Google Git
Sign in
apache / nuttx / ca5a9c711a7b9b70d84385a8523c54cf58a24e9e / . / arch / arm / src / stm32h7 / stm32_spi.c
blob: d128f884a927fd156464be479a06b7d2f1046b5a [file] [log] [blame]
/****************************************************************************
* arch/arm/src/stm32h7/stm32_spi.c
*
* Licensed to the Apache Software Foundation (ASF) under one or more
* contributor license agreements. See the NOTICE file distributed with
* this work for additional information regarding copyright ownership. The
* ASF licenses this file to you under the Apache License, Version 2.0 (the
* "License"); you may not use this file except in compliance with the
* License. You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
* License for the specific language governing permissions and limitations
* under the License.
*
****************************************************************************/
/****************************************************************************
* The external functions, stm32_spi1/2/3/4/5/6select and
* stm32_spi1/2/3/4/5/6status must be provided by board-specific logic. They
* are implementations of the select and status methods of the SPI interface
* defined by struct spi_ops_s (see include/nuttx/spi/spi.h). All other
* methods (including stm32_spibus_initialize()) are provided by common STM32
* logic. To use this common SPI logic on your board:
*
* 1. Provide logic in stm32_boardinitialize() to configure SPI chip select
* pins.
* 2. Provide stm32_spi1/2/3/4/5/6select() and stm32_spi1/2/3/4/5/6status()
* functions in your board-specific logic. These functions will perform
* chip selection and status operations using GPIOs in the way your
* board is configured.
* 3. Add a calls to stm32_spibus_initialize() in your low level
* application initialization logic
* 4. The handle returned by stm32_spibus_initialize() may then be used to
* bind the SPI driver to higher level logic (e.g., calling
* mmcsd_spislotinitialize(), for example, will bind the SPI driver to
* the SPI MMC/SD driver).
*
****************************************************************************/
/****************************************************************************
* Included Files
****************************************************************************/
#include <nuttx/config.h>
#include <sys/types.h>
#include <inttypes.h>
#include <stdint.h>
#include <stdbool.h>
#include <stddef.h>
#include <string.h>
#include <assert.h>
#include <errno.h>
#include <debug.h>
#include <nuttx/irq.h>
#include <nuttx/arch.h>
#include <nuttx/compiler.h>
#include <nuttx/mutex.h>
#include <nuttx/spi/spi.h>
#include <nuttx/power/pm.h>
#include <arch/board/board.h>
#include "arm_internal.h"
#include "chip.h"
#include "stm32_rcc.h"
#include "stm32_gpio.h"
#include "stm32_spi.h"
#include "stm32_dma.h"
#if defined(CONFIG_STM32H7_SPI1) || defined(CONFIG_STM32H7_SPI2) || \
defined(CONFIG_STM32H7_SPI3) || defined(CONFIG_STM32H7_SPI4) || \
defined(CONFIG_STM32H7_SPI5) || defined(CONFIG_STM32H7_SPI6)
/****************************************************************************
* Pre-processor Definitions
****************************************************************************/
/* Configuration ************************************************************/
/* SPI interrupts */
#ifdef CONFIG_STM32H7_SPI_INTERRUPTS
# error "Interrupt driven SPI not yet supported"
#endif
/* Can't have both interrupt driven SPI and SPI DMA */
#if defined(CONFIG_STM32H7_SPI_INTERRUPTS) && defined(CONFIG_STM32H7_SPI_DMA)
# error "Cannot enable both interrupt mode and DMA mode for SPI"
#endif
/* SPI DMA priority */
#ifdef CONFIG_STM32H7_SPI_DMA
# if defined(CONFIG_SPI_DMAPRIO)
# define SPI_DMA_PRIO CONFIG_SPI_DMAPRIO
# elif defined(DMA_SCR_PRIMED)
# define SPI_DMA_PRIO DMA_SCR_PRILO
# else
# error "Unknown STM32 DMA"
# endif
# if (SPI_DMA_PRIO & ~DMA_SCR_PL_MASK) != 0
# error "Illegal value for CONFIG_SPI_DMAPRIO"
# endif
/* DMA channel configuration */
# define SPI_RXDMA16_CONFIG (SPI_DMA_PRIO|DMA_SCR_MSIZE_16BITS|DMA_SCR_PSIZE_16BITS|DMA_SCR_MINC|DMA_SCR_DIR_P2M)
# define SPI_RXDMA8_CONFIG (SPI_DMA_PRIO|DMA_SCR_MSIZE_8BITS |DMA_SCR_PSIZE_8BITS |DMA_SCR_MINC|DMA_SCR_DIR_P2M)
# define SPI_RXDMA16NULL_CONFIG (SPI_DMA_PRIO|DMA_SCR_MSIZE_8BITS |DMA_SCR_PSIZE_16BITS |DMA_SCR_DIR_P2M)
# define SPI_RXDMA8NULL_CONFIG (SPI_DMA_PRIO|DMA_SCR_MSIZE_8BITS |DMA_SCR_PSIZE_8BITS |DMA_SCR_DIR_P2M)
# define SPI_TXDMA16_CONFIG (SPI_DMA_PRIO|DMA_SCR_MSIZE_16BITS|DMA_SCR_PSIZE_16BITS|DMA_SCR_MINC|DMA_SCR_DIR_M2P)
# define SPI_TXDMA8_CONFIG (SPI_DMA_PRIO|DMA_SCR_MSIZE_8BITS |DMA_SCR_PSIZE_8BITS |DMA_SCR_MINC|DMA_SCR_DIR_M2P)
# define SPI_TXDMA16NULL_CONFIG (SPI_DMA_PRIO|DMA_SCR_MSIZE_8BITS |DMA_SCR_PSIZE_16BITS |DMA_SCR_DIR_M2P)
# define SPI_TXDMA8NULL_CONFIG (SPI_DMA_PRIO|DMA_SCR_MSIZE_8BITS |DMA_SCR_PSIZE_8BITS |DMA_SCR_DIR_M2P)
/* If built with CONFIG_ARMV7M_DCACHE Buffers need to be aligned and
* multiples of ARMV7M_DCACHE_LINESIZE
*/
# if defined(CONFIG_ARMV7M_DCACHE)
# define SPIDMA_BUFFER_MASK (ARMV7M_DCACHE_LINESIZE - 1)
# define SPIDMA_SIZE(b) (((b) + SPIDMA_BUFFER_MASK) & ~SPIDMA_BUFFER_MASK)
# define SPIDMA_BUF_ALIGN aligned_data(ARMV7M_DCACHE_LINESIZE)
# else
# define SPIDMA_SIZE(b) (b)
# define SPIDMA_BUF_ALIGN
# endif
# if defined(CONFIG_STM32H7_SPI1_DMA_BUFFER) && \
CONFIG_STM32H7_SPI1_DMA_BUFFER > 0
# define SPI1_DMABUFSIZE_ADJUSTED SPIDMA_SIZE(CONFIG_STM32H7_SPI1_DMA_BUFFER)
# define SPI1_DMABUFSIZE_ALGN SPIDMA_BUF_ALIGN
# endif
# if defined(CONFIG_STM32H7_SPI2_DMA_BUFFER) && \
CONFIG_STM32H7_SPI2_DMA_BUFFER > 0
# define SPI2_DMABUFSIZE_ADJUSTED SPIDMA_SIZE(CONFIG_STM32H7_SPI2_DMA_BUFFER)
# define SPI2_DMABUFSIZE_ALGN SPIDMA_BUF_ALIGN
# endif
# if defined(CONFIG_STM32H7_SPI3_DMA_BUFFER) && \
CONFIG_STM32H7_SPI3_DMA_BUFFER > 0
# define SPI3_DMABUFSIZE_ADJUSTED SPIDMA_SIZE(CONFIG_STM32H7_SPI3_DMA_BUFFER)
# define SPI3_DMABUFSIZE_ALGN SPIDMA_BUF_ALIGN
# endif
# if defined(CONFIG_STM32H7_SPI4_DMA_BUFFER) && \
CONFIG_STM32H7_SPI4_DMA_BUFFER > 0
# define SPI4_DMABUFSIZE_ADJUSTED SPIDMA_SIZE(CONFIG_STM32H7_SPI4_DMA_BUFFER)
# define SPI4_DMABUFSIZE_ALGN SPIDMA_BUF_ALIGN
# endif
# if defined(CONFIG_STM32H7_SPI5_DMA_BUFFER) && \
CONFIG_STM32H7_SPI5_DMA_BUFFER > 0
# define SPI5_DMABUFSIZE_ADJUSTED SPIDMA_SIZE(CONFIG_STM32H7_SPI5_DMA_BUFFER)
# define SPI5_DMABUFSIZE_ALGN SPIDMA_BUF_ALIGN
# endif
#if defined(CONFIG_STM32H7_SPI6_DMA_BUFFER) && \
CONFIG_STM32H7_SPI6_DMA_BUFFER > 0
# define SPI6_DMABUFSIZE_ADJUSTED SPIDMA_SIZE(CONFIG_STM32H7_SPI6_DMA_BUFFER)
# define SPI6_DMABUFSIZE_ALGN SPIDMA_BUF_ALIGN
# endif
#endif
/* Kernel clock configuration
* TODO:
* - support for all kernel clock configuration
*/
#if defined(CONFIG_STM32H7_SPI1) || defined(CONFIG_STM32H7_SPI2) || \
defined(CONFIG_STM32H7_SPI3)
# if STM32_RCC_D2CCIP1R_SPI123SRC == RCC_D2CCIP1R_SPI123SEL_PLL1
# define SPI123_KERNEL_CLOCK_FREQ STM32_PLL1Q_FREQUENCY
# elif STM32_RCC_D2CCIP1R_SPI123SRC == RCC_D2CCIP1R_SPI123SEL_PLL2
# define SPI123_KERNEL_CLOCK_FREQ STM32_PLL2P_FREQUENCY
# else
# error Not supported yet
# endif
# if SPI123_KERNEL_CLOCK_FREQ > 200000000
# error Not supported SPI123 frequency
# endif
#endif /* SPI123 */
#if defined(CONFIG_STM32H7_SPI4) || defined(CONFIG_STM32H7_SPI5)
# if STM32_RCC_D2CCIP1R_SPI45SRC == RCC_D2CCIP1R_SPI45SEL_APB
# define SPI45_KERNEL_CLOCK_FREQ STM32_PCLK2_FREQUENCY
# elif STM32_RCC_D2CCIP1R_SPI45SRC == RCC_D2CCIP1R_SPI45SEL_PLL2
# define SPI45_KERNEL_CLOCK_FREQ STM32_PLL2Q_FREQUENCY
# else
# error Not supported yet
# endif
# if SPI45_KERNEL_CLOCK_FREQ > 100000000
# error Not supported SPI45 frequency
# endif
#endif /* SPI45 */
#if defined(CONFIG_STM32H7_SPI6)
# if STM32_RCC_D3CCIPR_SPI6SRC == RCC_D3CCIPR_SPI6SEL_PCLK4
# define SPI6_KERNEL_CLOCK_FREQ STM32_PCLK4_FREQUENCY
# elif STM32_RCC_D3CCIPR_SPI6SRC == RCC_D3CCIPR_SPI6SEL_PLL2
# define SPI6_KERNEL_CLOCK_FREQ STM32_PLL2Q_FREQUENCY
# else
# error Not supported yet
# endif
# if SPI6_KERNEL_CLOCK_FREQ > 100000000
# error Not supported SPI6 frequency
# endif
#endif /* SPI6 */
/****************************************************************************
* Private Types
****************************************************************************/
enum spi_config_e
{
FULL_DUPLEX = 0,
SIMPLEX_TX,
SIMPLEX_RX,
HALF_DUPLEX
};
struct stm32_spidev_s
{
struct spi_dev_s spidev; /* Externally visible part of the SPI interface */
uint32_t spibase; /* SPIn base address */
uint32_t spiclock; /* Clocking for the SPI module */
uint8_t spiirq; /* SPI IRQ number */
#ifdef CONFIG_STM32H7_SPI_DMA
volatile uint8_t rxresult; /* Result of the RX DMA */
volatile uint8_t txresult; /* Result of the RX DMA */
#ifdef CONFIG_SPI_TRIGGER
bool defertrig; /* Flag indicating that trigger should be deferred */
bool trigarmed; /* Flag indicating that the trigger is armed */
#endif
uint32_t rxch; /* The RX DMA channel number */
uint32_t txch; /* The TX DMA channel number */
uint8_t *rxbuf; /* The RX DMA buffer */
uint8_t *txbuf; /* The TX DMA buffer */
size_t buflen; /* The DMA buffer length */
DMA_HANDLE rxdma; /* DMA channel handle for RX transfers */
DMA_HANDLE txdma; /* DMA channel handle for TX transfers */
sem_t rxsem; /* Wait for RX DMA to complete */
sem_t txsem; /* Wait for TX DMA to complete */
uint32_t txccr; /* DMA control register for TX transfers */
uint32_t rxccr; /* DMA control register for RX transfers */
#endif
bool initialized; /* Has SPI interface been initialized */
mutex_t lock; /* Held while chip is selected for mutual exclusion */
uint32_t frequency; /* Requested clock frequency */
uint32_t actual; /* Actual clock frequency */
int8_t nbits; /* Width of word in bits */
uint8_t mode; /* Mode 0,1,2,3 */
#ifdef CONFIG_PM
struct pm_callback_s pm_cb; /* PM callbacks */
#endif
enum spi_config_e config; /* full/half duplex, simplex transmit/read only */
};
/****************************************************************************
* Private Function Prototypes
****************************************************************************/
/* Helpers */
static inline uint32_t spi_getreg(struct stm32_spidev_s *priv,
uint32_t offset);
static inline void spi_putreg(struct stm32_spidev_s *priv,
uint32_t offset, uint32_t value);
static inline uint32_t spi_readword(struct stm32_spidev_s *priv);
static inline void spi_writeword(struct stm32_spidev_s *priv,
uint32_t byte);
#ifdef CONFIG_DEBUG_SPI_INFO
static inline void spi_dumpregs(struct stm32_spidev_s *priv);
#endif
/* DMA support */
#ifdef CONFIG_STM32H7_SPI_DMA
static int spi_dmarxwait(struct stm32_spidev_s *priv);
static int spi_dmatxwait(struct stm32_spidev_s *priv);
static inline void spi_dmarxwakeup(struct stm32_spidev_s *priv);
static void spi_dmarxcallback(DMA_HANDLE handle, uint8_t isr,
void *arg);
static void spi_dmarxsetup(struct stm32_spidev_s *priv,
void *rxbuffer,
void *rxdummy,
size_t nwords,
stm32_dmacfg_t *dmacfg);
static void spi_dmatxsetup(struct stm32_spidev_s *priv,
const void *txbuffer,
const void *txdummy,
size_t nwords,
stm32_dmacfg_t *dmacfg);
static inline void spi_dmarxstart(struct stm32_spidev_s *priv);
static inline void spi_dmatxstart(struct stm32_spidev_s *priv);
#endif
/* SPI methods */
static int spi_lock(struct spi_dev_s *dev, bool lock);
static uint32_t spi_setfrequency(struct spi_dev_s *dev,
uint32_t frequency);
#ifdef CONFIG_SPI_DELAY_CONTROL
static int spi_setdelay(struct spi_dev_s *dev, uint32_t startdelay,
uint32_t stopdelay, uint32_t csdelay,
uint32_t ifdelay);
#endif
static void spi_setmode(struct spi_dev_s *dev,
enum spi_mode_e mode);
static void spi_setbits(struct spi_dev_s *dev, int nbits);
#ifdef CONFIG_SPI_HWFEATURES
static int spi_hwfeatures(struct spi_dev_s *dev,
spi_hwfeatures_t features);
#endif
static uint32_t spi_send(struct spi_dev_s *dev, uint32_t wd);
static void spi_exchange(struct spi_dev_s *dev,
const void *txbuffer, void *rxbuffer,
size_t nwords);
#ifdef CONFIG_SPI_TRIGGER
static int spi_trigger(struct spi_dev_s *dev);
#endif
#ifndef CONFIG_SPI_EXCHANGE
static void spi_sndblock(struct spi_dev_s *dev,
const void *txbuffer, size_t nwords);
static void spi_recvblock(struct spi_dev_s *dev,
void *rxbuffer, size_t nwords);
#endif
/* Initialization */
static void spi_bus_initialize(struct stm32_spidev_s *priv);
/* PM interface */
#ifdef CONFIG_PM
static int spi_pm_prepare(struct pm_callback_s *cb, int domain,
enum pm_state_e pmstate);
#endif
/****************************************************************************
* Private Data
****************************************************************************/
#ifdef CONFIG_STM32H7_SPI1
static const struct spi_ops_s g_sp1iops =
{
.lock = spi_lock,
.select = stm32_spi1select,
.setfrequency = spi_setfrequency,
#ifdef CONFIG_SPI_DELAY_CONTROL
.setdelay = spi_setdelay,
#endif
.setmode = spi_setmode,
.setbits = spi_setbits,
#ifdef CONFIG_SPI_HWFEATURES
.hwfeatures = spi_hwfeatures,
#endif
.status = stm32_spi1status,
#ifdef CONFIG_SPI_CMDDATA
.cmddata = stm32_spi1cmddata,
#endif
.send = spi_send,
#ifdef CONFIG_SPI_EXCHANGE
.exchange = spi_exchange,
#else
.sndblock = spi_sndblock,
.recvblock = spi_recvblock,
#endif
#ifdef CONFIG_SPI_TRIGGER
.trigger = spi_trigger,
#endif
#ifdef CONFIG_SPI_CALLBACK
.registercallback = stm32_spi1register, /* Provided externally */
#else
.registercallback = 0, /* Not implemented */
#endif
};
#if defined(SPI1_DMABUFSIZE_ADJUSTED)
static uint8_t g_spi1_txbuf[SPI1_DMABUFSIZE_ADJUSTED] SPI1_DMABUFSIZE_ALGN;
static uint8_t g_spi1_rxbuf[SPI1_DMABUFSIZE_ADJUSTED] SPI1_DMABUFSIZE_ALGN;
#endif
static struct stm32_spidev_s g_spi1dev =
{
.spidev =
{
.ops = &g_sp1iops,
},
.spibase = STM32_SPI1_BASE,
.spiclock = SPI123_KERNEL_CLOCK_FREQ,
.spiirq = STM32_IRQ_SPI1,
#ifdef CONFIG_STM32H7_SPI1_DMA
.rxch = DMAMAP_SPI1_RX,
.txch = DMAMAP_SPI1_TX,
# if defined(SPI1_DMABUFSIZE_ADJUSTED)
.rxbuf = g_spi1_rxbuf,
.txbuf = g_spi1_txbuf,
.buflen = SPI1_DMABUFSIZE_ADJUSTED,
# endif
.rxsem = SEM_INITIALIZER(0),
.txsem = SEM_INITIALIZER(0),
#endif
.lock = NXMUTEX_INITIALIZER,
#ifdef CONFIG_PM
.pm_cb.prepare = spi_pm_prepare,
#endif
#ifdef CONFIG_STM32H7_SPI1_COMMTYPE
.config = CONFIG_STM32H7_SPI1_COMMTYPE,
#else
.config = FULL_DUPLEX,
#endif
};
#endif /* CONFIG_STM32H7_SPI1 */
#ifdef CONFIG_STM32H7_SPI2
static const struct spi_ops_s g_sp2iops =
{
.lock = spi_lock,
.select = stm32_spi2select,
.setfrequency = spi_setfrequency,
#ifdef CONFIG_SPI_DELAY_CONTROL
.setdelay = spi_setdelay,
#endif
.setmode = spi_setmode,
.setbits = spi_setbits,
#ifdef CONFIG_SPI_HWFEATURES
.hwfeatures = spi_hwfeatures,
#endif
.status = stm32_spi2status,
#ifdef CONFIG_SPI_CMDDATA
.cmddata = stm32_spi2cmddata,
#endif
.send = spi_send,
#ifdef CONFIG_SPI_EXCHANGE
.exchange = spi_exchange,
#else
.sndblock = spi_sndblock,
.recvblock = spi_recvblock,
#endif
#ifdef CONFIG_SPI_TRIGGER
.trigger = spi_trigger,
#endif
#ifdef CONFIG_SPI_CALLBACK
.registercallback = stm32_spi2register, /* provided externally */
#else
.registercallback = 0, /* not implemented */
#endif
};
#if defined(SPI2_DMABUFSIZE_ADJUSTED)
static uint8_t g_spi2_txbuf[SPI2_DMABUFSIZE_ADJUSTED] SPI2_DMABUFSIZE_ALGN;
static uint8_t g_spi2_rxbuf[SPI2_DMABUFSIZE_ADJUSTED] SPI2_DMABUFSIZE_ALGN;
#endif
static struct stm32_spidev_s g_spi2dev =
{
.spidev =
{
.ops = &g_sp2iops,
},
.spibase = STM32_SPI2_BASE,
.spiclock = SPI123_KERNEL_CLOCK_FREQ,
.spiirq = STM32_IRQ_SPI2,
#ifdef CONFIG_STM32H7_SPI2_DMA
.rxch = DMAMAP_SPI2_RX,
.txch = DMAMAP_SPI2_TX,
# if defined(SPI2_DMABUFSIZE_ADJUSTED)
.rxbuf = g_spi2_rxbuf,
.txbuf = g_spi2_txbuf,
.buflen = SPI2_DMABUFSIZE_ADJUSTED,
# endif
.rxsem = SEM_INITIALIZER(0),
.txsem = SEM_INITIALIZER(0),
#endif
.lock = NXMUTEX_INITIALIZER,
#ifdef CONFIG_PM
.pm_cb.prepare = spi_pm_prepare,
#endif
#ifdef CONFIG_STM32H7_SPI2_COMMTYPE
.config = CONFIG_STM32H7_SPI2_COMMTYPE,
#else
.config = FULL_DUPLEX,
#endif
};
#endif /* CONFIG_STM32H7_SPI2 */
#ifdef CONFIG_STM32H7_SPI3
static const struct spi_ops_s g_sp3iops =
{
.lock = spi_lock,
.select = stm32_spi3select,
.setfrequency = spi_setfrequency,
#ifdef CONFIG_SPI_DELAY_CONTROL
.setdelay = spi_setdelay,
#endif
.setmode = spi_setmode,
.setbits = spi_setbits,
#ifdef CONFIG_SPI_HWFEATURES
.hwfeatures = spi_hwfeatures,
#endif
.status = stm32_spi3status,
#ifdef CONFIG_SPI_CMDDATA
.cmddata = stm32_spi3cmddata,
#endif
.send = spi_send,
#ifdef CONFIG_SPI_EXCHANGE
.exchange = spi_exchange,
#else
.sndblock = spi_sndblock,
.recvblock = spi_recvblock,
#endif
#ifdef CONFIG_SPI_TRIGGER
.trigger = spi_trigger,
#endif
#ifdef CONFIG_SPI_CALLBACK
.registercallback = stm32_spi3register, /* provided externally */
#else
.registercallback = 0, /* not implemented */
#endif
};
#if defined(SPI3_DMABUFSIZE_ADJUSTED)
static uint8_t g_spi3_txbuf[SPI3_DMABUFSIZE_ADJUSTED] SPI3_DMABUFSIZE_ALGN;
static uint8_t g_spi3_rxbuf[SPI3_DMABUFSIZE_ADJUSTED] SPI3_DMABUFSIZE_ALGN;
#endif
static struct stm32_spidev_s g_spi3dev =
{
.spidev =
{
.ops = &g_sp3iops,
},
.spibase = STM32_SPI3_BASE,
.spiclock = SPI123_KERNEL_CLOCK_FREQ,
.spiirq = STM32_IRQ_SPI3,
#ifdef CONFIG_STM32H7_SPI3_DMA
.rxch = DMAMAP_SPI3_RX,
.txch = DMAMAP_SPI3_TX,
# if defined(SPI3_DMABUFSIZE_ADJUSTED)
.rxbuf = g_spi3_rxbuf,
.txbuf = g_spi3_txbuf,
.buflen = SPI3_DMABUFSIZE_ADJUSTED,
# endif
.rxsem = SEM_INITIALIZER(0),
.txsem = SEM_INITIALIZER(0),
#endif
.lock = NXMUTEX_INITIALIZER,
#ifdef CONFIG_PM
.pm_cb.prepare = spi_pm_prepare,
#endif
#ifdef CONFIG_STM32H7_SPI3_COMMTYPE
.config = CONFIG_STM32H7_SPI3_COMMTYPE,
#else
.config = FULL_DUPLEX,
#endif
};
#endif /* CONFIG_STM32H7_SPI3 */
#ifdef CONFIG_STM32H7_SPI4
static const struct spi_ops_s g_sp4iops =
{
.lock = spi_lock,
.select = stm32_spi4select,
.setfrequency = spi_setfrequency,
#ifdef CONFIG_SPI_DELAY_CONTROL
.setdelay = spi_setdelay,
#endif
.setmode = spi_setmode,
.setbits = spi_setbits,
#ifdef CONFIG_SPI_HWFEATURES
.hwfeatures = spi_hwfeatures,
#endif
.status = stm32_spi4status,
#ifdef CONFIG_SPI_CMDDATA
.cmddata = stm32_spi4cmddata,
#endif
.send = spi_send,
#ifdef CONFIG_SPI_EXCHANGE
.exchange = spi_exchange,
#else
.sndblock = spi_sndblock,
.recvblock = spi_recvblock,
#endif
#ifdef CONFIG_SPI_TRIGGER
.trigger = spi_trigger,
#endif
#ifdef CONFIG_SPI_CALLBACK
.registercallback = stm32_spi4register, /* provided externally */
#else
.registercallback = 0, /* not implemented */
#endif
};
#if defined(SPI4_DMABUFSIZE_ADJUSTED)
static uint8_t g_spi4_txbuf[SPI4_DMABUFSIZE_ADJUSTED] SPI4_DMABUFSIZE_ALGN;
static uint8_t g_spi4_rxbuf[SPI4_DMABUFSIZE_ADJUSTED] SPI4_DMABUFSIZE_ALGN;
#endif
static struct stm32_spidev_s g_spi4dev =
{
.spidev =
{
.ops = &g_sp4iops,
},
.spibase = STM32_SPI4_BASE,
.spiclock = SPI45_KERNEL_CLOCK_FREQ,
.spiirq = STM32_IRQ_SPI4,
#ifdef CONFIG_STM32H7_SPI4_DMA
.rxch = DMAMAP_SPI4_RX,
.txch = DMAMAP_SPI4_TX,
# if defined(SPI4_DMABUFSIZE_ADJUSTED)
.rxbuf = g_spi4_rxbuf,
.txbuf = g_spi4_txbuf,
.buflen = SPI4_DMABUFSIZE_ADJUSTED,
# endif
.rxsem = SEM_INITIALIZER(0),
.txsem = SEM_INITIALIZER(0),
#endif
.lock = NXMUTEX_INITIALIZER,
#ifdef CONFIG_PM
.pm_cb.prepare = spi_pm_prepare,
#endif
#ifdef CONFIG_STM32H7_SPI4_COMMTYPE
.config = CONFIG_STM32H7_SPI4_COMMTYPE,
#else
.config = FULL_DUPLEX,
#endif
};
#endif /* CONFIG_STM32H7_SPI4 */
#ifdef CONFIG_STM32H7_SPI5
static const struct spi_ops_s g_sp5iops =
{
.lock = spi_lock,
.select = stm32_spi5select,
.setfrequency = spi_setfrequency,
#ifdef CONFIG_SPI_DELAY_CONTROL
.setdelay = spi_setdelay,
#endif
.setmode = spi_setmode,
.setbits = spi_setbits,
#ifdef CONFIG_SPI_HWFEATURES
.hwfeatures = spi_hwfeatures,
#endif
.status = stm32_spi5status,
#ifdef CONFIG_SPI_CMDDATA
.cmddata = stm32_spi5cmddata,
#endif
.send = spi_send,
#ifdef CONFIG_SPI_EXCHANGE
.exchange = spi_exchange,
#else
.sndblock = spi_sndblock,
.recvblock = spi_recvblock,
#endif
#ifdef CONFIG_SPI_TRIGGER
.trigger = spi_trigger,
#endif
#ifdef CONFIG_SPI_CALLBACK
.registercallback = stm32_spi5register, /* provided externally */
#else
.registercallback = 0, /* not implemented */
#endif
};
#if defined(SPI5_DMABUFSIZE_ADJUSTED)
static uint8_t g_spi5_txbuf[SPI5_DMABUFSIZE_ADJUSTED] SPI5_DMABUFSIZE_ALGN;
static uint8_t g_spi5_rxbuf[SPI5_DMABUFSIZE_ADJUSTED] SPI5_DMABUFSIZE_ALGN;
#endif
static struct stm32_spidev_s g_spi5dev =
{
.spidev =
{
.ops = &g_sp5iops,
},
.spibase = STM32_SPI5_BASE,
.spiclock = SPI45_KERNEL_CLOCK_FREQ,
.spiirq = STM32_IRQ_SPI5,
#ifdef CONFIG_STM32H7_SPI5_DMA
.rxch = DMAMAP_SPI5_RX,
.txch = DMAMAP_SPI5_TX,
# if defined(SPI5_DMABUFSIZE_ADJUSTED)
.rxbuf = g_spi5_rxbuf,
.txbuf = g_spi5_txbuf,
.buflen = SPI5_DMABUFSIZE_ADJUSTED,
# endif
.rxsem = SEM_INITIALIZER(0),
.txsem = SEM_INITIALIZER(0),
#endif
.lock = NXMUTEX_INITIALIZER,
#ifdef CONFIG_PM
.pm_cb.prepare = spi_pm_prepare,
#endif
#ifdef CONFIG_STM32H7_SPI5_COMMTYPE
.config = CONFIG_STM32H7_SPI5_COMMTYPE,
#else
.config = FULL_DUPLEX,
#endif
};
#endif /* CONFIG_STM32H7_SPI5 */
#ifdef CONFIG_STM32H7_SPI6
static const struct spi_ops_s g_sp6iops =
{
.lock = spi_lock,
.select = stm32_spi6select,
.setfrequency = spi_setfrequency,
#ifdef CONFIG_SPI_DELAY_CONTROL
.setdelay = spi_setdelay,
#endif
.setmode = spi_setmode,
.setbits = spi_setbits,
#ifdef CONFIG_SPI_HWFEATURES
.hwfeatures = spi_hwfeatures,
#endif
.status = stm32_spi6status,
#ifdef CONFIG_SPI_CMDDATA
.cmddata = stm32_spi3cmddata,
#endif
.send = spi_send,
#ifdef CONFIG_SPI_EXCHANGE
.exchange = spi_exchange,
#else
.sndblock = spi_sndblock,
.recvblock = spi_recvblock,
#endif
#ifdef CONFIG_SPI_TRIGGER
.trigger = spi_trigger,
#endif
#ifdef CONFIG_SPI_CALLBACK
.registercallback = stm32_spi6register, /* provided externally */
#else
.registercallback = 0, /* not implemented */
#endif
};
#if defined(SPI6_DMABUFSIZE_ADJUSTED)
static uint8_t g_spi6_txbuf[SPI6_DMABUFSIZE_ADJUSTED] SPI6_DMABUFSIZE_ALGN
locate_data(".sram4");
static uint8_t g_spi6_rxbuf[SPI6_DMABUFSIZE_ADJUSTED] SPI6_DMABUFSIZE_ALGN
locate_data(".sram4");
#endif
static struct stm32_spidev_s g_spi6dev =
{
.spidev =
{
.ops = &g_sp6iops,
},
.spibase = STM32_SPI6_BASE,
.spiclock = SPI6_KERNEL_CLOCK_FREQ,
.spiirq = STM32_IRQ_SPI6,
#ifdef CONFIG_STM32H7_SPI6_DMA
.rxch = DMAMAP_SPI6_RX,
.txch = DMAMAP_SPI6_TX,
# if defined(SPI6_DMABUFSIZE_ADJUSTED)
.rxbuf = g_spi6_rxbuf,
.txbuf = g_spi6_txbuf,
.buflen = SPI6_DMABUFSIZE_ADJUSTED,
# endif
.rxsem = SEM_INITIALIZER(0),
.txsem = SEM_INITIALIZER(0),
#endif
.lock = NXMUTEX_INITIALIZER,
#ifdef CONFIG_PM
.pm_cb.prepare = spi_pm_prepare,
#endif
#ifdef CONFIG_STM32H7_SPI6_COMMTYPE
.config = CONFIG_STM32H7_SPI6_COMMTYPE,
#else
.config = FULL_DUPLEX,
#endif
};
#endif /* CONFIG_STM32H7_SPI6 */
/****************************************************************************
* Private Functions
****************************************************************************/
/****************************************************************************
* Name: spi_getreg8
*
* Description:
* Get the contents of the SPI register at offset
*
* Input Parameters:
* priv - private SPI device structure
* offset - offset to the register of interest
*
* Returned Value:
* The contents of the 8-bit register
*
****************************************************************************/
static inline uint8_t spi_getreg8(struct stm32_spidev_s *priv,
uint32_t offset)
{
return getreg8(priv->spibase + offset);
}
/****************************************************************************
* Name: spi_putreg8
*
* Description:
* Write a 8-bit value to the SPI register at offset
*
* Input Parameters:
* priv - private SPI device structure
* offset - offset to the register of interest
* value - the 8-bit value to be written
*
****************************************************************************/
static inline void spi_putreg8(struct stm32_spidev_s *priv,
uint32_t offset, uint8_t value)
{
putreg8(value, priv->spibase + offset);
}
/****************************************************************************
* Name: spi_getreg16
*
* Description:
* Get the contents of the SPI register at offset
*
* Input Parameters:
* priv - private SPI device structure
* offset - offset to the register of interest
*
* Returned Value:
* The contents of the 16-bit register
*
****************************************************************************/
static inline uint16_t spi_getreg16(struct stm32_spidev_s *priv,
uint32_t offset)
{
return getreg16(priv->spibase + offset);
}
/****************************************************************************
* Name: spi_putreg16
*
* Description:
* Write a 16-bit value to the SPI register at offset
*
* Input Parameters:
* priv - private SPI device structure
* offset - offset to the register of interest
* value - the 16-bit value to be written
*
****************************************************************************/
static inline void spi_putreg16(struct stm32_spidev_s *priv,
uint32_t offset, uint16_t value)
{
putreg16(value, priv->spibase + offset);
}
/****************************************************************************
* Name: spi_getreg
*
* Description:
* Get the contents of the SPI register at offset
*
* Input Parameters:
* priv - private SPI device structure
* offset - offset to the register of interest
*
* Returned Value:
* The contents of the 16-bit register
*
****************************************************************************/
static inline uint32_t spi_getreg(struct stm32_spidev_s *priv,
uint32_t offset)
{
return getreg32(priv->spibase + offset);
}
/****************************************************************************
* Name: spi_putreg
*
* Description:
* Write a 16-bit value to the SPI register at offset
*
* Input Parameters:
* priv - private SPI device structure
* offset - offset to the register of interest
* value - the 16-bit value to be written
*
* Returned Value:
* The contents of the 16-bit register
*
****************************************************************************/
static inline void spi_putreg(struct stm32_spidev_s *priv,
uint32_t offset, uint32_t value)
{
putreg32(value, priv->spibase + offset);
}
/****************************************************************************
* Name: spi_modifyreg
*
* Description:
* Modify an SPI register
*
****************************************************************************/
static void spi_modifyreg(struct stm32_spidev_s *priv, uint32_t offset,
uint32_t clrbits, uint32_t setbits)
{
/* Only 32-bit registers */
modifyreg32(priv->spibase + offset, clrbits, setbits);
}
/****************************************************************************
* Name: spi_readword
*
* Description:
* Read one byte from SPI
*
* Input Parameters:
* priv - Device-specific state data
*
* Returned Value:
* Byte as read
*
****************************************************************************/
static inline uint32_t spi_readword(struct stm32_spidev_s *priv)
{
/* Can't receive in tx only mode */
if (priv->config == SIMPLEX_TX)
{
return 0;
}
/* Wait until the receive buffer is not empty */
while ((spi_getreg(priv, STM32_SPI_SR_OFFSET) & SPI_SR_RXP) == 0);
/* Then return the received 16 bit word */
return spi_getreg16(priv, STM32_SPI_RXDR_OFFSET);
}
/****************************************************************************
* Name: spi_writeword
*
* Description:
* Write one byte to SPI
*
* Input Parameters:
* priv - Device-specific state data
* byte - Byte to send
*
* Returned Value:
* None
*
****************************************************************************/
static inline void spi_writeword(struct stm32_spidev_s *priv,
uint32_t word)
{
/* Can't transmit in rx only mode */
if (priv->config == SIMPLEX_RX)
{
return;
}
/* Wait until the transmit buffer is empty */
while ((spi_getreg(priv, STM32_SPI_SR_OFFSET) & SPI_SR_TXP) == 0);
/* Then send the 16 bit word */
spi_putreg16(priv, STM32_SPI_TXDR_OFFSET, word);
}
/****************************************************************************
* Name: spi_readbyte
*
* Description:
* Read one byte from SPI
*
* Input Parameters:
* priv - Device-specific state data
*
* Returned Value:
* Byte as read
*
****************************************************************************/
static inline uint8_t spi_readbyte(struct stm32_spidev_s *priv)
{
/* Can't receive in tx only mode */
if (priv->config == SIMPLEX_TX)
{
return 0;
}
/* Wait until the receive buffer is not empty */
while ((spi_getreg(priv, STM32_SPI_SR_OFFSET) & SPI_SR_RXP) == 0);
/* Then return the received byte */
return spi_getreg8(priv, STM32_SPI_RXDR_OFFSET);
}
/****************************************************************************
* Name: spi_writebyte
*
* Description:
* Write one 8-bit frame to the SPI FIFO
*
* Input Parameters:
* priv - Device-specific state data
* byte - Byte to send
*
* Returned Value:
* None
*
****************************************************************************/
static inline void spi_writebyte(struct stm32_spidev_s *priv,
uint8_t byte)
{
/* Can't transmit in rx only mode */
if (priv->config == SIMPLEX_RX)
{
return;
}
/* Wait until the transmit buffer is empty */
while ((spi_getreg(priv, STM32_SPI_SR_OFFSET) & SPI_SR_TXP) == 0);
/* Then send the byte */
spi_putreg8(priv, STM32_SPI_TXDR_OFFSET, byte);
}
/****************************************************************************
* Name: spi_dumpregs
****************************************************************************/
#ifdef CONFIG_DEBUG_SPI_INFO
static void spi_dumpregs(struct stm32_spidev_s *priv)
{
spiinfo("CR1: 0x%08" PRIx32 " CFG1: 0x%08" PRIx32
" CFG2: 0x%08" PRIx32 "\n",
spi_getreg(priv, STM32_SPI_CR1_OFFSET),
spi_getreg(priv, STM32_SPI_CFG1_OFFSET),
spi_getreg(priv, STM32_SPI_CFG2_OFFSET));
spiinfo("IER: 0x%08" PRIx32 " SR: 0x%08" PRIx32
" I2SCFGR: 0x%08" PRIx32 "\n",
spi_getreg(priv, STM32_SPI_IER_OFFSET),
spi_getreg(priv, STM32_SPI_SR_OFFSET),
spi_getreg(priv, STM32_SPI_I2SCFGR_OFFSET));
}
#endif
/****************************************************************************
* Name: spi_interrupt
*
* Description:
* In DMA transfer mode, handle the transmission complete interrupt
*
****************************************************************************/
static int spi_interrupt(int irq, void *context, void *arg)
{
struct stm32_spidev_s *priv = (struct stm32_spidev_s *)arg;
uint32_t sr = spi_getreg(priv, STM32_SPI_SR_OFFSET);
if (sr & SPI_SR_TXC)
{
/* Disable interrupt. This needs to be done
* before disabling SPI to avoid spurious TXC interrupt
* (ERRATA: Q2.14.4 TXP interrupt occurring while SPI/I2Sdisabled")
* There is no need to clear the interrupt since it is disabled and
* SPI will be disabled after transmit as well.
*/
spi_modifyreg(priv, STM32_SPI_IER_OFFSET, SPI_IER_EOTIE, 0);
/* Set result and release wait semaphore */
#ifdef CONFIG_STM32H7_SPI_DMA
priv->txresult = 0x80;
nxsem_post(&priv->txsem);
#endif
}
return 0;
}
/****************************************************************************
* Name: spi_dmarxwait
*
* Description:
* Wait for DMA to complete.
*
****************************************************************************/
#ifdef CONFIG_STM32H7_SPI_DMA
static int spi_dmarxwait(struct stm32_spidev_s *priv)
{
int ret;
/* Don't wait in tx only mode */
if (priv->config == SIMPLEX_TX)
{
return OK;
}
/* Take the semaphore (perhaps waiting). If the result is zero, then the
* DMA must not really have completed???
*/
do
{
ret = nxsem_wait_uninterruptible(&priv->rxsem);
/* The only expected error is ECANCELED which would occur if the
* calling thread were canceled.
*/
DEBUGASSERT(ret == OK || ret == -ECANCELED);
}
while (priv->rxresult == 0 && ret == OK);
return ret;
}
#endif
/****************************************************************************
* Name: spi_dmatxwait
*
* Description:
* Wait for DMA to complete.
*
****************************************************************************/
#ifdef CONFIG_STM32H7_SPI_DMA
static int spi_dmatxwait(struct stm32_spidev_s *priv)
{
int ret;
/* Don't wait in rx only mode */
if (priv->config == SIMPLEX_RX)
{
return OK;
}
/* Enable TXC interrupt. This needs to be done after starting TX-dma AND
* when spi is enabled to avoid spurious TXC interrupt (ERRATA:
* "2.14.4 TXP interrupt occurring while SPI/I2Sdisabled")
* It is fine to enable this interrupt even if the transfer already did
* complete; in this case the irq will just fire right away
*/
spi_modifyreg(priv, STM32_SPI_IER_OFFSET, 0, SPI_IER_EOTIE);
/* Take the semaphore (perhaps waiting). If the result is zero, then the
* DMA must not really have completed???
*/
do
{
ret = nxsem_wait_uninterruptible(&priv->txsem);
/* The only expected error is ECANCELED which would occur if the
* calling thread were canceled.
*/
DEBUGASSERT(ret == OK || ret == -ECANCELED);
}
while (priv->txresult == 0 && ret == OK);
return ret;
}
#endif
/****************************************************************************
* Name: spi_dmarxwakeup
*
* Description:
* Signal that DMA is complete
*
****************************************************************************/
#ifdef CONFIG_STM32H7_SPI_DMA
static inline void spi_dmarxwakeup(struct stm32_spidev_s *priv)
{
nxsem_post(&priv->rxsem);
}
#endif
/****************************************************************************
* Name: spi_dmarxcallback
*
* Description:
* Called when the RX DMA completes
*
****************************************************************************/
#ifdef CONFIG_STM32H7_SPI_DMA
static void spi_dmarxcallback(DMA_HANDLE handle, uint8_t isr, void *arg)
{
struct stm32_spidev_s *priv = (struct stm32_spidev_s *)arg;
/* Wake-up the SPI driver */
priv->rxresult = isr | 0x080; /* OR'ed with 0x80 to assure non-zero */
spi_dmarxwakeup(priv);
}
#endif
/****************************************************************************
* Name: spi_dmarxsetup
*
* Description:
* Setup to perform RX DMA
*
****************************************************************************/
#ifdef CONFIG_STM32H7_SPI_DMA
static void spi_dmarxsetup(struct stm32_spidev_s *priv,
void *rxbuffer, void *rxdummy,
size_t nwords, stm32_dmacfg_t *dmacfg)
{
/* Can't receive in tx only mode */
if (priv->config == SIMPLEX_TX)
{
priv->rxccr = 0;
return;
}
/* 8- or 16-bit mode? */
if (priv->nbits > 8)
{
/* 16-bit mode -- is there a buffer to receive data in? */
if (rxbuffer)
{
priv->rxccr = SPI_RXDMA16_CONFIG;
}
else
{
rxbuffer = rxdummy;
priv->rxccr = SPI_RXDMA16NULL_CONFIG;
}
}
else
{
/* 8-bit mode -- is there a buffer to receive data in? */
if (rxbuffer)
{
priv->rxccr = SPI_RXDMA8_CONFIG;
}
else
{
rxbuffer = rxdummy;
priv->rxccr = SPI_RXDMA8NULL_CONFIG;
}
}
/* Configure the RX DMA */
dmacfg->paddr = priv->spibase + STM32_SPI_RXDR_OFFSET;
dmacfg->maddr = (uint32_t)rxbuffer;
dmacfg->ndata = nwords;
dmacfg->cfg1 = priv->rxccr;
dmacfg->cfg2 = 0;
}
#endif
/****************************************************************************
* Name: spi_dmatxsetup
*
* Description:
* Setup to perform TX DMA
*
****************************************************************************/
#ifdef CONFIG_STM32H7_SPI_DMA
static void spi_dmatxsetup(struct stm32_spidev_s *priv,
const void *txbuffer, const void *txdummy,
size_t nwords, stm32_dmacfg_t *dmacfg)
{
/* Can't transmit in rx only mode */
if (priv->config == SIMPLEX_RX)
{
priv->txccr = 0;
return;
}
/* 8- or 16-bit mode? */
if (priv->nbits > 8)
{
/* 16-bit mode -- is there a buffer to transfer data from? */
if (txbuffer)
{
priv->txccr = SPI_TXDMA16_CONFIG;
}
else
{
txbuffer = txdummy;
priv->txccr = SPI_TXDMA16NULL_CONFIG;
}
}
else
{
/* 8-bit mode -- is there a buffer to transfer data from? */
if (txbuffer)
{
priv->txccr = SPI_TXDMA8_CONFIG;
}
else
{
txbuffer = txdummy;
priv->txccr = SPI_TXDMA8NULL_CONFIG;
}
}
dmacfg->paddr = priv->spibase + STM32_SPI_TXDR_OFFSET;
dmacfg->maddr = (uint32_t)txbuffer;
dmacfg->ndata = nwords;
dmacfg->cfg1 = priv->txccr;
dmacfg->cfg2 = 0;
}
#endif
/****************************************************************************
* Name: spi_dmarxstart
*
* Description:
* Start RX DMA
*
****************************************************************************/
#ifdef CONFIG_STM32H7_SPI_DMA
static void spi_dmarxstart(struct stm32_spidev_s *priv)
{
/* Can't receive in tx only mode */
if (priv->config == SIMPLEX_TX)
{
return;
}
priv->rxresult = 0;
spi_modifyreg(priv, STM32_SPI_CFG1_OFFSET, 0, SPI_CFG1_RXDMAEN);
stm32_dmastart(priv->rxdma, spi_dmarxcallback, priv, false);
}
#endif
/****************************************************************************
* Name: spi_dmatxstart
*
* Description:
* Start TX DMA
*
****************************************************************************/
#ifdef CONFIG_STM32H7_SPI_DMA
static void spi_dmatxstart(struct stm32_spidev_s *priv)
{
/* Can't transmit in rx only mode */
if (priv->config == SIMPLEX_RX)
{
return;
}
priv->txresult = 0;
stm32_dmastart(priv->txdma, NULL, priv, false);
spi_modifyreg(priv, STM32_SPI_CFG1_OFFSET, 0, SPI_CFG1_TXDMAEN);
}
#endif
/****************************************************************************
* Name: spi_lock
*
* Description:
* On SPI buses where there are multiple devices, it will be necessary to
* lock SPI to have exclusive access to the buses for a sequence of
* transfers. The bus should be locked before the chip is selected. After
* locking the SPI bus, the caller should then also call the setfrequency,
* setbits, and setmode methods to make sure that the SPI is properly
* configured for the device. If the SPI bus is being shared, then it
* may have been left in an incompatible state.
*
* Input Parameters:
* dev - Device-specific state data
* lock - true: Lock spi bus, false: unlock SPI bus
*
* Returned Value:
* None
*
****************************************************************************/
static int spi_lock(struct spi_dev_s *dev, bool lock)
{
struct stm32_spidev_s *priv = (struct stm32_spidev_s *)dev;
int ret;
if (lock)
{
ret = nxmutex_lock(&priv->lock);
}
else
{
ret = nxmutex_unlock(&priv->lock);
}
return ret;
}
/****************************************************************************
* Name: spi_enable
****************************************************************************/
static inline int spi_enable(struct stm32_spidev_s *priv, bool state)
{
int ret = OK;
if (state == true)
{
/* Enable SPI */
spi_modifyreg(priv, STM32_SPI_CR1_OFFSET, 0, SPI_CR1_SPE);
}
else
{
/* Disable SPI */
spi_modifyreg(priv, STM32_SPI_CR1_OFFSET, SPI_CR1_SPE, 0);
}
return ret;
}
/****************************************************************************
* Name: spi_setfrequency
*
* Description:
* Set the SPI frequency.
*
* Input Parameters:
* dev - Device-specific state data
* frequency - The SPI frequency requested
*
* Returned Value:
* Returns the actual frequency selected
*
****************************************************************************/
static uint32_t spi_setfrequency(struct spi_dev_s *dev,
uint32_t frequency)
{
struct stm32_spidev_s *priv = (struct stm32_spidev_s *)dev;
uint32_t setbits = 0;
uint32_t actual = 0;
/* Limit to max possible (if STM32_SPI_CLK_MAX is defined in board.h) */
if (frequency > STM32_SPI_CLK_MAX)
{
frequency = STM32_SPI_CLK_MAX;
}
/* Has the frequency changed? */
if (frequency != priv->frequency)
{
/* Choices are limited by PCLK frequency with a set of divisors */
if (frequency >= priv->spiclock >> 1)
{
/* More than fPCLK/2. This is as fast as we can go */
setbits = SPI_CFG1_MBR_FPCLKd2; /* 000: fPCLK/2 */
actual = priv->spiclock >> 1;
}
else if (frequency >= priv->spiclock >> 2)
{
/* Between fPCLCK/2 and fPCLCK/4, pick the slower */
setbits = SPI_CFG1_MBR_FPCLKd4; /* 001: fPCLK/4 */
actual = priv->spiclock >> 2;
}
else if (frequency >= priv->spiclock >> 3)
{
/* Between fPCLCK/4 and fPCLCK/8, pick the slower */
setbits = SPI_CFG1_MBR_FPCLKd8; /* 010: fPCLK/8 */
actual = priv->spiclock >> 3;
}
else if (frequency >= priv->spiclock >> 4)
{
/* Between fPCLCK/8 and fPCLCK/16, pick the slower */
setbits = SPI_CFG1_MBR_FPCLKd16; /* 011: fPCLK/16 */
actual = priv->spiclock >> 4;
}
else if (frequency >= priv->spiclock >> 5)
{
/* Between fPCLCK/16 and fPCLCK/32, pick the slower */
setbits = SPI_CFG1_MBR_FPCLKd32; /* 100: fPCLK/32 */
actual = priv->spiclock >> 5;
}
else if (frequency >= priv->spiclock >> 6)
{
/* Between fPCLCK/32 and fPCLCK/64, pick the slower */
setbits = SPI_CFG1_MBR_FPCLKd64; /* 101: fPCLK/64 */
actual = priv->spiclock >> 6;
}
else if (frequency >= priv->spiclock >> 7)
{
/* Between fPCLCK/64 and fPCLCK/128, pick the slower */
setbits = SPI_CFG1_MBR_FPCLKd128; /* 110: fPCLK/128 */
actual = priv->spiclock >> 7;
}
else
{
/* Less than fPCLK/128. This is as slow as we can go */
setbits = SPI_CFG1_MBR_FPCLKd256; /* 111: fPCLK/256 */
actual = priv->spiclock >> 8;
}
spi_enable(priv, false);
spi_modifyreg(priv, STM32_SPI_CFG1_OFFSET, SPI_CFG1_MBR_MASK, setbits);
spi_enable(priv, true);
/* Save the frequency selection so that subsequent reconfigurations
* will be faster.
*/
spiinfo("Frequency %" PRId32 "->%" PRId32 "\n", frequency, actual);
priv->frequency = frequency;
priv->actual = actual;
}
return priv->actual;
}
/****************************************************************************
* Name: spi_setdelay
*
* Description:
* Set the SPI Delays in nanoseconds. Optional.
*
* Input Parameters:
* dev - Device-specific state data
* startdelay - The delay between CS active and first CLK
* stopdelay - The delay between last CLK and CS inactive
* csdelay - The delay between CS inactive and CS active again
* ifdelay - The delay between frames
*
* Returned Value:
* Returns zero (OK) on success; a negated errno value is return on any
* failure.
*
****************************************************************************/
#ifdef CONFIG_SPI_DELAY_CONTROL
static int spi_setdelay(struct spi_dev_s *dev, uint32_t startdelay,
uint32_t stopdelay, uint32_t csdelay,
uint32_t ifdelay)
{
struct stm32_spidev_s *priv = (struct stm32_spidev_s *)dev;
uint32_t setbits = 0;
uint32_t clrbits = SPI_CFG2_MSSI_MASK | SPI_CFG2_MIDI_MASK;
uint32_t nsperclk = NSEC_PER_SEC / priv->actual;
startdelay /= nsperclk;
ifdelay /= nsperclk;
setbits = ((ifdelay << SPI_CFG2_MIDI_SHIFT) & SPI_CFG2_MIDI_MASK) |
((startdelay << SPI_CFG2_MSSI_SHIFT) & SPI_CFG2_MSSI_MASK);
spi_enable(priv, false);
/* Change SPI mode */
spi_modifyreg(priv, STM32_SPI_CFG2_OFFSET, clrbits, setbits);
/* Re-enable SPI */
spi_enable(priv, true);
return OK;
}
#endif
/****************************************************************************
* Name: spi_setmode
*
* Description:
* Set the SPI mode. see enum spi_mode_e for mode definitions
*
* Input Parameters:
* dev - Device-specific state data
* mode - The SPI mode requested
*
* Returned Value:
* Returns the actual frequency selected
*
****************************************************************************/
static void spi_setmode(struct spi_dev_s *dev, enum spi_mode_e mode)
{
struct stm32_spidev_s *priv = (struct stm32_spidev_s *)dev;
uint32_t setbits = 0;
uint32_t clrbits = 0;
spiinfo("mode=%" PRIx32 "\n", (uint32_t) mode);
/* Has the mode changed? */
if (mode != priv->mode)
{
/* Yes... Set CR1 appropriately */
switch (mode)
{
case SPIDEV_MODE0: /* CPOL=0; CPHA=0 */
setbits = 0;
clrbits = SPI_CFG2_CPOL | SPI_CFG2_CPHA;
break;
case SPIDEV_MODE1: /* CPOL=0; CPHA=1 */
setbits = SPI_CFG2_CPHA;
clrbits = SPI_CFG2_CPOL;
break;
case SPIDEV_MODE2: /* CPOL=1; CPHA=0 */
setbits = SPI_CFG2_CPOL;
clrbits = SPI_CFG2_CPHA;
break;
case SPIDEV_MODE3: /* CPOL=1; CPHA=1 */
setbits = SPI_CFG2_CPOL | SPI_CFG2_CPHA;
clrbits = 0;
break;
default:
return;
}
spi_enable(priv, false);
/* Change SPI mode */
spi_modifyreg(priv, STM32_SPI_CFG2_OFFSET, clrbits, setbits);
/* Re-enable SPI */
spi_enable(priv, true);
while ((spi_getreg(priv, STM32_SPI_SR_OFFSET) &
SPI_SR_RXPLVL_MASK) != 0)
{
/* Flush SPI read FIFO */
spi_getreg(priv, STM32_SPI_RXDR_OFFSET);
}
/* Save the mode so that subsequent re-configurations will be faster */
priv->mode = mode;
}
}
/****************************************************************************
* Name: spi_setbits
*
* Description:
* Set the number of bits per word.
*
* Input Parameters:
* dev - Device-specific state data
* nbits - The number of bits requested
*
* Returned Value:
* None
*
****************************************************************************/
static void spi_setbits(struct spi_dev_s *dev, int nbits)
{
struct stm32_spidev_s *priv = (struct stm32_spidev_s *)dev;
uint32_t setbits = 0;
uint32_t clrbits = 0;
spiinfo("nbits=%d\n", nbits);
/* Has the number of bits changed? */
if (nbits != priv->nbits)
{
/* Yes... Set CFG1 appropriately */
/* Set the number of bits (valid range 4-32) */
if (nbits < 4 || nbits > 32)
{
return;
}
clrbits = SPI_CFG1_DSIZE_MASK;
setbits = SPI_CFG1_DSIZE_VAL(nbits);
/* RX FIFO Threshold 1 Frame either 8 or 16 bits */
setbits |= SPI_CFG1_FTHLV_1DATA;
spi_enable(priv, false);
spi_modifyreg(priv, STM32_SPI_CFG1_OFFSET, clrbits, setbits);
spi_enable(priv, true);
/* Save the selection so that subsequent re-configurations will be
* faster.
*/
priv->nbits = nbits;
}
}
/****************************************************************************
* Name: spi_hwfeatures
*
* Description:
* Set hardware-specific feature flags.
*
* Input Parameters:
* dev - Device-specific state data
* features - H/W feature flags
*
* Returned Value:
* Zero (OK) if the selected H/W features are enabled; A negated errno
* value if any H/W feature is not supportable.
*
****************************************************************************/
#ifdef CONFIG_SPI_HWFEATURES
static int spi_hwfeatures(struct spi_dev_s *dev,
spi_hwfeatures_t features)
{
#if defined(CONFIG_SPI_BITORDER) || defined(CONFIG_SPI_TRIGGER)
struct stm32_spidev_s *priv = (struct stm32_spidev_s *)dev;
#endif
#ifdef CONFIG_SPI_BITORDER
uint32_t setbits = 0;
uint32_t clrbits = 0;
spiinfo("features=%08" PRIx8 "\n", features);
/* Transfer data LSB first? */
if ((features & HWFEAT_LSBFIRST) != 0)
{
setbits = SPI_CFG2_LSBFRST;
clrbits = 0;
}
else
{
setbits = 0;
clrbits = SPI_CFG2_LSBFRST;
}
spi_enable(priv, false);
spi_modifyreg(priv, STM32_SPI_CFG2_OFFSET, clrbits, setbits);
spi_enable(priv, true);
features &= ~HWFEAT_LSBFIRST;
#endif
#ifdef CONFIG_SPI_TRIGGER
/* Turn deferred trigger mode on or off. Only applicable for DMA mode. If a
* transfer is deferred then the DMA will not actually be triggered until a
* subsequent call to SPI_TRIGGER to set it off. The thread will be waiting
* on the transfer completing as normal.
*/
priv->defertrig = ((features & HWFEAT_TRIGGER) != 0);
features &= ~HWFEAT_TRIGGER;
#endif
/* Other H/W features are not supported */
return (features == 0) ? OK : -ENOSYS;
}
#endif
/****************************************************************************
* Name: spi_send
*
* Description:
* Exchange one word on SPI
*
* Input Parameters:
* dev - Device-specific state data
* wd - The word to send. the size of the data is determined by the
* number of bits selected for the SPI interface.
*
* Returned Value:
* response
*
****************************************************************************/
static uint32_t spi_send(struct spi_dev_s *dev, uint32_t wd)
{
struct stm32_spidev_s *priv = (struct stm32_spidev_s *)dev;
uint32_t regval = 0;
uint32_t ret = 0;
DEBUGASSERT(priv && priv->spibase);
/* Clear suspend flag */
spi_modifyreg(priv, STM32_SPI_IFCR_OFFSET, 0, SPI_IFCR_SUSPC);
/* Master transfer start */
if (priv->config != SIMPLEX_RX)
{
spi_modifyreg(priv, STM32_SPI_CR1_OFFSET, 0, SPI_CR1_CSTART);
}
/* According to the number of bits, access data register as word or byte
* This is absolutely required because of packing. With nbits <=8 bit
* frames, two bytes are received by a 16-bit read of the data register!
*/
if (priv->nbits > 8)
{
spi_writeword(priv, (uint16_t)(wd & 0xffff));
ret = spi_readword(priv);
}
else
{
spi_writebyte(priv, (uint8_t)(wd & 0xff));
ret = (uint32_t)spi_readbyte(priv);
}
/* Check and clear any error flags (Reading from the SR clears the error
* flags).
*/
regval = spi_getreg(priv, STM32_SPI_SR_OFFSET);
/* Suspend */
spi_modifyreg(priv, STM32_SPI_CR1_OFFSET, 0, SPI_CR1_CSUSP);
while ((spi_getreg(priv, STM32_SPI_SR_OFFSET) & SPI_SR_SUSP) == 0);
/* Dump some info */
if (priv->nbits > 8)
{
spiinfo("Sent: %04" PRIx32 " Return: %04" PRIx32 " Status: %02" PRIx32
"\n", wd, ret, regval);
}
else
{
spiinfo("Sent: %02" PRIx32 " Return: %02" PRIx32 " Status: %02" PRIx32
"\n", wd, ret, regval);
}
UNUSED(regval);
return ret;
}
/****************************************************************************
* Name: spi_exchange (no DMA). aka spi_exchange_nodma
*
* Description:
* Exchange a block of data on SPI without using DMA
*
* Input Parameters:
* dev - Device-specific state data
* txbuffer - A pointer to the buffer of data to be sent
* rxbuffer - A pointer to a buffer in which to receive data
* nwords - the length of data to be exchanged in units of words.
* The wordsize is determined by the number of bits-per-word
* selected for the SPI interface. If nbits <= 8, the data is
* packed into uint8_t's; if nbits >8, the data is packed into
* uint16_t's
*
* Returned Value:
* None
*
****************************************************************************/
#if !defined(CONFIG_STM32H7_SPI_DMA) || defined(CONFIG_STM32H7_DMACAPABLE) || \
defined(CONFIG_STM32H7_SPI_DMATHRESHOLD)
#if !defined(CONFIG_STM32H7_SPI_DMA)
static void spi_exchange(struct spi_dev_s *dev, const void *txbuffer,
void *rxbuffer, size_t nwords)
#else
static void spi_exchange_nodma(struct spi_dev_s *dev,
const void *txbuffer, void *rxbuffer,
size_t nwords)
#endif
{
struct stm32_spidev_s *priv = (struct stm32_spidev_s *)dev;
DEBUGASSERT(priv && priv->spibase);
spiinfo("txbuffer=%p rxbuffer=%p nwords=%d\n", txbuffer, rxbuffer, nwords);
/* Disable the DMA Requests */
spi_modifyreg(priv, STM32_SPI_CFG1_OFFSET, SPI_CFG1_RXDMAEN |
SPI_CFG1_TXDMAEN, 0);
/* 8- or 16-bit mode? */
if (priv->nbits > 8)
{
/* 16-bit mode */
const uint16_t *src = (const uint16_t *)txbuffer;
uint16_t *dest = (uint16_t *)rxbuffer;
uint16_t word;
while (nwords-- > 0)
{
/* Get the next word to write. Is there a source buffer? */
if (src)
{
word = *src++;
}
else
{
word = 0xffff;
}
/* Exchange one word */
word = (uint16_t)spi_send(dev, (uint32_t)word);
/* Is there a buffer to receive the return value? */
if (dest)
{
*dest++ = word;
}
}
}
else
{
/* 8-bit mode */
const uint8_t *src = (const uint8_t *)txbuffer;
uint8_t *dest = (uint8_t *)rxbuffer;
uint8_t word;
while (nwords-- > 0)
{
/* Get the next word to write. Is there a source buffer? */
if (src)
{
word = *src++;
}
else
{
word = 0xff;
}
/* Exchange one word */
word = (uint8_t)spi_send(dev, (uint32_t)word);
/* Is there a buffer to receive the return value? */
if (dest)
{
*dest++ = word;
}
}
}
}
#endif /* !CONFIG_STM32H7_SPI_DMA || CONFIG_STM32H7_DMACAPABLE ||
* CONFIG_STM32H7_SPI_DMATHRESHOLD
*/
/****************************************************************************
* Name: spi_exchange (with DMA capability)
*
* Description:
* Exchange a block of data on SPI using DMA
*
* Input Parameters:
* dev - Device-specific state data
* txbuffer - A pointer to the buffer of data to be sent
* rxbuffer - A pointer to a buffer in which to receive data
* nwords - the length of data to be exchanged in units of words.
* The wordsize is determined by the number of bits-per-word
* selected for the SPI interface. If nbits <= 8, the data is
* packed into uint8_t's; if nbits >8, the data is packed into
* uint16_t's
*
* Returned Value:
* None
*
****************************************************************************/
#ifdef CONFIG_STM32H7_SPI_DMA
static void spi_exchange(struct spi_dev_s *dev, const void *txbuffer,
void *rxbuffer, size_t nwords)
{
struct stm32_spidev_s *priv = (struct stm32_spidev_s *)dev;
stm32_dmacfg_t rxdmacfg;
stm32_dmacfg_t txdmacfg;
static uint8_t rxdummy[ARMV7M_DCACHE_LINESIZE]
aligned_data(ARMV7M_DCACHE_LINESIZE);
static const uint16_t txdummy = 0xffff;
void *orig_rxbuffer = rxbuffer;
DEBUGASSERT(priv != NULL);
/* Convert the number of word to a number of bytes */
size_t nbytes = (priv->nbits > 8) ? nwords << 1 : nwords;
#ifdef CONFIG_STM32H7_SPI_DMATHRESHOLD
/* If this is a small SPI transfer, then let spi_exchange_nodma() do the
* work.
*/
if (nbytes <= CONFIG_STM32H7_SPI_DMATHRESHOLD)
{
spi_exchange_nodma(dev, txbuffer, rxbuffer, nwords);
return;
}
#endif
if ((priv->config != SIMPLEX_TX && priv->rxdma == NULL) ||
(priv->config != SIMPLEX_RX && priv->txdma == NULL) ||
up_interrupt_context())
{
/* Invalid DMA channels, or interrupt context, fall
* back to non-DMA method.
*/
spi_exchange_nodma(dev, txbuffer, rxbuffer, nwords);
return;
}
/* If this bus uses the driver's DMA aligned buffers (priv->txbuf != NULL)
* we will incur 2 copies. However the copy cost is much less the non
* DMA transfer time. Having the buffer in the driver ensures DMA can be
* used. This is needed because the stm32_dmacapable API does not support
* passing the buffer extent. So the only extent calculated is buffer
* plus the transfer size. The sizes can be less than a cache line size,
* and not aligned and are typically greater then 4 bytes, which is
* about the break even point for the DMA IO overhead.
*/
/* Does bus support in driver DMA buffering? */
if (priv->txbuf)
{
if (nbytes > priv->buflen)
{
/* Buffer is too big for internal DMA buffer so fall back. */
spi_exchange_nodma(dev, txbuffer, rxbuffer, nwords);
return;
}
/* First copy: If provided, copy caller's buffer to the internal DMA
* txbuf
*/
if (txbuffer)
{
memcpy(priv->txbuf, txbuffer, nbytes);
/* Adjust pointers to internal DMA buffers */
txbuffer = priv->txbuf;
}
/* orig_rxbuffer holds the callers return buffer */
rxbuffer = rxbuffer ? priv->rxbuf : rxbuffer;
}
/* Setup the DMA configs using the internal or external set of buffers */
spi_dmatxsetup(priv, txbuffer, &txdummy, nwords, &txdmacfg);
spi_dmarxsetup(priv, rxbuffer, (uint16_t *)rxdummy, nwords, &rxdmacfg);
#ifdef CONFIG_STM32H7_DMACAPABLE
/* Test for DMA capability of only callers buffers, internal buffers are
* guaranteed capable.
*/
if ((priv->config != SIMPLEX_RX && priv->txbuf == 0 &&
!stm32_dmacapable(priv->txdma, &txdmacfg)) ||
(priv->config != SIMPLEX_TX && priv->rxbuf == 0 &&
!stm32_dmacapable(priv->rxdma, &rxdmacfg)))
{
/* Unsupported memory region fall back to non-DMA method. */
spi_exchange_nodma(dev, txbuffer, rxbuffer, nwords);
}
else
#endif
{
/* When starting communication using DMA, to prevent DMA channel
* management raising error events, these steps must be followed in
* order:
* 1. Enable DMA Rx buffer in the RXDMAEN bit in the SPI_CFG1 register,
* if DMA Rx is used.
* 2. Enable DMA requests for Tx and Rx in DMA registers, if the DMA is
* used.
* 3. Enable DMA Tx buffer in the TXDMAEN bit in the SPI_CFG1 register,
* if DMA Tx is used.
* 4. Enable the SPI by setting the SPE bit.
*/
/* Flush cache to physical memory */
if (txbuffer)
{
up_clean_dcache((uintptr_t)txbuffer, (uintptr_t)txbuffer + nbytes);
}
if (rxbuffer)
{
up_invalidate_dcache((uintptr_t)rxbuffer,
(uintptr_t)rxbuffer + nbytes);
}
/* N.B. the H7 tri-states the clock output on SPI disable and
* unfortunately the Chip Select (CS) is active. So we keep
* the device disabled for the minimum time, that meets the
* setup sequence criteria.
*/
spi_enable(priv, false);
spiinfo("txbuffer=%p rxbuffer=%p nwords=%d\n",
txbuffer, rxbuffer, nwords);
DEBUGASSERT(priv->spibase != 0);
/* Setup the DMA */
if (priv->config != SIMPLEX_TX)
{
stm32_dmasetup(priv->rxdma, &rxdmacfg);
}
if (priv->config != SIMPLEX_RX)
{
stm32_dmasetup(priv->txdma, &txdmacfg);
}
#ifdef CONFIG_SPI_TRIGGER
/* Is deferred triggering in effect? */
if (!priv->defertrig)
{
/* No.. Start the DMAs then the SPI */
spi_dmarxstart(priv);
spi_dmatxstart(priv);
spi_enable(priv, true);
spi_modifyreg(priv, STM32_SPI_CR1_OFFSET, 0, SPI_CR1_CSTART);
}
else
{
/* Yes.. indicated that we are ready to be started */
priv->trigarmed = true;
}
#else
/* Start the DMAs then the SPI */
spi_dmarxstart(priv);
spi_dmatxstart(priv);
spi_enable(priv, true);
spi_modifyreg(priv, STM32_SPI_CR1_OFFSET, 0, SPI_CR1_CSTART);
#endif
/* Then wait for each to complete */
spi_dmarxwait(priv);
spi_dmatxwait(priv);
/* To close communication it is mandatory to follow these steps in
* this order:
* 1. Disable DMA request for Tx and Rx in the DMA registers, if the
* DMA issued.
* 2. Disable the SPI by following the SPI disable procedure.
* 3. Disable DMA Tx and Rx buffers by clearing the TXDMAEN and RXDMAEN
* bits in the SPI_CFG1 register, if DMA Tx and/or DMA Rx are used.
*/
/* TX transmission must be completed before shutting down the SPI */
DEBUGASSERT(priv->config != SIMPLEX_RX ?
(spi_getreg(priv, STM32_SPI_SR_OFFSET) & SPI_SR_TXC) : 1);
spi_enable(priv, false);
spi_modifyreg(priv, STM32_SPI_CFG1_OFFSET, SPI_CFG1_TXDMAEN |
SPI_CFG1_RXDMAEN, 0);
spi_enable(priv, true);
/* Second copy: Copy the DMA internal buffer to caller's buffer */
if (orig_rxbuffer && priv->rxbuf)
{
memcpy(orig_rxbuffer, priv->rxbuf, nbytes);
}
}
#ifdef CONFIG_SPI_TRIGGER
priv->trigarmed = false;
#endif
}
#endif /* CONFIG_STM32H7_SPI_DMA */
/****************************************************************************
* Name: spi_trigger
*
* Description:
* Trigger a previously configured DMA transfer.
*
* Input Parameters:
* dev - Device-specific state data
*
* Returned Value:
* OK - Trigger was fired
* ENOTSUP - Trigger not fired due to lack of DMA support
* EIO - Trigger not fired because not previously primed
*
****************************************************************************/
#ifdef CONFIG_SPI_TRIGGER
static int spi_trigger(struct spi_dev_s *dev)
{
#ifdef CONFIG_STM32H7_SPI_DMA
struct stm32_spidev_s *priv = (struct stm32_spidev_s *)dev;
if (!priv->trigarmed)
{
return -EIO;
}
spi_dmarxstart(priv);
spi_dmatxstart(priv);
spi_enable(priv, true);
spi_modifyreg(priv, STM32_SPI_CR1_OFFSET, 0, SPI_CR1_CSTART);
return OK;
#else
return -ENOSYS;
#endif
}
#endif
/****************************************************************************
* Name: spi_sndblock
*
* Description:
* Send a block of data on SPI
*
* Input Parameters:
* dev - Device-specific state data
* txbuffer - A pointer to the buffer of data to be sent
* nwords - the length of data to send from the buffer in number of
* words. The wordsize is determined by the number of
* bits-per-word selected for the SPI interface. If nbits <= 8,
* the data is packed into uint8_t's; if nbits >8, the data is
* packed into uint16_t's
*
* Returned Value:
* None
*
****************************************************************************/
#ifndef CONFIG_SPI_EXCHANGE
static void spi_sndblock(struct spi_dev_s *dev,
const void *txbuffer,
size_t nwords)
{
spiinfo("txbuffer=%p nwords=%d\n", txbuffer, nwords);
return spi_exchange(dev, txbuffer, NULL, nwords);
}
#endif
/****************************************************************************
* Name: spi_recvblock
*
* Description:
* Receive a block of data from SPI
*
* Input Parameters:
* dev - Device-specific state data
* rxbuffer - A pointer to the buffer in which to receive data
* nwords - the length of data that can be received in the buffer in
* number of words. The wordsize is determined by the number of
* bits-per-word selected for the SPI interface. If nbits <= 8,
* the data is packed into uint8_t's; if nbits >8, the data is
* packed into uint16_t's
*
* Returned Value:
* None
*
****************************************************************************/
#ifndef CONFIG_SPI_EXCHANGE
static void spi_recvblock(struct spi_dev_s *dev,
void *rxbuffer,
size_t nwords)
{
spiinfo("rxbuffer=%p nwords=%d\n", rxbuffer, nwords);
return spi_exchange(dev, NULL, rxbuffer, nwords);
}
#endif
/****************************************************************************
* Name: spi_pm_prepare
*
* Description:
* Request the driver to prepare for a new power state. This is a
* warning that the system is about to enter into a new power state. The
* driver should begin whatever operations that may be required to enter
* power state. The driver may abort the state change mode by returning
* a non-zero value from the callback function.
*
* Input Parameters:
* cb - Returned to the driver. The driver version of the callback
* structure may include additional, driver-specific state
* data at the end of the structure.
* domain - Identifies the activity domain of the state change
* pmstate - Identifies the new PM state
*
* Returned Value:
* 0 (OK) means the event was successfully processed and that the driver
* is prepared for the PM state change. Non-zero means that the driver
* is not prepared to perform the tasks needed achieve this power setting
* and will cause the state change to be aborted. NOTE: The prepare
* method will also be recalled when reverting from lower back to higher
* power consumption modes (say because another driver refused a lower
* power state change). Drivers are not permitted to return non-zero
* values when reverting back to higher power consumption modes!
*
****************************************************************************/
#ifdef CONFIG_PM
static int spi_pm_prepare(struct pm_callback_s *cb, int domain,
enum pm_state_e pmstate)
{
struct stm32_spidev_s *priv =
(struct stm32_spidev_s *)((char *)cb -
offsetof(struct stm32_spidev_s, pm_cb));
/* Logic to prepare for a reduced power state goes here. */
switch (pmstate)
{
case PM_NORMAL:
case PM_IDLE:
break;
case PM_STANDBY:
case PM_SLEEP:
/* Check if exclusive lock for SPI bus is held. */
if (nxmutex_is_locked(&priv->lock))
{
/* Exclusive lock is held, do not allow entry to deeper PM
* states.
*/
return -EBUSY;
}
break;
default:
/* Should not get here */
break;
}
return OK;
}
#endif
/****************************************************************************
* Name: spi_bus_initialize
*
* Description:
* Initialize the selected SPI bus in its default state (Master, 8-bit,
* mode 0, etc.)
*
* Input Parameters:
* priv - private SPI device structure
*
* Returned Value:
* None
*
****************************************************************************/
static void spi_bus_initialize(struct stm32_spidev_s *priv)
{
uint32_t setbits = 0;
uint32_t clrbits = 0;
#ifdef CONFIG_PM
int ret;
#endif
/* Configure CR1, CFG1 and CFG2. Default configuration:
* Mode 0: CFG2.CPHA=0 and CFG2.CPOL=0
* Master: CFG2.MSTR=1
* 8-bit: CFG1.DSIZE=7
* MSB transmitted first: CFG2.LSBFRST=0
* Replace NSS with SSI & SSI=1: CR1.SSI=1 CFG2.SSM=1 (prevents MODF
* error)
* Two lines full duplex: CFG2.COMM=0
*/
/* CR1 */
clrbits = SPI_CR1_SPE;
setbits = SPI_CR1_SSI;
spi_modifyreg(priv, STM32_SPI_CR1_OFFSET, clrbits, setbits);
/* CFG1 */
clrbits = SPI_CFG1_DSIZE_MASK;
setbits = SPI_CFG1_DSIZE_8BIT | SPI_CFG1_FTHLV_1DATA; /* REVISIT: FTHLV */
spi_modifyreg(priv, STM32_SPI_CFG1_OFFSET, clrbits, setbits);
/* CFG2 */
clrbits = SPI_CFG2_CPHA | SPI_CFG2_CPOL | SPI_CFG2_LSBFRST |
SPI_CFG2_COMM_MASK;
setbits = SPI_CFG2_AFCNTR | SPI_CFG2_MASTER | SPI_CFG2_SSM;
switch (priv->config)
{
default:
case FULL_DUPLEX:
setbits |= SPI_CFG2_COMM_FULL;
break;
case SIMPLEX_TX:
setbits |= SPI_CFG2_COMM_STX;
break;
case SIMPLEX_RX:
setbits |= SPI_CFG2_COMM_SRX;
break;
case HALF_DUPLEX:
setbits |= SPI_CFG2_COMM_HALF;
break;
}
spi_modifyreg(priv, STM32_SPI_CFG2_OFFSET, clrbits, setbits);
priv->frequency = 0;
priv->nbits = 8;
priv->mode = SPIDEV_MODE0;
/* Select a default frequency of approx. 400KHz */
spi_setfrequency((struct spi_dev_s *)priv, 400000);
/* CRCPOLY configuration */
spi_putreg(priv, STM32_SPI_CRCPOLY_OFFSET, 7);
#ifdef CONFIG_STM32H7_SPI_DMA
/* Get DMA channels. NOTE: stm32_dmachannel() will always assign the DMA
* channel. If the channel is not available, then stm32_dmachannel() will
* block and wait until the channel becomes available. WARNING: If you
* have another device sharing a DMA channel with SPI and the code never
* releases that channel, then the call to stm32_dmachannel() will hang
* forever in this function! Don't let your design do that!
*/
priv->rxdma = NULL;
priv->txdma = NULL;
if (priv->config != SIMPLEX_TX)
{
priv->rxdma = stm32_dmachannel(priv->rxch);
DEBUGASSERT(priv->rxdma);
spi_modifyreg(priv, STM32_SPI_CFG1_OFFSET, 0, SPI_CFG1_RXDMAEN);
}
if (priv->config != SIMPLEX_RX)
{
priv->txdma = stm32_dmachannel(priv->txch);
DEBUGASSERT(priv->txdma);
spi_modifyreg(priv, STM32_SPI_CFG1_OFFSET, 0, SPI_CFG1_TXDMAEN);
}
#endif
/* Attach the IRQ to the driver */
if (irq_attach(priv->spiirq, spi_interrupt, priv))
{
/* We could not attach the ISR to the interrupt */
spierr("ERROR: Can't initialize spi irq\n");
return;
}
/* Enable SPI interrupts */
up_enable_irq(priv->spiirq);
/* Enable SPI */
spi_enable(priv, true);
#ifdef CONFIG_PM
/* Register to receive power management callbacks */
ret = pm_register(&priv->pm_cb);
DEBUGASSERT(ret == OK);
UNUSED(ret);
#endif
#ifdef CONFIG_DEBUG_SPI_INFO
/* Dump registers after initialization */
spi_dumpregs(priv);
#endif
}
/****************************************************************************
* Public Functions
****************************************************************************/
/****************************************************************************
* Name: stm32_spibus_initialize
*
* Description:
* Initialize the selected SPI bus
*
* Input Parameters:
* Port number (for hardware that has multiple SPI interfaces)
*
* Returned Value:
* Valid SPI device structure reference on success; a NULL on failure
*
****************************************************************************/
struct spi_dev_s *stm32_spibus_initialize(int bus)
{
struct stm32_spidev_s *priv = NULL;
irqstate_t flags = enter_critical_section();
#ifdef CONFIG_STM32H7_SPI1
if (bus == 1)
{
/* Select SPI1 */
priv = &g_spi1dev;
/* Only configure if the bus is not already configured */
if (!priv->initialized)
{
/* Configure SPI1 pins: SCK, MISO, and MOSI */
stm32_configgpio(GPIO_SPI1_SCK);
stm32_configgpio(GPIO_SPI1_MISO);
stm32_configgpio(GPIO_SPI1_MOSI);
/* Set up default configuration: Master, 8-bit, etc. */
spi_bus_initialize(priv);
priv->initialized = true;
}
}
else
#endif
#ifdef CONFIG_STM32H7_SPI2
if (bus == 2)
{
/* Select SPI2 */
priv = &g_spi2dev;
/* Only configure if the bus is not already configured */
if (!priv->initialized)
{
/* Configure SPI2 pins: SCK, MISO, and MOSI */
stm32_configgpio(GPIO_SPI2_SCK);
stm32_configgpio(GPIO_SPI2_MISO);
stm32_configgpio(GPIO_SPI2_MOSI);
/* Set up default configuration: Master, 8-bit, etc. */
spi_bus_initialize(priv);
priv->initialized = true;
}
}
else
#endif
#ifdef CONFIG_STM32H7_SPI3
if (bus == 3)
{
/* Select SPI3 */
priv = &g_spi3dev;
/* Only configure if the bus is not already configured */
if (!priv->initialized)
{
/* Configure SPI3 pins: SCK, MISO, and MOSI */
stm32_configgpio(GPIO_SPI3_SCK);
stm32_configgpio(GPIO_SPI3_MISO);
stm32_configgpio(GPIO_SPI3_MOSI);
/* Set up default configuration: Master, 8-bit, etc. */
spi_bus_initialize(priv);
priv->initialized = true;
}
}
else
#endif
#ifdef CONFIG_STM32H7_SPI4
if (bus == 4)
{
/* Select SPI4 */
priv = &g_spi4dev;
/* Only configure if the bus is not already configured */
if (!priv->initialized)
{
/* Configure SPI4 pins: SCK, MISO, and MOSI */
stm32_configgpio(GPIO_SPI4_SCK);
stm32_configgpio(GPIO_SPI4_MISO);
stm32_configgpio(GPIO_SPI4_MOSI);
/* Set up default configuration: Master, 8-bit, etc. */
spi_bus_initialize(priv);
priv->initialized = true;
}
}
else
#endif
#ifdef CONFIG_STM32H7_SPI5
if (bus == 5)
{
/* Select SPI5 */
priv = &g_spi5dev;
/* Only configure if the bus is not already configured */
if (!priv->initialized)
{
/* Configure SPI5 pins: SCK, MISO, and MOSI */
stm32_configgpio(GPIO_SPI5_SCK);
stm32_configgpio(GPIO_SPI5_MISO);
stm32_configgpio(GPIO_SPI5_MOSI);
/* Set up default configuration: Master, 8-bit, etc. */
spi_bus_initialize(priv);
priv->initialized = true;
}
}
else
#endif
#ifdef CONFIG_STM32H7_SPI6
if (bus == 6)
{
/* Select SPI6 */
priv = &g_spi6dev;
/* Only configure if the bus is not already configured */
if (!priv->initialized)
{
/* Configure SPI6 pins: SCK, MISO, and MOSI */
stm32_configgpio(GPIO_SPI6_SCK);
stm32_configgpio(GPIO_SPI6_MISO);
stm32_configgpio(GPIO_SPI6_MOSI);
/* Set up default configuration: Master, 8-bit, etc. */
spi_bus_initialize(priv);
priv->initialized = true;
}
}
else
#endif
{
spierr("ERROR: Unsupported SPI bus: %d\n", bus);
}
leave_critical_section(flags);
return (struct spi_dev_s *)priv;
}
#endif /* CONFIG_STM32H7_SPI1 || CONFIG_STM32H7_SPI2 || CONFIG_STM32H7_SPI3 ||
* CONFIG_STM32H7_SPI4 || CONFIG_STM32H7_SPI5 || CONFIG_STM32H7_SPI6
*/