCH_CORTEXM3 |
| select ARCH_CHIP_LM3S |
| select TIVA_HAVE_UART3 |
| select TIVA_HAVE_I2C1 |
| select TIVA_HAVE_TIMER3 |
| select TIVA_HAVE_TIMER4 |
| select TIVA_HAVE_TIMER5 |
| select TIVA_HAVE_ETHERNET |
| select TIVA_HAVE_GPIOH_IRQS |
| |
| config ARCH_CHIP_LM4F120 |
| bool "LM4F120" |
| depends on ARCH_CHIP_LM |
| select ARCH_CORTEXM4 |
| select ARCH_CHIP_LM4F |
| select ARCH_HAVE_FPU |
| |
| config ARCH_CHIP_TM4C123AH6PM |
| bool "TM4C123AH6PM" |
| depends on ARCH_CHIP_TIVA |
| select ARCH_CHIP_TM4C |
| select ARCH_CHIP_TM4C123 |
| select TIVA_HAVE_GPIOA_IRQS |
| select TIVA_HAVE_GPIOB_IRQS |
| select TIVA_HAVE_GPIOC_IRQS |
| select TIVA_HAVE_GPIOD_IRQS |
| select TIVA_HAVE_GPIOE_IRQS |
| select TIVA_HAVE_GPIOF_IRQS |
| select TIVA_HAVE_GPIOG_IRQS |
| select TIVA_HAVE_EEPROM |
| select TIVA_HAVE_I2C4 |
| select TIVA_HAVE_I2C5 |
| select TIVA_HAVE_CAN1 |
| select TIVA_HAVE_QEI0 |
| select TIVA_HAVE_QEI1 |
| |
| config ARCH_CHIP_TM4C123GH6ZRB |
| bool "TM4C123GH6ZRB" |
| depends on ARCH_CHIP_TIVA |
| select ARCH_CHIP_TM4C |
| select ARCH_CHIP_TM4C123 |
| select TIVA_HAVE_GPIOP_IRQS |
| select TIVA_HAVE_GPIOQ_IRQS |
| select TIVA_HAVE_I2C4 |
| select TIVA_HAVE_I2C5 |
| select TIVA_HAVE_CAN1 |
| select TIVA_HAVE_QEI0 |
| select TIVA_HAVE_QEI1 |
| |
| config ARCH_CHIP_TM4C123GH6PM |
| bool "TM4C123GH6PM" |
| depends on ARCH_CHIP_TIVA |
| select ARCH_CHIP_TM4C |
| select ARCH_CHIP_TM4C123 |
| select TIVA_HAVE_GPIOA_IRQS |
| select TIVA_HAVE_GPIOB_IRQS |
| select TIVA_HAVE_GPIOC_IRQS |
| select TIVA_HAVE_GPIOD_IRQS |
| select TIVA_HAVE_GPIOE_IRQS |
| select TIVA_HAVE_GPIOF_IRQS |
| select TIVA_HAVE_ADC0 |
| select TIVA_HAVE_ADC1 |
| select TIVA_HAVE_CAN1 |
| select TIVA_HAVE_QEI0 |
| select TIVA_HAVE_QEI1 |
| |
| config ARCH_CHIP_TM4C123GH6PZ |
| bool "TM4C123GH6PZ" |
| depends on ARCH_CHIP_TIVA |
| select ARCH_CHIP_TM4C |
| select ARCH_CHIP_TM4C123 |
| select TIVA_HAVE_GPIOA_IRQS |
| select TIVA_HAVE_GPIOB_IRQS |
| select TIVA_HAVE_GPIOC_IRQS |
| select TIVA_HAVE_GPIOD_IRQS |
| select TIVA_HAVE_GPIOE_IRQS |
| select TIVA_HAVE_GPIOF_IRQS |
| select TIVA_HAVE_GPIOG_IRQS |
| select TIVA_HAVE_GPIOH_IRQS |
| select TIVA_HAVE_GPIOJ_IRQS |
| select TIVA_HAVE_GPIOK_IRQS |
| select TIVA_HAVE_ADC0 |
| select TIVA_HAVE_ADC1 |
| select TIVA_HAVE_CAN1 |
| select TIVA_HAVE_QEI0 |
| select TIVA_HAVE_QEI1 |
| |
| config ARCH_CHIP_TM4C123GH6PGE |
| bool "TM4C123GH6PGE" |
| depends on ARCH_CHIP_TIVA |
| select ARCH_CHIP_TM4C |
| select ARCH_CHIP_TM4C123 |
| select TIVA_HAVE_GPIOA_IRQS |
| select TIVA_HAVE_GPIOB_IRQS |
| select TIVA_HAVE_GPIOC_IRQS |
| select TIVA_HAVE_GPIOD_IRQS |
| select TIVA_HAVE_GPIOE_IRQS |
| select TIVA_HAVE_GPIOF_IRQS |
| select TIVA_HAVE_GPIOG_IRQS |
| select TIVA_HAVE_GPIOH_IRQS |
| select TIVA_HAVE_GPIOJ_IRQS |
| select TIVA_HAVE_GPIOK_IRQS |
| select TIVA_HAVE_GPIOL_IRQS |
| select TIVA_HAVE_GPIOM_IRQS |
| select TIVA_HAVE_GPION_IRQS |
| select TIVA_HAVE_GPIOP_IRQS |
| select TIVA_HAVE_ADC0 |
| select TIVA_HAVE_ADC1 |
| select TIVA_HAVE_CAN1 |
| select TIVA_HAVE_QEI0 |
| select TIVA_HAVE_QEI1 |
| |
| config ARCH_CHIP_TM4C1294NCPDT |
| bool "TM4C1294NCPDT" |
| depends on ARCH_CHIP_TIVA |
| select ARCH_CHIP_TM4C |
| select ARCH_CHIP_TM4C129 |
| select TIVA_HAVE_ETHERNET |
| select TIVA_HAVE_EEPROM |
| select TIVA_HAVE_GPIOG_IRQS |
| select TIVA_HAVE_GPIOH_IRQS |
| select TIVA_HAVE_GPIOJ_IRQS |
| select TIVA_HAVE_GPIOK_IRQS |
| select TIVA_HAVE_GPIOL_IRQS |
| select TIVA_HAVE_GPIOM_IRQS |
| select TIVA_HAVE_GPION_IRQS |
| select TIVA_HAVE_GPIOP_IRQS |
| select TIVA_HAVE_GPIOQ_IRQS |
| select TIVA_HAVE_CAN1 |
| select TIVA_HAVE_QEI0 |
| |
| config ARCH_CHIP_TM4C129ENCPDT |
| bool "TM4C129ENCPDT" |
| depends on ARCH_CHIP_TIVA |
| select ARCH_CHIP_TM4C |
| select ARCH_CHIP_TM4C129 |
| select TIVA_HAVE_ETHERNET |
| select TIVA_HAVE_EEPROM |
| select TIVA_HAVE_GPIOG_IRQS |
| select TIVA_HAVE_GPIOH_IRQS |
| select TIVA_HAVE_GPIOJ_IRQS |
| select TIVA_HAVE_GPIOK_IRQS |
| select TIVA_HAVE_GPIOL_IRQS |
| select TIVA_HAVE_GPIOM_IRQS |
| select TIVA_HAVE_GPION_IRQS |
| select TIVA_HAVE_GPIOP_IRQS |
| select TIVA_HAVE_GPIOQ_IRQS |
| select TIVA_HAVE_CAN1 |
| select TIVA_HAVE_QEI0 |
| |
| config ARCH_CHIP_TM4C129ENCZAD |
| bool "TM4C129ENCZAD" |
| depends on ARCH_CHIP_TIVA |
| select ARCH_CHIP_TM4C |
| select ARCH_CHIP_TM4C129 |
| select TIVA_HAVE_ETHERNET |
| select TIVA_HAVE_EEPROM |
| select TIVA_HAVE_GPIOG_IRQS |
| select TIVA_HAVE_GPIOH_IRQS |
| select TIVA_HAVE_GPIOJ_IRQS |
| select TIVA_HAVE_GPIOK_IRQS |
| select TIVA_HAVE_GPIOL_IRQS |
| select TIVA_HAVE_GPIOM_IRQS |
| select TIVA_HAVE_GPION_IRQS |
| select TIVA_HAVE_GPIOP_IRQS |
| select TIVA_HAVE_GPIOQ_IRQS |
| select TIVA_HAVE_GPIOR_IRQS |
| select TIVA_HAVE_GPIOS_IRQS |
| select TIVA_HAVE_GPIOT_IRQS |
| select TIVA_HAVE_CAN1 |
| select TIVA_HAVE_QEI0 |
| |
| config ARCH_CHIP_TM4C129XNCZAD |
| bool "TM4C129XNCZAD" |
| depends on ARCH_CHIP_TIVA |
| select ARCH_CHIP_TM4C |
| select ARCH_CHIP_TM4C129 |
| select TIVA_HAVE_ETHERNET |
| select TIVA_HAVE_GPIOG_IRQS |
| select TIVA_HAVE_GPIOH_IRQS |
| select TIVA_HAVE_GPIOJ_IRQS |
| select TIVA_HAVE_GPIOK_IRQS |
| select TIVA_HAVE_GPIOL_IRQS |
| select TIVA_HAVE_GPIOM_IRQS |
| select TIVA_HAVE_GPION_IRQS |
| select TIVA_HAVE_GPIOP_IRQS |
| select TIVA_HAVE_GPIOQ_IRQS |
| select TIVA_HAVE_GPIOR_IRQS |
| select TIVA_HAVE_GPIOS_IRQS |
| select TIVA_HAVE_GPIOT_IRQS |
| select TIVA_HAVE_CAN1 |
| select TIVA_HAVE_QEI0 |
| |
| config ARCH_CHIP_CC1310 |
| bool "CC1310 SimpleLink" |
| depends on ARCH_CHIP_SIMPLELINK || EXPERIMENTAL |
| select ARCH_CHIP_CC13X0 |
| |
| config ARCH_CHIP_CC1312R1 |
| bool "CC1312R1 SimpleLink" |
| depends on ARCH_CHIP_SIMPLELINK || EXPERIMENTAL |
| select ARCH_CHIP_CC13X2 |
| |
| config ARCH_CHIP_CC1352R1 |
| bool "CC1352R1 SimpleLink" |
| depends on ARCH_CHIP_SIMPLELINK || EXPERIMENTAL |
| select ARCH_CHIP_CC13X2 |
| |
| endchoice |
| |
| # Chip versions |
| |
| choice |
| prompt "CC13xx Chip Version" |
| default ARCH_CHIP_CC13XX_V1 |
| depends on ARCH_CHIP_CC13X0 || ARCH_CHIP_CC13X2 |
| |
| config ARCH_CHIP_CC13XX_V1 |
| bool "Version 1" |
| depends on ARCH_CHIP_CC13X2 |
| |
| config ARCH_CHIP_CC13XX_V2 |
| bool "Version 2" |
| |
| endchoice # CC13x2 Chip Version |
| |
| # Chip families |
| |
| config ARCH_CHIP_LM3S |
| bool |
| select TIVA_HAVE_GPIOA_IRQS |
| select TIVA_HAVE_GPIOB_IRQS |
| select TIVA_HAVE_GPIOC_IRQS |
| select TIVA_HAVE_GPIOD_IRQS |
| select TIVA_HAVE_GPIOE_IRQS |
| select TIVA_HAVE_GPIOF_IRQS |
| select TIVA_HAVE_GPIOG_IRQS |
| select TIVA_HAVE_SSI0 |
| select TIVA_HAVE_UART1 |
| select TIVA_HAVE_UART2 |
| select TIVA_HAVE_UART3 |
| |
| config ARCH_CHIP_LM4F |
| bool |
| select TIVA_HAVE_GPIOA_IRQS |
| select TIVA_HAVE_GPIOB_IRQS |
| select TIVA_HAVE_GPIOC_IRQS |
| select TIVA_HAVE_GPIOD_IRQS |
| select TIVA_HAVE_GPIOE_IRQS |
| select TIVA_HAVE_GPIOF_IRQS |
| select TIVA_HAVE_GPIOG_IRQS |
| select TIVA_HAVE_GPIOH_IRQS |
| select TIVA_HAVE_I2C1 |
| select TIVA_HAVE_I2C2 |
| select TIVA_HAVE_I2C3 |
| select TIVA_HAVE_UART1 |
| select TIVA_HAVE_UART2 |
| select TIVA_HAVE_UART3 |
| select TIVA_HAVE_UART4 |
| select TIVA_HAVE_UART5 |
| select TIVA_HAVE_UART6 |
| select TIVA_HAVE_UART7 |
| select TIVA_HAVE_SSI0 |
| select TIVA_HAVE_SSI1 |
| select TIVA_HAVE_SSI2 |
| select TIVA_HAVE_SSI3 |
| select TIVA_HAVE_TIMER3 |
| select TIVA_HAVE_TIMER4 |
| select TIVA_HAVE_TIMER5 |
| |
| config ARCH_CHIP_TM4C123 |
| bool |
| |
| config ARCH_CHIP_TM4C129 |
| bool |
| select TIVA_HAVE_I2C4 |
| select TIVA_HAVE_I2C5 |
| select TIVA_HAVE_I2C6 |
| select TIVA_HAVE_I2C7 |
| select TIVA_HAVE_I2C8 |
| select TIVA_HAVE_I2C9 |
| select TIVA_HAVE_TIMER6 |
| select TIVA_HAVE_TIMER7 |
| select TIVA_HAVE_UART1 |
| select TIVA_HAVE_UART2 |
| select TIVA_HAVE_UART3 |
| |
| config ARCH_CHIP_TM4C |
| bool |
| select ARCH_CORTEXM4 |
| select ARCH_HAVE_FPU |
| select TIVA_HAVE_ADC0 |
| select TIVA_HAVE_ADC1 |
| select TIVA_HAVE_CAN0 |
| select TIVA_HAVE_I2C1 |
| select TIVA_HAVE_I2C2 |
| select TIVA_HAVE_I2C3 |
| select TIVA_HAVE_SSI0 |
| select TIVA_HAVE_SSI1 |
| select TIVA_HAVE_SSI2 |
| select TIVA_HAVE_SSI3 |
| select TIVA_HAVE_TIMER0 |
| select TIVA_HAVE_TIMER1 |
| select TIVA_HAVE_TIMER2 |
| select TIVA_HAVE_TIMER3 |
| select TIVA_HAVE_TIMER4 |
| select TIVA_HAVE_TIMER5 |
| select TIVA_HAVE_UART1 |
| select TIVA_HAVE_UART2 |
| select TIVA_HAVE_UART3 |
| select TIVA_HAVE_UART4 |
| select TIVA_HAVE_UART5 |
| select TIVA_HAVE_UART6 |
| select TIVA_HAVE_UART7 |
| |
| config ARCH_CHIP_CC13X0 |
| bool |
| select ARCH_CORTEXM3 |
| select TIVA_HAVE_ADC0 |
| select TIVA_HAVE_SSI0 |
| select TIVA_HAVE_SSI1 |
| select TIVA_HAVE_TIMER0 |
| select TIVA_HAVE_TIMER1 |
| select TIVA_HAVE_TIMER2 |
| select TIVA_HAVE_TIMER3 |
| |
| config ARCH_CHIP_CC13X2 |
| bool |
| select ARCH_CORTEXM4 |
| select ARCH_HAVE_FPU |
| select TIVA_HAVE_ADC0 |
| select TIVA_HAVE_I2C1 |
| select TIVA_HAVE_SSI0 |
| select TIVA_HAVE_SSI1 |
| select TIVA_HAVE_TIMER0 |
| select TIVA_HAVE_TIMER1 |
| select TIVA_HAVE_TIMER2 |
| select TIVA_HAVE_TIMER3 |
| select TIVA_HAVE_UART1 |
| |
| config ARCH_CHIP_CC26X2 |
| bool |
| |
| config LM_REVA2 |
| bool "Rev A2" |
| default n |
| depends on ARCH_CHIP_LM |
| ---help--- |
| Some early silicon returned an increase LDO voltage or 2.75V to work |
| around a PLL bug |
| |
| menu "Tiva/Stellaris Peripheral Support" |
| |
| # MCU capabilities |
| |
| config TIVA_ADC |
| bool |
| default n |
| |
| config TIVA_HAVE_ADC0 |
| bool |
| default n |
| |
| config TIVA_HAVE_ADC1 |
| bool |
| default n |
| |
| config TIVA_CAN |
| bool |
| default n |
| select CAN |
| select CAN_TXREADY |
| select CAN_USE_RTR |
| |
| config TIVA_HAVE_CAN0 |
| bool |
| default n |
| |
| config TIVA_HAVE_CAN1 |
| bool |
| default n |
| |
| config TIVA_QEI |
| bool |
| default n |
| |
| config TIVA_HAVE_QEI0 |
| bool |
| default n |
| |
| config TIVA_HAVE_QEI1 |
| bool |
| default n |
| |
| config TIVA_I2C |
| bool |
| default n |
| |
| config TIVA_HAVE_I2C1 |
| bool |
| default n |
| |
| config TIVA_HAVE_I2C2 |
| bool |
| default n |
| |
| config TIVA_HAVE_I2C3 |
| bool |
| default n |
| |
| config TIVA_HAVE_I2C4 |
| bool |
| default n |
| |
| config TIVA_HAVE_I2C5 |
| bool |
| default n |
| |
| config TIVA_HAVE_I2C6 |
| bool |
| default n |
| |
| config TIVA_HAVE_I2C7 |
| bool |
| default n |
| |
| config TIVA_HAVE_I2C8 |
| bool |
| default n |
| |
| config TIVA_HAVE_I2C9 |
| bool |
| default n |
| |
| config TIVA_HAVE_UART1 |
| bool |
| default n |
| |
| config TIVA_HAVE_UART2 |
| bool |
| default n |
| |
| config TIVA_HAVE_UART3 |
| bool |
| default n |
| |
| config TIVA_HAVE_UART4 |
| bool |
| default n |
| |
| config TIVA_HAVE_UART5 |
| bool |
| default n |
| |
| config TIVA_HAVE_UART6 |
| bool |
| default n |
| |
| config TIVA_HAVE_UART7 |
| bool |
| default n |
| |
| config TIVA_HAVE_SSI0 |
| bool |
| default n |
| |
| config TIVA_HAVE_SSI1 |
| bool |
| default n |
| |
| config TIVA_HAVE_SSI2 |
| bool |
| default n |
| |
| config TIVA_HAVE_SSI3 |
| bool |
| default n |
| |
| config TIVA_HAVE_EEPROM |
| bool |
| default n |
| |
| config TIVA_HAVE_ETHERNET |
| bool |
| default n |
| |
| config TIVA_HAVE_TIMER0 |
| bool |
| default n |
| |
| config TIVA_HAVE_TIMER1 |
| bool |
| default n |
| |
| config TIVA_HAVE_TIMER2 |
| bool |
| default n |
| |
| config TIVA_HAVE_TIMER3 |
| bool |
| default n |
| |
| config TIVA_HAVE_TIMER4 |
| bool |
| default n |
| |
| config TIVA_HAVE_TIMER5 |
| bool |
| default n |
| |
| config TIVA_HAVE_TIMER6 |
| bool |
| default n |
| |
| config TIVA_HAVE_TIMER7 |
| bool |
| default n |
| |
| # Driver selections |
| |
| config TIVA_SSI |
| bool |
| default n |
| |
| config TIVA_TIMER |
| bool |
| default n |
| |
| # Peripheral Selections |
| |
| config TIVA_ADC0 |
| bool "ADC0" |
| default n |
| select TIVA_ADC |
| |
| config TIVA_ADC1 |
| bool "ADC1" |
| default n |
| depends on TIVA_HAVE_ADC0 |
| select TIVA_ADC |
| |
| config TIVA_CAN0 |
| bool "CAN0" |
| default n |
| depends on TIVA_HAVE_CAN0 |
| select TIVA_CAN |
| config TIVA_CAN1 |
| bool "CAN1" |
| default n |
| depends on TIVA_HAVE_CAN1 |
| select TIVA_CAN |
| |
| config TIVA_QEI0 |
| bool "QEI0" |
| default n |
| depends on TIVA_HAVE_QEI0 |
| select TIVA_QEI |
| |
| config TIVA_QEI1 |
| bool "QEI1" |
| default n |
| depends on TIVA_HAVE_QEI1 |
| select TIVA_QEI |
| |
| config TIVA_I2C0 |
| bool "I2C0" |
| default n |
| select TIVA_I2C |
| |
| config TIVA_I2C1 |
| bool "I2C1" |
| default n |
| select TIVA_I2C |
| |
| config TIVA_I2C2 |
| bool "I2C2" |
| default n |
| depends on TIVA_HAVE_I2C2 |
| select TIVA_I2C |
| |
| config TIVA_I2C3 |
| bool "I2C3" |
| default n |
| depends on TIVA_HAVE_I2C3 |
| select TIVA_I2C |
| |
| config TIVA_I2C4 |
| bool "I2C4" |
| default n |
| depends on TIVA_HAVE_I2C4 |
| select TIVA_I2C |
| |
| config TIVA_I2C5 |
| bool "I2C5" |
| default n |
| depends on TIVA_HAVE_I2C5 |
| select TIVA_I2C |
| |
| config TIVA_I2C6 |
| bool "I2C6" |
| default n |
| depends on TIVA_HAVE_I2C6 |
| select TIVA_I2C |
| |
| config TIVA_I2C7 |
| bool "I2C7" |
| default n |
| depends on TIVA_HAVE_I2C7 |
| select TIVA_I2C |
| |
| config TIVA_I2C8 |
| bool "I2C8" |
| default n |
| depends on TIVA_HAVE_I2C8 |
| select TIVA_I2C |
| |
| config TIVA_I2C9 |
| bool "I2C9" |
| default n |
| depends on TIVA_HAVE_I2C9 |
| select TIVA_I2C |
| |
| config TIVA_HCIUART |
| bool |
| default n |
| |
| choice |
| prompt "UART0 Driver Configuration" |
| default TIVA_UART0_NONE |
| |
| config TIVA_UART0_NONE |
| bool "Not selected" |
| |
| config TIVA_UART0 |
| bool "Standard serial driver" |
| select UART0_SERIALDRIVER |
| select ARCH_HAVE_SERIAL_TERMIOS |
| |
| config TIVA_UART0_HCIUART |
| bool "Bluetooth HCI-UART" |
| select TIVA_HCIUART |
| depends on WIRELESS_BLUETOOTH |
| |
| endchoice # UART0 Driver Configuration |
| |
| config TIVA_CC26X2_POWERLIB |
| bool "CC26x2 Power Library" |
| default n |
| depends on ARCH_CHIP_CC26X2 |
| |
| if TIVA_UART0_HCIUART |
| config TIVA_HCIUART0_RXBUFSIZE |
| int "HCI UART0 Rx buffer size" |
| default 80 |
| ---help--- |
| Characters are buffered as they are received. This specifies |
| the size of the receive buffer. Ideally this should be at least |
| the size of the largest frame that can be received |
| |
| config TIVA_HCIUART0_TXBUFSIZE |
| int "HCI UART0 Transmit buffer size" |
| default 80 |
| ---help--- |
| Characters are buffered before being sent. This specifies |
| the size of the transmit buffer. Ideally this should be at least |
| the size of the largest frame that can be sent |
| |
| config TIVA_HCIUART0_BAUD |
| int "HCI UART0 initial BAUD rate" |
| default 115200 |
| ---help--- |
| The configured initial BAUD of the HCI UART used during bringup. |
| In most cases this initial rate can be increased by the upper half |
| HCI UART driver using vendor-specifi HCI UART commands. |
| |
| endif # TIVA_UART0_HCIUART |
| |
| choice |
| prompt "UART1 Driver Configuration" |
| default TIVA_UART1_NONE |
| |
| config TIVA_UART1_NONE |
| bool "Not selected" |
| |
| config TIVA_UART1 |
| bool "Standard serial driver" |
| select UART1_SERIALDRIVER |
| select ARCH_HAVE_SERIAL_TERMIOS |
| |
| config TIVA_UART1_HCIUART |
| bool "Bluetooth HCI-UART" |
| select TIVA_HCIUART |
| depends on WIRELESS_BLUETOOTH |
| |
| endchoice # UART1 Driver Configuration |
| |
| if TIVA_UART1_HCIUART |
| config TIVA_HCIUART1_RXBUFSIZE |
| int "HCI UART1 Rx buffer size" |
| default 80 |
| ---help--- |
| Characters are buffered as they are received. This specifies |
| the size of the receive buffer. Ideally this should be at least |
| the size of the largest frame that can be received |
| |
| config TIVA_HCIUART1_TXBUFSIZE |
| int "HCI UART1 Transmit buffer size" |
| default 80 |
| ---help--- |
| Characters are buffered before being sent. This specifies |
| the size of the transmit buffer. Ideally this should be at least |
| the size of the largest frame that can be sent |
| |
| config TIVA_HCIUART1_BAUD |
| int "HCI UART1 initial BAUD rate" |
| default 115200 |
| ---help--- |
| The configured initial BAUD of the HCI UART used during bringup. |
| In most cases this initial rate can be increased by the upper half |
| HCI UART driver using vendor-specifi HCI UART commands. |
| |
| endif # TIVA_UART1_HCIUART |
| |
| choice |
| prompt "UART2 Driver Configuration" |
| default TIVA_UART2_NONE |
| |
| config TIVA_UART2_NONE |
| bool "Not selected" |
| |
| config TIVA_UART2 |
| bool "Standard serial driver" |
| select UART2_SERIALDRIVER |
| select ARCH_HAVE_SERIAL_TERMIOS |
| |
| config TIVA_UART2_HCIUART |
| bool "Bluetooth HCI-UART" |
| select TIVA_HCIUART |
| depends on WIRELESS_BLUETOOTH |
| |
| endchoice # UART2 Driver Configuration |
| |
| if TIVA_UART2_HCIUART |
| config TIVA_HCIUART2_RXBUFSIZE |
| int "HCI UART2 Rx buffer size" |
| default 80 |
| ---help--- |
| Characters are buffered as they are received. This specifies |
| the size of the receive buffer. Ideally this should be at least |
| the size of the largest frame that can be received |
| |
| config TIVA_HCIUART2_TXBUFSIZE |
| int "HCI UART2 Transmit buffer size" |
| default 80 |
| ---help--- |
| Characters are buffered before being sent. This specifies |
| the size of the transmit buffer. Ideally this should be at least |
| the size of the largest frame that can be sent |
| |
| config TIVA_HCIUART2_BAUD |
| int "HCI UART2 initial BAUD rate" |
| default 115200 |
| ---help--- |
| The configured initial BAUD of the HCI UART used during bringup. |
| In most cases this initial rate can be increased by the upper half |
| HCI UART driver using vendor-specifi HCI UART commands. |
| |
| endif # TIVA_UART2_HCIUART |
| |
| choice |
| prompt "UART3 Driver Configuration" |
| default TIVA_UART3_NONE |
| |
| config TIVA_UART3_NONE |
| bool "Not selected" |
| |
| config TIVA_UART3 |
| bool "Standard serial driver" |
| select UART3_SERIALDRIVER |
| select ARCH_HAVE_SERIAL_TERMIOS |
| |
| config TIVA_UART3_HCIUART |
| bool "Bluetooth HCI-UART" |
| select TIVA_HCIUART |
| depends on WIRELESS_BLUETOOTH |
| |
| endchoice # UART3 Driver Configuration |
| |
| if TIVA_UART3_HCIUART |
| config TIVA_HCIUART3_RXBUFSIZE |
| int "HCI UART3 Rx buffer size" |
| default 80 |
| ---help--- |
| Characters are buffered as they are received. This specifies |
| the size of the receive buffer. Ideally this should be at least |
| the size of the largest frame that can be received |
| |
| config TIVA_HCIUART3_TXBUFSIZE |
| int "HCI UART3 Transmit buffer size" |
| default 80 |
| ---help--- |
| Characters are buffered before being sent. This specifies |
| the size of the transmit buffer. Ideally this should be at least |
| the size of the largest frame that can be sent |
| |
| config TIVA_HCIUART3_BAUD |
| int "HCI UART3 initial BAUD rate" |
| default 115200 |
| ---help--- |
| The configured initial BAUD of the HCI UART used during bringup. |
| In most cases this initial rate can be increased by the upper half |
| HCI UART driver using vendor-specifi HCI UART commands. |
| |
| endif # TIVA_UART3_HCIUART |
| |
| choice |
| prompt "UART4 Driver Configuration" |
| default TIVA_UART4_NONE |
| |
| config TIVA_UART4_NONE |
| bool "Not selected" |
| |
| config TIVA_UART4 |
| bool "Standard serial driver" |
| select UART4_SERIALDRIVER |
| select ARCH_HAVE_SERIAL_TERMIOS |
| |
| config TIVA_UART4_HCIUART |
| bool "Bluetooth HCI-UART" |
| select TIVA_HCIUART |
| depends on WIRELESS_BLUETOOTH |
| |
| endchoice # UART4 Driver Configuration |
| |
| if TIVA_UART4_HCIUART |
| config TIVA_HCIUART4_RXBUFSIZE |
| int "HCI UART4 Rx buffer size" |
| default 80 |
| ---help--- |
| Characters are buffered as they are received. This specifies |
| the size of the receive buffer. Ideally this should be at least |
| the size of the largest frame that can be received |
| |
| config TIVA_HCIUART4_TXBUFSIZE |
| int "HCI UART4 Transmit buffer size" |
| default 80 |
| ---help--- |
| Characters are buffered before being sent. This specifies |
| the size of the transmit buffer. Ideally this should be at least |
| the size of the largest frame that can be sent |
| |
| config TIVA_HCIUART4_BAUD |
| int "HCI UART4 initial BAUD rate" |
| default 115200 |
| ---help--- |
| The configured initial BAUD of the HCI UART used during bringup. |
| In most cases this initial rate can be increased by the upper half |
| HCI UART driver using vendor-specifi HCI UART commands. |
| |
| endif # TIVA_UART4_HCIUART |
| |
| choice |
| prompt "UART5 Driver Configuration" |
| default TIVA_UART5_NONE |
| |
| config TIVA_UART5_NONE |
| bool "Not selected" |
| |
| config TIVA_UART5 |
| bool "Standard serial driver" |
| select UART5_SERIALDRIVER |
| select ARCH_HAVE_SERIAL_TERMIOS |
| |
| config TIVA_UART5_HCIUART |
| bool "Bluetooth HCI-UART" |
| select TIVA_HCIUART |
| depends on WIRELESS_BLUETOOTH |
| |
| endchoice # UART5 Driver Configuration |
| |
| if TIVA_UART5_HCIUART |
| config TIVA_HCIUART5_RXBUFSIZE |
| int "HCI UART5 Rx buffer size" |
| default 80 |
| ---help--- |
| Characters are buffered as they are received. This specifies |
| the size of the receive buffer. Ideally this should be at least |
| the size of the largest frame that can be received |
| |
| config TIVA_HCIUART5_TXBUFSIZE |
| int "HCI UART5 Transmit buffer size" |
| default 80 |
| ---help--- |
| Characters are buffered before being sent. This specifies |
| the size of the transmit buffer. Ideally this should be at least |
| the size of the largest frame that can be sent |
| |
| config TIVA_HCIUART5_BAUD |
| int "HCI UART5 initial BAUD rate" |
| default 115200 |
| ---help--- |
| The configured initial BAUD of the HCI UART used during bringup. |
| In most cases this initial rate can be increased by the upper half |
| HCI UART driver using vendor-specifi HCI UART commands. |
| |
| endif # TIVA_UART5_HCIUART |
| |
| choice |
| prompt "UART6 Driver Configuration" |
| default TIVA_UART6_NONE |
| |
| config TIVA_UART6_NONE |
| bool "Not selected" |
| |
| config TIVA_UART6 |
| bool "Standard serial driver" |
| select UART6_SERIALDRIVER |
| select ARCH_HAVE_SERIAL_TERMIOS |
| |
| config TIVA_UART6_HCIUART |
| bool "Bluetooth HCI-UART" |
| select TIVA_HCIUART |
| depends on WIRELESS_BLUETOOTH |
| |
| endchoice # UART6 Driver Configuration |
| |
| if TIVA_UART6_HCIUART |
| config TIVA_HCIUART6_RXBUFSIZE |
| int "HCI UART6 Rx buffer size" |
| default 80 |
| ---help--- |
| Characters are buffered as they are received. This specifies |
| the size of the receive buffer. Ideally this should be at least |
| the size of the largest frame that can be received |
| |
| config TIVA_HCIUART6_TXBUFSIZE |
| int "HCI UART6 Transmit buffer size" |
| default 80 |
| ---help--- |
| Characters are buffered before being sent. This specifies |
| the size of the transmit buffer. Ideally this should be at least |
| the size of the largest frame that can be sent |
| |
| config TIVA_HCIUART6_BAUD |
| int "HCI UART6 initial BAUD rate" |
| default 115200 |
| ---help--- |
| The configured initial BAUD of the HCI UART used during bringup. |
| In most cases this initial rate can be increased by the upper half |
| HCI UART driver using vendor-specifi HCI UART commands. |
| |
| endif # TIVA_UART6_HCIUART |
| |
| choice |
| prompt "UART7 Driver Configuration" |
| default TIVA_UART7_NONE |
| |
| config TIVA_UART7_NONE |
| bool "Not selected" |
| |
| config TIVA_UART7 |
| bool "Standard serial driver" |
| select UART7_SERIALDRIVER |
| select ARCH_HAVE_SERIAL_TERMIOS |
| |
| config TIVA_UART7_HCIUART |
| bool "Bluetooth HCI-UART" |
| select TIVA_HCIUART |
| depends on WIRELESS_BLUETOOTH |
| |
| endchoice # UART7 Driver Configuration |
| |
| if TIVA_UART7_HCIUART |
| config TIVA_HCIUART7_RXBUFSIZE |
| int "HCI UART7 Rx buffer size" |
| default 80 |
| ---help--- |
| Characters are buffered as they are received. This specifies |
| the size of the receive buffer. Ideally this should be at least |
| the size of the largest frame that can be received |
| |
| config TIVA_HCIUART7_TXBUFSIZE |
| int "HCI UART7 Transmit buffer size" |
| default 80 |
| ---help--- |
| Characters are buffered before being sent. This specifies |
| the size of the transmit buffer. Ideally this should be at least |
| the size of the largest frame that can be sent |
| |
| config TIVA_HCIUART7_BAUD |
| int "HCI UART7 initial BAUD rate" |
| default 115200 |
| ---help--- |
| The configured initial BAUD of the HCI UART used during bringup. |
| In most cases this initial rate can be increased by the upper half |
| HCI UART driver using vendor-specifi HCI UART commands. |
| |
| endif # TIVA_UART7_HCIUART |
| |
| menu "HCI UART Driver Configuration" |
| depends on TIVA_HCIUART |
| |
| config TIVA_HCIUART_SW_RXFLOW |
| bool "Use Software UART RTS flow control" |
| default n |
| ---help--- |
| Enable UART RTS flow control using Software. |
| |
| config TIVA_HCIUART_SW_TXFLOW |
| bool "Use Software UART CTS flow control" |
| default n |
| ---help--- |
| Enable UART CTS flow control using Software. |
| |
| endmenu # HCI UART Driver Configuration |
| |
| config TIVA_UART_BREAKS |
| bool "Add TIOxSBRK to support sending Breaks" |
| depends on TIVA_UART0 || TIVA_UART1 || TIVA_UART2 || TIVA_UART3 || TIVA_UART4 || TIVA_UART5 || TIVA_UART6 || TIVA_UART7 |
| default n |
| ---help--- |
| Add TIOCxBRK routines to send a BSD compatible line break. |
| TIOCSBRK will start the break and TIOCCBRK will end the break. |
| This implementation uses the BRK bit (bit 0) of the UART Line |
| Control register (UARTLCRH) to send the break. The break begins |
| after the UART finishes shifting out the current character in |
| progress, if any, including its stop bit(s), and continues |
| indefinitely until stopped by software. |
| |
| config TIVA_SSI0 |
| bool "SSI0" |
| default n |
| depends on TIVA_HAVE_SSI0 |
| select TIVA_SSI |
| |
| config TIVA_SSI1 |
| bool "SSI1" |
| default n |
| depends on TIVA_HAVE_SSI1 |
| select TIVA_SSI |
| |
| config TIVA_SSI2 |
| bool "SSI2" |
| default n |
| depends on TIVA_HAVE_SSI2 |
| select TIVA_SSI |
| |
| config TIVA_SSI3 |
| bool "SSI3" |
| default n |
| depends on TIVA_HAVE_SSI3 |
| select TIVA_SSI |
| |
| config TIVA_TIMER0 |
| bool "16-/32-bit Timer 0" |
| default n |
| depends on TIVA_HAVE_TIMER0 |
| select TIVA_TIMER |
| |
| config TIVA_TIMER1 |
| bool "16-/32-bit Timer 1" |
| default n |
| depends on TIVA_HAVE_TIMER1 |
| select TIVA_TIMER |
| |
| config TIVA_TIMER2 |
| bool "16-/32-bit Timer 2" |
| default n |
| depends on TIVA_HAVE_TIMER2 |
| select TIVA_TIMER |
| |
| config TIVA_TIMER3 |
| bool "16-/32-bit Timer 3" |
| default n |
| depends on TIVA_HAVE_TIMER3 |
| select TIVA_TIMER |
| |
| config TIVA_TIMER4 |
| bool "16-/32-bit Timer 4" |
| default n |
| depends on TIVA_HAVE_TIMER4 |
| select TIVA_TIMER |
| |
| config TIVA_TIMER5 |
| bool "16-/32-bit Timer 5" |
| default n |
| depends on TIVA_HAVE_TIMER5 |
| select TIVA_TIMER |
| |
| config TIVA_TIMER6 |
| bool "16-/32-bit Timer 6" |
| default n |
| depends on TIVA_HAVE_TIMER6 |
| select TIVA_TIMER |
| |
| config TIVA_TIMER7 |
| bool "16-/32-bit Timer 7" |
| default n |
| depends on TIVA_HAVE_TIMER7 |
| select TIVA_TIMER |
| |
| config TIVA_ETHERNET |
| bool "Ethernet" |
| default n |
| depends on TIVA_HAVE_ETHERNET |
| select NETDEVICES |
| select ARCH_HAVE_PHY |
| select ARCH_HAVE_NETDEV_STATISTICS if ARCH_CHIP_LM3S || ARCH_CHIP_LM4F |
| ---help--- |
| This must be set (along with NET) to build the Stellaris Ethernet driver. |
| |
| config TIVA_FLASH |
| bool "Internal FLASH driver" |
| default n |
| ---help--- |
| Enable MTD driver support for internal FLASH. |
| |
| config TIVA_EEPROM |
| bool "Internal EEPROM driver" |
| default n |
| depends on TIVA_HAVE_EEPROM && EXPERIMENTAL |
| ---help--- |
| Enable MTD driver support for internal EEPROM. |
| |
| endmenu |
| |
| config TIVA_RAMVBAR |
| bool "Set VBAR" |
| default n |
| ---help--- |
| Set the ARM VBAR register to position interrupt vectors at the |
| beginning of RAM (vs the beginning of FLASH). The beginning of RAM |
| is that address defined by CONFIG_RAM_START. |
| |
| menu "Enable GPIO Interrupts" |
| |
| config TIVA_GPIO_IRQS |
| bool |
| default n |
| |
| config TIVA_HAVE_GPIOA_IRQS |
| bool |
| default n |
| |
| config TIVA_HAVE_GPIOB_IRQS |
| bool |
| default n |
| |
| config TIVA_HAVE_GPIOC_IRQS |
| bool |
| default n |
| |
| config TIVA_HAVE_GPIOD_IRQS |
| bool |
| default n |
| |
| config TIVA_HAVE_GPIOE_IRQS |
| bool |
| default n |
| |
| config TIVA_HAVE_GPIOF_IRQS |
| bool |
| default n |
| |
| config TIVA_HAVE_GPIOG_IRQS |
| bool |
| default n |
| |
| config TIVA_HAVE_GPIOH_IRQS |
| bool |
| default n |
| |
| config TIVA_HAVE_GPIOJ_IRQS |
| bool |
| default n |
| |
| config TIVA_HAVE_GPIOK_IRQS |
| bool |
| default n |
| |
| config TIVA_HAVE_GPIOL_IRQS |
| bool |
| default n |
| |
| config TIVA_HAVE_GPIOM_IRQS |
| bool |
| default n |
| |
| config TIVA_HAVE_GPION_IRQS |
| bool |
| default n |
| |
| config TIVA_HAVE_GPIOP_IRQS |
| bool |
| default n |
| |
| config TIVA_HAVE_GPIOQ_IRQS |
| bool |
| default n |
| |
| config TIVA_HAVE_GPIOR_IRQS |
| bool |
| default n |
| |
| config TIVA_HAVE_GPIOS_IRQS |
| bool |
| default n |
| |
| config TIVA_HAVE_GPIOT_IRQS |
| bool |
| default n |
| |
| config TIVA_GPIOA_IRQS |
| bool "Enable GPIOA IRQs" |
| default n |
| depends on TIVA_HAVE_GPIOA_IRQS |
| select TIVA_GPIO_IRQS |
| |
| config TIVA_GPIOB_IRQS |
| bool "Enable GPIOB IRQs" |
| default n |
| depends on TIVA_HAVE_GPIOB_IRQS |
| select TIVA_GPIO_IRQS |
| |
| config TIVA_GPIOC_IRQS |
| bool "Enable GPIOC IRQs" |
| default n |
| depends on TIVA_HAVE_GPIOC_IRQS |
| select TIVA_GPIO_IRQS |
| |
| config TIVA_GPIOD_IRQS |
| bool "Enable GPIOD IRQs" |
| default n |
| depends on TIVA_HAVE_GPIOD_IRQS |
| select TIVA_GPIO_IRQS |
| |
| config TIVA_GPIOE_IRQS |
| bool "Enable GPIOE IRQs" |
| default n |
| depends on TIVA_HAVE_GPIOE_IRQS |
| select TIVA_GPIO_IRQS |
| |
| config TIVA_GPIOF_IRQS |
| bool "Enable GPIOF IRQs" |
| default n |
| depends on TIVA_HAVE_GPIOF_IRQS |
| select TIVA_GPIO_IRQS |
| |
| config TIVA_GPIOG_IRQS |
| bool "Enable GPIOG IRQs" |
| default n |
| depends on TIVA_HAVE_GPIOG_IRQS |
| select TIVA_GPIO_IRQS |
| |
| config TIVA_GPIOH_IRQS |
| bool "Enable GPIOH IRQs" |
| default n |
| depends on TIVA_HAVE_GPIOH_IRQS |
| select TIVA_GPIO_IRQS |
| |
| config TIVA_GPIOJ_IRQS |
| bool "Enable GPIOJ IRQs" |
| default n |
| depends on TIVA_HAVE_GPIOJ_IRQS |
| select TIVA_GPIO_IRQS |
| |
| config TIVA_GPIOK_IRQS |
| bool "Enable GPIOK IRQs" |
| default n |
| depends on TIVA_HAVE_GPIOK_IRQS |
| select TIVA_GPIO_IRQS |
| |
| config TIVA_GPIOL_IRQS |
| bool "Enable GPIOL IRQs" |
| default n |
| depends on TIVA_HAVE_GPIOL_IRQS |
| select TIVA_GPIO_IRQS |
| |
| config TIVA_GPIOM_IRQS |
| bool "Enable GPIOM IRQs" |
| default n |
| depends on TIVA_HAVE_GPIOM_IRQS |
| select TIVA_GPIO_IRQS |
| |
| config TIVA_GPION_IRQS |
| bool "Enable GPION IRQs" |
| default n |
| depends on TIVA_HAVE_GPION_IRQS |
| select TIVA_GPIO_IRQS |
| |
| config TIVA_GPIOP_IRQS |
| bool "Enable GPIOP IRQs" |
| default n |
| depends on TIVA_HAVE_GPIOP_IRQS |
| select TIVA_GPIO_IRQS |
| |
| config TIVA_GPIOQ_IRQS |
| bool "Enable GPIOQ IRQs" |
| default n |
| depends on TIVA_HAVE_GPIOQ_IRQS |
| select TIVA_GPIO_IRQS |
| |
| config TIVA_GPIOR_IRQS |
| bool "Enable GPIOR IRQs" |
| default n |
| depends on TIVA_HAVE_GPIOR_IRQS |
| select TIVA_GPIO_IRQS |
| |
| config TIVA_GPIOS_IRQS |
| bool "Enable GPIOS IRQs" |
| default n |
| depends on TIVA_HAVE_GPIOS_IRQS |
| select TIVA_GPIO_IRQS |
| |
| config TIVA_GPIOT_IRQS |
| bool "Enable GPIOT IRQs" |
| default n |
| depends on TIVA_HAVE_GPIOT_IRQS |
| select TIVA_GPIO_IRQS |
| |
| endmenu |
| |
| if TIVA_I2C |
| |
| menu "I2C Configuration" |
| |
| config TIVA_I2C_DYNTIMEO |
| bool "Use dynamic timeouts" |
| default n |
| |
| if TIVA_I2C_DYNTIMEO |
| |
| config TIVA_I2C_DYNTIMEO_USECPERBYTE |
| int "Timeout Microseconds per Byte" |
| default 500 |
| |
| config TIVA_I2C_DYNTIMEO_STARTSTOP |
| int "Timeout for Start/Stop (Milliseconds)" |
| default 1000 |
| |
| endif # TIVA_I2C_DYNTIMEO |
| |
| config TIVA_I2C_TIMEOSEC |
| int "Timeout seconds" |
| default 0 |
| |
| if !TIVA_I2C_DYNTIMEO |
| |
| config TIVA_I2C_TIMEOMS |
| int "Timeout Milliseconds" |
| default 500 |
| depends on !TIVA_I2C_DYNTIMEO |
| |
| config TIVA_I2C_TIMEOTICKS |
| int "Timeout for Done and Stop (ticks)" |
| default 500 |
| depends on !TIVA_I2C_DYNTIMEO |
| |
| endif # !TIVA_I2C_DYNTIMEO |
| |
| config TIVA_I2C_HIGHSPEED |
| bool "High speed support" |
| default n |
| depends on ARCH_CHIP_TM4C && EXPERIMENTAL |
| ---help--- |
| Enable support for high speed I2C transfers. |
| Only partially implemented and completely untested. |
| |
| config TIVA_I2C_REGDEBUG |
| bool "Register level debug" |
| default n |
| depends on DEBUG_I2C_INFO |
| ---help--- |
| Enables extremely detailed register access debug output. |
| |
| endmenu # I2C Configuration |
| endif # TIVA_I2C |
| |
| if TIVA_TIMER |
| |
| menu "Timer Configuration" |
| |
| config TIVA_TIMER_32BIT |
| bool "32-bit timer support" |
| default n |
| |
| if TIVA_TIMER_32BIT |
| |
| config TIVA_TIMER32_PERIODIC |
| bool "32-bit one-shot/periodic timer support" |
| default n |
| |
| config TIVA_TIMER32_RTC |
| bool "32-bit RTC (needs 32.768-KHz input)" |
| default n |
| |
| endif # TIVA_TIMER_32BIT |
| |
| config TIVA_TIMER_16BIT |
| bool "16-bit timer support" |
| default n |
| |
| if TIVA_TIMER_16BIT |
| |
| config TIVA_TIMER16_PERIODIC |
| bool "16-bit one-shot/periodic timer support" |
| default n |
| |
| config TIVA_TIMER16_EDGECOUNT |
| bool "16-bit input edge-count capture support" |
| default n |
| depends on EXPERIMENTAL |
| |
| config TIVA_TIMER16_TIMECAP |
| bool "16-bit input time capture support" |
| default n |
| depends on EXPERIMENTAL |
| |
| config TIVA_TIMER16_PWM |
| bool "16-bit PWM output support" |
| default n |
| ---help--- |
| Enables 24-bit PWM mode using a 16-bit half-timer of a |
| Tiva 16/32-bit General Purpose Timer Module (GPTM) block. |
| The 24-bit resolution is achieved by using the prescaler |
| as the high 8 bits. |
| |
| endif # TIVA_TIMER_16BIT |
| |
| config TIVA_TIMER_REGDEBUG |
| bool "Register level debug" |
| default n |
| depends on DEBUG_TIMER_INFO |
| ---help--- |
| Enables extremely detailed register access debug output. |
| |
| endmenu # Tiva Timer Configuration |
| endif # TIVA_TIMER |
| |
| if TIVA_ADC |
| menu "ADC Configuration" |
| |
| config TIVA_ADC_REGDEBUG |
| bool "Register level debug" |
| default n |
| depends on DEBUG_ANALOG_INFO |
| ---help--- |
| Enables extremely detailed register access debug output. |
| |
| endmenu # Tiva ADC Configuration |
| endif # TIVA_ADC |
| |
| menu "CAN Driver Configuration" |
| depends on TIVA_CAN |
| choice |
| prompt "CAN bus driver selection" |
| default TIVA_SOCKET_CAN |
| |
| config TIVA_SOCKET_CAN |
| bool "Use SocketCAN driver" |
| depends on (TIVA_CAN0 || TIVA_CAN1) && NET_CAN |
| select NET_CAN_HAVE_ERRORS |
| |
| config TIVA_CHAR_DEV_CAN |
| bool "Character device driver" |
| depends on (TIVA_CAN0 || TIVA_CAN1) && !NET_CAN |
| select ARCH_HAVE_CAN_ERRORS |
| |
| endchoice # CAN driver selection |
| |
| config TIVA_CAN0_PRIO |
| int "CAN0 kthread priority" |
| default 300 |
| depends on TIVA_CAN0 && TIVA_CHAR_DEV_CAN |
| ---help--- |
| The Tiva CAN driver retrieves messages using a kthread rather |
| than in the ISR or using a work queue. The ISR signals the |
| kthread, but the kthread can be preempted if needed. This |
| option sets the thread priority for CAN module 0. |
| |
| config TIVA_CAN0_BAUD |
| int "CAN0 baud rate kb/s" |
| default 125 |
| depends on TIVA_CAN0 && TIVA_SOCKET_CAN |
| |
| config TIVA_CAN1_BAUD |
| int "CAN1 baud rate kb/s" |
| default 125 |
| depends on TIVA_CAN1 && TIVA_SOCKET_CAN |
| |
| config TIVA_CAN1_PRIO |
| int "CAN1 kthread priority" |
| default 300 |
| depends on TIVA_CAN1 && TIVA_CHAR_DEV_CAN |
| ---help--- |
| The Tiva CAN driver retrieves messages using a kthread rather |
| than in the ISR or using a work queue. The ISR signals the |
| kthread, but the kthread can be preempted if needed. This |
| option sets the thread priority for CAN module 1. |
| |
| config TIVA_CAN_REGDEBUG |
| bool "CAN register level debug" |
| depends on DEBUG_CAN_INFO && TIVA_CHAR_DEV_CAN |
| default n |
| ---help--- |
| Output detailed register-level CAN device debug information. |
| Requires also CONFIG_DEBUG_CAN_INFO. |
| |
| config TIVA_CAN_TX_FIFO_DEPTH |
| int "Size of the hardware TX FIFO" |
| range 1 31 |
| default 8 |
| ---help--- |
| This number determines the depth of the hardware transmit |
| FIFO, which cannot be resized. Using a transmit FIFO allows |
| the application to transmit messages at maximum speed and |
| reduces jitter caused by excessive interrupts. However, it |
| occupies extra mailboxes that might be used for more fine- |
| grained filtering; hence there is a trade-off. |
| |
| Because the mailboxes on the Tiva chips cannot be used as |
| a ring buffer for outbound messages, a larger TX FIFO |
| directly increases the maximum number of messages that |
| can be sent in a "burst" at maximum speed. |
| |
| However, the TX FIFO makes implementation of |
| "pre-arbitration" more difficult. Although the classic |
| character device CAN model does not support this anyway, |
| transmission of a higher-priority message would require |
| cancelling and reenqueuing of the low-priority messages |
| already in the hardware. |
| |
| config TIVA_CAN_DEFAULT_FIFO_DEPTH |
| int "Default CAN message RX FIFO depth" |
| range 1 31 |
| default 6 |
| ---help--- |
| This number determines the default depth for all RX |
| hardware FIFOs in the CAN module. The size of a FIFO can be |
| adjusted at any time (and made deeper than this number if |
| needed) via the various CANIOC_TIVA ioctls. However, this |
| option is limited to 31 because the driver must allocate |
| at least one mailbox for outbound (TX) messages. The default |
| RX filter FIFO is set to allow any messages, but is |
| reconfigured as soon as an application uses the |
| CANIOC_ADD_STDFILTER or CANIOC_ADD_EXTFILTER. |
| |
| config TIVA_CAN_FILTERS_MAX |
| int "Maximum number of CAN RX filters" |
| range 1 31 |
| default 4 |
| ---help--- |
| This number applies to both CAN0 and CAN1, if the chip has |
| both. (This is the number of filters for each module, not the |
| total for both CAN modules.) |
| The Tiva CAN modules have 32 message objects. Only one is |
| used for TX, so it is possible to have up to 31 unique |
| RX filters. However, increasing the FIFO depth of a filter |
| uses up message objects and reduces this number. Additionally, |
| since the driver has to keep track of the message objects |
| assigned to each filter, increasing the number of available |
| filters increases the memory footprint even if the filters |
| are not used (internally, it is a statically-allocated array). |
| |
| config TIVA_CAN_ERR_HANDLER_PER |
| int "Rate-limited error handling period (milliseconds)" |
| range 10 1000 |
| default 100 |
| depends on CAN_ERRORS || NET_CAN_ERRORS |
| ---help--- |
| When error messages (CAN_ERRORS) are enabled, the Tiva |
| CAN driver will disable interrupts for individual errors |
| when the application fails to call read() quickly enough |
| to keep up. This can easily happen during testing if no |
| transceiver is connected and the application is trying |
| to print error messages to a serial console. |
| |
| When this happens, the driver defers error reporting to |
| a periodic task in the high-priority work queue. The task |
| checks for errors and reports them at the specified |
| interval. It is unlikely that the bus would be disturbed |
| badly enough to cause interrupt overload and yet be usable |
| for real-time communication, so successful transmission or |
| reception of a message will return the driver to the |
| normal interrupt handling mode. |
| |
| endmenu |
| |
| config TIVA_WITH_QEMU |
| bool "Run with qemu" |
| default n |
| |
| if TIVA_ETHERNET |
| |
| menu "Stellaris Ethernet Configuration" |
| depends on ARCH_CHIP_LM3S |
| |
| config TIVA_ETHLEDS |
| bool "Ethernet LEDs" |
| default n |
| ---help--- |
| Enable to use Ethernet LEDs on the board. |
| |
| config TIVA_ETHHDUPLEX |
| bool "Force Half Duplex" |
| default n |
| ---help--- |
| Set to force half duplex operation |
| |
| config TIVA_ETHNOAUTOCRC |
| bool "Disable auto-CRC" |
| default n |
| ---help--- |
| Set to suppress auto-CRC generation |
| |
| config TIVA_ETHNOPAD |
| bool "Disable Tx Padding" |
| default n |
| ---help--- |
| Set to suppress Tx padding |
| |
| config TIVA_MULTICAST |
| bool "Enable Multicast" |
| default n |
| ---help--- |
| Set to enable multicast frames |
| |
| config TIVA_PROMISCUOUS |
| bool "Enable Promiscuous Mode" |
| default n |
| ---help--- |
| Set to enable promiscuous mode |
| |
| config TIVA_TIMESTAMP |
| bool "Enable Timestamping" |
| default n |
| |
| config TIVA_BADCRC |
| bool "Enable Bad CRC Rejection" |
| default n |
| ---help--- |
| Set to enable bad CRC rejection. |
| |
| config TIVA_DUMPPACKET |
| bool "Dump Packets" |
| default n |
| ---help--- |
| Dump each packet received/sent to the console. |
| |
| endmenu # Stellaris Ethernet Configuration |
| |
| menu "Ethernet Configuration" |
| depends on ARCH_CHIP_TM4C |
| |
| choice |
| prompt "PHY selection" |
| default TIVA_PHY_INTERNAL |
| |
| config TIVA_PHY_INTERNAL |
| bool "Internal PHY" |
| ---help--- |
| Use the built-in, internal Tiva PHY |
| |
| config TIVA_PHY_MII |
| bool "External MII interface" |
| depends on EXPERIMENTAL |
| ---help--- |
| Support external PHY MII interface. |
| |
| config TIVA_PHY_RMII |
| bool "External RMII interface" |
| depends on EXPERIMENTAL |
| ---help--- |
| Support external PHY RMII interface. |
| |
| endchoice # PHY selection |
| |
| config TIVA_AUTONEG |
| bool "Use autonegotiation" |
| default y |
| ---help--- |
| Use PHY autonegotiation to determine speed and mode |
| |
| if !TIVA_PHY_INTERNAL |
| |
| config TIVA_PHYADDR |
| int "PHY address" |
| default 1 |
| ---help--- |
| The 5-bit address of the PHY on the board. Default: 1 |
| |
| if !TIVA_AUTONEG |
| config TIVA_ETHFD |
| bool "Full duplex" |
| default n |
| ---help--- |
| If TIVA_AUTONEG is not defined, then this may be defined to select full duplex |
| mode. Default: half-duplex |
| |
| config TIVA_ETH100MBPS |
| bool "100 Mbps" |
| default n |
| ---help--- |
| If TIVA_AUTONEG is not defined, then this may be defined to select 100 MBps |
| speed. Default: 10 Mbps |
| |
| endif # !TIVA_AUTONEG |
| if TIVA_AUTONEG |
| |
| config TIVA_PHYSR |
| int "PHY Status Register Address (decimal)" |
| ---help--- |
| This must be provided if TIVA_AUTONEG is defined. The PHY status register |
| address may diff from PHY to PHY. This configuration sets the address of |
| the PHY status register. |
| |
| config TIVA_PHYSR_ALTCONFIG |
| bool "PHY Status Alternate Bit Layout" |
| default n |
| ---help--- |
| Different PHYs present speed and mode information in different ways. Some |
| will present separate information for speed and mode (this is the default). |
| Those PHYs, for example, may provide a 10/100 Mbps indication and a separate |
| full/half duplex indication. This options selects an alternative representation |
| where speed and mode information are combined. This might mean, for example, |
| separate bits for 10HD, 100HD, 10FD and 100FD. |
| |
| if !TIVA_PHYSR_ALTCONFIG |
| |
| config TIVA_PHYSR_SPEED |
| hex "PHY Speed Mask" |
| ---help--- |
| This must be provided if TIVA_AUTONEG is defined. This provides bit mask |
| for isolating the 10 or 100MBps speed indication. |
| |
| config TIVA_PHYSR_100MBPS |
| hex "PHY 100Mbps Speed Value" |
| ---help--- |
| This must be provided if TIVA_AUTONEG is defined. This provides the value |
| of the speed bit(s) indicating 100MBps speed. |
| |
| config TIVA_PHYSR_MODE |
| hex "PHY Mode Mask" |
| ---help--- |
| This must be provided if TIVA_AUTONEG is defined. This provide bit mask |
| for isolating the full or half duplex mode bits. |
| |
| config TIVA_PHYSR_FULLDUPLEX |
| hex "PHY Full Duplex Mode Value" |
| ---help--- |
| This must be provided if TIVA_AUTONEG is defined. This provides the |
| value of the mode bits indicating full duplex mode. |
| |
| endif # !TIVA_PHYSR_ALTCONFIG |
| if TIVA_PHYSR_ALTCONFIG |
| |
| config TIVA_PHYSR_ALTMODE |
| hex "PHY Mode Mask" |
| ---help--- |
| This must be provided if TIVA_AUTONEG is defined. This provide bit mask |
| for isolating the speed and full/half duplex mode bits. |
| |
| config TIVA_PHYSR_10HD |
| hex "10MBase-T Half Duplex Value" |
| ---help--- |
| This must be provided if TIVA_AUTONEG is defined. This is the value |
| under the bit mask that represents the 10Mbps, half duplex setting. |
| |
| config TIVA_PHYSR_100HD |
| hex "100Base-T Half Duplex Value" |
| ---help--- |
| This must be provided if TIVA_AUTONEG is defined. This is the value |
| under the bit mask that represents the 100Mbps, half duplex setting. |
| |
| config TIVA_PHYSR_10FD |
| hex "10Base-T Full Duplex Value" |
| ---help--- |
| This must be provided if TIVA_AUTONEG is defined. This is the value |
| under the bit mask that represents the 10Mbps, full duplex setting. |
| |
| config TIVA_PHYSR_100FD |
| hex "100Base-T Full Duplex Value" |
| ---help--- |
| This must be provided if TIVA_AUTONEG is defined. This is the value |
| under the bit mask that represents the 100Mbps, full duplex setting. |
| |
| endif # TIVA_PHYSR_ALTCONFIG |
| endif # TIVA_AUTONEG |
| endif # !TIVA_PHY_INTERNAL |
| |
| config TIVA_PHY_INTERRUPTS |
| bool "PHY interrupt support" |
| select ARCH_PHY_INTERRUPT |
| select NETDEV_PHY_IOCTL |
| default n |
| ---help--- |
| Enable logic to signal user tasks when a PHY interrupt occurs. The |
| PHY interrupt may indicate a change in the link status such as, for |
| example, when a cable is plugged in or unplugged. |
| |
| config TIVA_EMAC_NRXDESC |
| int "Number of RX descriptors" |
| default 8 |
| ---help--- |
| Number of RX DMA descriptors to use. |
| |
| config TIVA_EMAC_NTXDESC |
| int "Number of TX descriptors" |
| default 4 |
| ---help--- |
| Number of TX DMA descriptors to use. |
| |
| config TIVA_EMAC_ENHANCEDDESC |
| bool |
| default n |
| |
| config TIVA_EMAC_PTP |
| bool "Precision Time Protocol (PTP)" |
| default n |
| depends on EXPERIMENTAL |
| select TIVA_EMAC_ENHANCEDDESC |
| ---help--- |
| Precision Time Protocol (PTP). Not supported but some hooks are indicated |
| with this condition. |
| |
| config TIVA_EMAC_HWCHECKSUM |
| bool "Use hardware checksums" |
| default n |
| depends on EXPERIMENTAL |
| ---help--- |
| Use the hardware checksum capabilities of the Tiva chip |
| |
| config TIVA_ETHERNET_REGDEBUG |
| bool "Register-Level Debug" |
| default n |
| depends on DEBUG_NET_INFO |
| ---help--- |
| Enable very low-level register access debug. Depends on CONFIG_DEBUG_FEATURES. |
| |
| endmenu # Tiva Ethernet Configuration |
| |
| config TIVA_BOARDMAC |
| bool "Board MAC" |
| default n |
| ---help--- |
| If the board-specific logic can provide a MAC address (via |
| tiva_ethernetmac()), then this should be selected. |
| |
| endif # TIVA_ETHERNET |
| |
| if TIVA_SSI |
| menu "Tiva/Stellaris SSI Configuration" |
| |
| config SSI_POLLWAIT |
| bool "Poll Wait (No-Interrupt) Mode" |
| default y |
| |
| config SSI_TXLIMIT |
| int "Tx Limit" |
| default 4 |
| ---help--- |
| Default of 4 assumes half of the 8 entry FIFO |
| |
| endmenu |
| endif |
| |
| if TIVA_FLASH |
| menu "Tiva/Stellaris Internal Flash Driver Configuration" |
| |
| config TIVA_FLASH_STARTPAGE |
| int "First page accessible by the MTD driver" |
| default 250 |
| ---help--- |
| To prevent accessing FLASH sections where code is stored. |
| |
| endmenu |
| endif |
