| /* |
| * Licensed to the Apache Software Foundation (ASF) under one |
| * or more contributor license agreements. See the NOTICE file |
| * distributed with this work for additional information |
| * regarding copyright ownership. The ASF licenses this file |
| * to you under the Apache License, Version 2.0 (the |
| * "License"); you may not use this file except in compliance |
| * with the License. You may obtain a copy of the License at |
| * |
| * http://www.apache.org/licenses/LICENSE-2.0 |
| * |
| * Unless required by applicable law or agreed to in writing, |
| * software distributed under the License is distributed on an |
| * "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY |
| * KIND, either express or implied. See the License for the |
| * specific language governing permissions and limitations |
| * under the License. |
| */ |
| |
| #ifndef H_BLE_HCI_COMMON_ |
| #define H_BLE_HCI_COMMON_ |
| |
| #include "ble.h" |
| |
| #ifdef __cplusplus |
| extern "C" { |
| #endif |
| |
| /* |
| * HCI Command Header |
| * |
| * Comprises the following fields |
| * -> Opcode group field & Opcode command field (2) |
| * -> Parameter Length (1) |
| * Length of all the parameters (does not include any part of the hci |
| * command header |
| */ |
| #define BLE_HCI_CMD_HDR_LEN (3) |
| |
| #define BLE_HCI_OPCODE_NOP (0) |
| |
| /* Set opcode based on OCF and OGF */ |
| #define BLE_HCI_OP(ogf, ocf) ((ocf) | ((ogf) << 10)) |
| |
| /* Get the OGF and OCF from the opcode in the command */ |
| #define BLE_HCI_OGF(opcode) (((opcode) >> 10) & 0x003F) |
| #define BLE_HCI_OCF(opcode) ((opcode) & 0x03FF) |
| |
| /* Opcode Group definitions (note: 0x07 not defined in spec) */ |
| #define BLE_HCI_OGF_LINK_CTRL (0x01) |
| #define BLE_HCI_OGF_LINK_POLICY (0x02) |
| #define BLE_HCI_OGF_CTLR_BASEBAND (0x03) |
| #define BLE_HCI_OGF_INFO_PARAMS (0x04) |
| #define BLE_HCI_OGF_STATUS_PARAMS (0x05) |
| #define BLE_HCI_OGF_TESTING (0x06) |
| #define BLE_HCI_OGF_LE (0x08) |
| #define BLE_HCI_OGF_VENDOR (0x3F) |
| |
| /* |
| * Number of LE commands. NOTE: this is really just used to size the array |
| * containing the lengths of the LE commands. |
| */ |
| #define BLE_HCI_NUM_LE_CMDS (79) |
| |
| /* List of OCF for Link Control commands (OGF=0x01) */ |
| #define BLE_HCI_OCF_DISCONNECT_CMD (0x0006) |
| #define BLE_HCI_OCF_RD_REM_VER_INFO (0x001D) |
| |
| /* List of OCF for Controller and Baseband commands (OGF=0x03) */ |
| #define BLE_HCI_OCF_CB_SET_EVENT_MASK (0x0001) |
| #define BLE_HCI_OCF_CB_RESET (0x0003) |
| #define BLE_HCI_OCF_CB_READ_TX_PWR (0x002D) |
| #define BLE_HCI_OCF_CB_SET_CTLR_TO_HOST_FC (0x0031) |
| #define BLE_HCI_OCF_CB_HOST_BUF_SIZE (0x0033) |
| #define BLE_HCI_OCF_CB_HOST_NUM_COMP_PKTS (0x0035) |
| #define BLE_HCI_OCF_CB_SET_EVENT_MASK2 (0x0063) |
| #define BLE_HCI_OCF_CB_RD_AUTH_PYLD_TMO (0x007B) |
| #define BLE_HCI_OCF_CB_WR_AUTH_PYLD_TMO (0x007C) |
| |
| /* List of OCF for Info Param commands (OGF=0x04) */ |
| #define BLE_HCI_OCF_IP_RD_LOCAL_VER (0x0001) |
| #define BLE_HCI_OCF_IP_RD_LOC_SUPP_CMD (0x0002) |
| #define BLE_HCI_OCF_IP_RD_LOC_SUPP_FEAT (0x0003) |
| #define BLE_HCI_OCF_IP_RD_BUF_SIZE (0x0005) |
| #define BLE_HCI_OCF_IP_RD_BD_ADDR (0x0009) |
| |
| /* List of OCF for Status parameters commands (OGF = 0x05) */ |
| #define BLE_HCI_OCF_RD_RSSI (0x0005) |
| |
| /* List of OCF for LE commands (OGF = 0x08) */ |
| #define BLE_HCI_OCF_LE_SET_EVENT_MASK (0x0001) |
| #define BLE_HCI_OCF_LE_RD_BUF_SIZE (0x0002) |
| #define BLE_HCI_OCF_LE_RD_LOC_SUPP_FEAT (0x0003) |
| /* NOTE: 0x0004 is intentionally left undefined */ |
| #define BLE_HCI_OCF_LE_SET_RAND_ADDR (0x0005) |
| #define BLE_HCI_OCF_LE_SET_ADV_PARAMS (0x0006) |
| #define BLE_HCI_OCF_LE_RD_ADV_CHAN_TXPWR (0x0007) |
| #define BLE_HCI_OCF_LE_SET_ADV_DATA (0x0008) |
| #define BLE_HCI_OCF_LE_SET_SCAN_RSP_DATA (0x0009) |
| #define BLE_HCI_OCF_LE_SET_ADV_ENABLE (0x000A) |
| #define BLE_HCI_OCF_LE_SET_SCAN_PARAMS (0x000B) |
| #define BLE_HCI_OCF_LE_SET_SCAN_ENABLE (0x000C) |
| #define BLE_HCI_OCF_LE_CREATE_CONN (0x000D) |
| #define BLE_HCI_OCF_LE_CREATE_CONN_CANCEL (0x000E) |
| #define BLE_HCI_OCF_LE_RD_WHITE_LIST_SIZE (0x000F) |
| #define BLE_HCI_OCF_LE_CLEAR_WHITE_LIST (0x0010) |
| #define BLE_HCI_OCF_LE_ADD_WHITE_LIST (0x0011) |
| #define BLE_HCI_OCF_LE_RMV_WHITE_LIST (0x0012) |
| #define BLE_HCI_OCF_LE_CONN_UPDATE (0x0013) |
| #define BLE_HCI_OCF_LE_SET_HOST_CHAN_CLASS (0x0014) |
| #define BLE_HCI_OCF_LE_RD_CHAN_MAP (0x0015) |
| #define BLE_HCI_OCF_LE_RD_REM_FEAT (0x0016) |
| #define BLE_HCI_OCF_LE_ENCRYPT (0x0017) |
| #define BLE_HCI_OCF_LE_RAND (0x0018) |
| #define BLE_HCI_OCF_LE_START_ENCRYPT (0x0019) |
| #define BLE_HCI_OCF_LE_LT_KEY_REQ_REPLY (0x001A) |
| #define BLE_HCI_OCF_LE_LT_KEY_REQ_NEG_REPLY (0x001B) |
| #define BLE_HCI_OCF_LE_RD_SUPP_STATES (0x001C) |
| #define BLE_HCI_OCF_LE_RX_TEST (0x001D) |
| #define BLE_HCI_OCF_LE_TX_TEST (0x001E) |
| #define BLE_HCI_OCF_LE_TEST_END (0x001F) |
| #define BLE_HCI_OCF_LE_REM_CONN_PARAM_RR (0x0020) |
| #define BLE_HCI_OCF_LE_REM_CONN_PARAM_NRR (0x0021) |
| #define BLE_HCI_OCF_LE_SET_DATA_LEN (0x0022) |
| #define BLE_HCI_OCF_LE_RD_SUGG_DEF_DATA_LEN (0x0023) |
| #define BLE_HCI_OCF_LE_WR_SUGG_DEF_DATA_LEN (0x0024) |
| #define BLE_HCI_OCF_LE_RD_P256_PUBKEY (0x0025) |
| #define BLE_HCI_OCF_LE_GEN_DHKEY (0x0026) |
| #define BLE_HCI_OCF_LE_ADD_RESOLV_LIST (0x0027) |
| #define BLE_HCI_OCF_LE_RMV_RESOLV_LIST (0x0028) |
| #define BLE_HCI_OCF_LE_CLR_RESOLV_LIST (0x0029) |
| #define BLE_HCI_OCF_LE_RD_RESOLV_LIST_SIZE (0x002A) |
| #define BLE_HCI_OCF_LE_RD_PEER_RESOLV_ADDR (0x002B) |
| #define BLE_HCI_OCF_LE_RD_LOCAL_RESOLV_ADDR (0x002C) |
| #define BLE_HCI_OCF_LE_SET_ADDR_RES_EN (0x002D) |
| #define BLE_HCI_OCF_LE_SET_RPA_TMO (0x002E) |
| #define BLE_HCI_OCF_LE_RD_MAX_DATA_LEN (0x002F) |
| #define BLE_HCI_OCF_LE_RD_PHY (0x0030) |
| #define BLE_HCI_OCF_LE_SET_DEFAULT_PHY (0x0031) |
| #define BLE_HCI_OCF_LE_SET_PHY (0x0032) |
| #define BLE_HCI_OCF_LE_ENH_RX_TEST (0x0033) |
| #define BLE_HCI_OCF_LE_ENH_TX_TEST (0x0034) |
| #define BLE_HCI_OCF_LE_SET_ADV_SET_RND_ADDR (0x0035) |
| #define BLE_HCI_OCF_LE_SET_EXT_ADV_PARAM (0x0036) |
| #define BLE_HCI_OCF_LE_SET_EXT_ADV_DATA (0x0037) |
| #define BLE_HCI_OCF_LE_SET_EXT_SCAN_RSP_DATA (0x0038) |
| #define BLE_HCI_OCF_LE_SET_EXT_ADV_ENABLE (0x0039) |
| #define BLE_HCI_OCF_LE_RD_MAX_ADV_DATA_LEN (0x003A) |
| #define BLE_HCI_OCF_LE_RD_NUM_OF_ADV_SETS (0x003B) |
| #define BLE_HCI_OCF_LE_REMOVE_ADV_SET (0x003C) |
| #define BLE_HCI_OCF_LE_CLEAR_ADV_SETS (0x003D) |
| #define BLE_HCI_OCF_LE_SET_PER_ADV_PARAMS (0x003E) |
| #define BLE_HCI_OCF_LE_SET_PER_ADV_DATA (0x003F) |
| #define BLE_HCI_OCF_LE_SET_PER_ADV_ENABLE (0x0040) |
| #define BLE_HCI_OCF_LE_SET_EXT_SCAN_PARAM (0x0041) |
| #define BLE_HCI_OCF_LE_SET_EXT_SCAN_ENABLE (0x0042) |
| #define BLE_HCI_OCF_LE_EXT_CREATE_CONN (0x0043) |
| #define BLE_HCI_OCF_LE_PER_ADV_CREATE_SYNC (0x0044) |
| #define BLE_HCI_OCF_LE_PER_ADV_CREATE_SYNC_CANCEL (0x0045) |
| #define BLE_HCI_OCF_LE_PER_ADV_TERM_SYNC (0x0046) |
| #define BLE_HCI_OCF_LE_ADD_DEV_TO_PER_ADV_LIST (0x0047) |
| #define BLE_HCI_OCF_LE_REM_DEV_FROM_PER_ADV_LIST (0x0048) |
| #define BLE_HCI_OCF_LE_CLEAR_PER_ADV_LIST (0x0049) |
| #define BLE_HCI_OCF_LE_RD_PER_ADV_LIST_SIZE (0x004A) |
| #define BLE_HCI_OCF_LE_RD_TRANSMIT_POWER (0x004B) |
| #define BLE_HCI_OCF_LE_RD_RF_PATH_COMPENSATION (0x004C) |
| #define BLE_HCI_OCF_LE_WR_RF_PATH_COMPENSATION (0x004D) |
| #define BLE_HCI_OCF_LE_SET_PRIVACY_MODE (0x004E) |
| |
| /* Command Specific Definitions */ |
| #define BLE_HCI_VARIABLE_LEN (0xFF) |
| |
| /* --- Disconnect command (OGF 0x01, OCF 0x0006) --- */ |
| #define BLE_HCI_DISCONNECT_CMD_LEN (3) |
| |
| /* --- Set event mask (OGF 0x03, OCF 0x0001 --- */ |
| #define BLE_HCI_SET_EVENT_MASK_LEN (8) |
| |
| /* --- Set controller to host flow control (OGF 0x03, OCF 0x0031) --- */ |
| #define BLE_HCI_CTLR_TO_HOST_FC_LEN (1) |
| |
| #define BLE_HCI_CTLR_TO_HOST_FC_OFF (0) |
| #define BLE_HCI_CTLR_TO_HOST_FC_ACL (1) |
| #define BLE_HCI_CTLR_TO_HOST_FC_SYNC (2) |
| #define BLE_HCI_CTLR_TO_HOST_FC_BOTH (3) |
| |
| /* --- Host buffer size (OGF 0x03, OCF 0x0033) --- */ |
| #define BLE_HCI_HOST_BUF_SIZE_LEN (7) |
| |
| /* --- Host number of completed packets (OGF 0x03, OCF 0x0035) --- */ |
| #define BLE_HCI_HOST_NUM_COMP_PKTS_HDR_LEN (1) |
| #define BLE_HCI_HOST_NUM_COMP_PKTS_ENT_LEN (4) |
| |
| /* --- Read BD_ADDR (OGF 0x04, OCF 0x0009 --- */ |
| #define BLE_HCI_IP_RD_BD_ADDR_ACK_PARAM_LEN (6) |
| |
| /* --- Read buffer size (OGF 0x04, OCF 0x0005) --- */ |
| #define BLE_HCI_IP_RD_BUF_SIZE_LEN (0) |
| #define BLE_HCI_IP_RD_BUF_SIZE_RSPLEN (7) /* No status byte. */ |
| |
| /* --- Read/Write authenticated payload timeout (ocf 0x007B/0x007C) */ |
| #define BLE_HCI_RD_AUTH_PYLD_TMO_LEN (4) |
| #define BLE_HCI_WR_AUTH_PYLD_TMO_LEN (2) |
| |
| /* --- Read local version information (OGF 0x04, OCF 0x0001) --- */ |
| #define BLE_HCI_RD_LOC_VER_INFO_RSPLEN (8) /* No status byte. */ |
| |
| /* --- Read local supported command (OGF 0x04, OCF 0x0002) --- */ |
| #define BLE_HCI_RD_LOC_SUPP_CMD_RSPLEN (64) /* No status byte. */ |
| |
| /* --- Read local supported features (OGF 0x04, OCF 0x0003) --- */ |
| #define BLE_HCI_RD_LOC_SUPP_FEAT_RSPLEN (8) /* No status byte. */ |
| |
| /* --- Read RSSI (OGF 0x05, OCF 0x0005) --- */ |
| #define BLE_HCI_READ_RSSI_LEN (2) |
| #define BLE_HCI_READ_RSSI_ACK_PARAM_LEN (3) /* No status byte. */ |
| |
| /* --- LE set event mask (OCF 0x0001) --- */ |
| #define BLE_HCI_SET_LE_EVENT_MASK_LEN (8) |
| |
| /* --- LE read buffer size (OCF 0x0002) --- */ |
| #define BLE_HCI_RD_BUF_SIZE_LEN (0) |
| #define BLE_HCI_RD_BUF_SIZE_RSPLEN (3) /* No status byte. */ |
| |
| /* --- LE read local supported features (OCF 0x0003) --- */ |
| #define BLE_HCI_RD_LE_LOC_SUPP_FEAT_RSPLEN (8) /* No status byte. */ |
| |
| /* --- LE set random address (OCF 0x0005) */ |
| #define BLE_HCI_SET_RAND_ADDR_LEN (6) |
| |
| /* --- LE set advertising parameters (OCF 0x0006) */ |
| #define BLE_HCI_SET_ADV_PARAM_LEN (15) |
| |
| /* Advertising types */ |
| #define BLE_HCI_ADV_TYPE_ADV_IND (0) |
| #define BLE_HCI_ADV_TYPE_ADV_DIRECT_IND_HD (1) |
| #define BLE_HCI_ADV_TYPE_ADV_SCAN_IND (2) |
| #define BLE_HCI_ADV_TYPE_ADV_NONCONN_IND (3) |
| #define BLE_HCI_ADV_TYPE_ADV_DIRECT_IND_LD (4) |
| #define BLE_HCI_ADV_TYPE_MAX (4) |
| |
| #define BLE_HCI_ADV_CONN_MASK (0x0001) |
| #define BLE_HCI_ADV_SCAN_MASK (0x0002) |
| #define BLE_HCI_ADV_DIRECT_MASK (0x0004) |
| #define BLE_HCI_ADV_SCAN_RSP_MASK (0x0008) |
| #define BLE_HCI_ADV_LEGACY_MASK (0x0010) |
| |
| #define BLE_HCI_ADV_DATA_STATUS_COMPLETE (0x0000) |
| #define BLE_HCI_ADV_DATA_STATUS_INCOMPLETE (0x0020) |
| #define BLE_HCI_ADV_DATA_STATUS_TRUNCATED (0x0040) |
| #define BLE_HCI_ADV_DATA_STATUS_MASK (0x0060) |
| |
| /* Own address types */ |
| #define BLE_HCI_ADV_OWN_ADDR_PUBLIC (0) |
| #define BLE_HCI_ADV_OWN_ADDR_RANDOM (1) |
| #define BLE_HCI_ADV_OWN_ADDR_PRIV_PUB (2) |
| #define BLE_HCI_ADV_OWN_ADDR_PRIV_RAND (3) |
| #define BLE_HCI_ADV_OWN_ADDR_MAX (3) |
| |
| /* Advertisement peer address Type */ |
| #define BLE_HCI_ADV_PEER_ADDR_PUBLIC (0) |
| #define BLE_HCI_ADV_PEER_ADDR_RANDOM (1) |
| #define BLE_HCI_ADV_PEER_ADDR_MAX (1) |
| |
| /* --- LE advertising channel tx power (OCF 0x0007) */ |
| #define BLE_HCI_ADV_CHAN_TXPWR_ACK_PARAM_LEN (2) /* Includes status byte. */ |
| #define BLE_HCI_ADV_CHAN_TXPWR_MIN (-20) |
| #define BLE_HCI_ADV_CHAN_TXPWR_MAX (10) |
| |
| /* --- LE set advertising data (OCF 0x0008) */ |
| #define BLE_HCI_MAX_ADV_DATA_LEN (31) |
| #define BLE_HCI_SET_ADV_DATA_LEN (32) |
| |
| /* --- LE set scan response data (OCF 0x0009) */ |
| #define BLE_HCI_MAX_SCAN_RSP_DATA_LEN (31) |
| #define BLE_HCI_SET_SCAN_RSP_DATA_LEN (32) |
| |
| /* --- LE set advertising enable (OCF 0x000a) */ |
| #define BLE_HCI_SET_ADV_ENABLE_LEN (1) |
| |
| /* --- LE set scan enable (OCF 0x000c) */ |
| #define BLE_HCI_SET_SCAN_ENABLE_LEN (2) |
| |
| /* Connect peer address type */ |
| #define BLE_HCI_CONN_PEER_ADDR_PUBLIC (0) |
| #define BLE_HCI_CONN_PEER_ADDR_RANDOM (1) |
| #define BLE_HCI_CONN_PEER_ADDR_PUBLIC_IDENT (2) |
| #define BLE_HCI_CONN_PEER_ADDR_RANDOM_IDENT (3) |
| #define BLE_HCI_CONN_PEER_ADDR_MAX (3) |
| |
| /* |
| * Advertising filter policy |
| * |
| * Determines how an advertiser filters scan and connection requests. |
| * |
| * NONE: no filtering (default value). No whitelist used. |
| * SCAN: process all connection requests but only scans from white list. |
| * CONN: process all scan request but only connection requests from white list |
| * BOTH: ignore all scan and connection requests unless in white list. |
| */ |
| #define BLE_HCI_ADV_FILT_NONE (0) |
| #define BLE_HCI_ADV_FILT_SCAN (1) |
| #define BLE_HCI_ADV_FILT_CONN (2) |
| #define BLE_HCI_ADV_FILT_BOTH (3) |
| #define BLE_HCI_ADV_FILT_MAX (3) |
| |
| #define BLE_HCI_ADV_FILT_DEF (BLE_HCI_ADV_FILT_NONE) |
| |
| /* Advertising interval */ |
| #define BLE_HCI_ADV_ITVL (625) /* usecs */ |
| #define BLE_HCI_ADV_ITVL_MIN (32) /* units */ |
| #define BLE_HCI_ADV_ITVL_MAX (16384) /* units */ |
| #define BLE_HCI_ADV_ITVL_NONCONN_MIN (160) /* units */ |
| |
| #define BLE_HCI_ADV_ITVL_DEF (0x800) /* 1.28 seconds */ |
| #define BLE_HCI_ADV_CHANMASK_DEF (0x7) /* all channels */ |
| |
| /* Set scan parameters */ |
| #define BLE_HCI_SET_SCAN_PARAM_LEN (7) |
| #define BLE_HCI_SCAN_TYPE_PASSIVE (0) |
| #define BLE_HCI_SCAN_TYPE_ACTIVE (1) |
| |
| /* Scan interval and scan window timing */ |
| #define BLE_HCI_SCAN_ITVL (625) /* usecs */ |
| #define BLE_HCI_SCAN_ITVL_MIN (4) /* units */ |
| #define BLE_HCI_SCAN_ITVL_MAX (16384) /* units */ |
| #define BLE_HCI_SCAN_ITVL_DEF (16) /* units */ |
| #define BLE_HCI_SCAN_WINDOW_MIN (4) /* units */ |
| #define BLE_HCI_SCAN_WINDOW_MAX (16384) /* units */ |
| #define BLE_HCI_SCAN_WINDOW_DEF (16) /* units */ |
| |
| /* |
| * Scanning filter policy |
| * NO_WL: |
| * Scanner processes all advertising packets (white list not used) except |
| * directed, connectable advertising packets not sent to the scanner. |
| * USE_WL: |
| * Scanner processes advertisements from white list only. A connectable, |
| * directed advertisment is ignored unless it contains scanners address. |
| * NO_WL_INITA: |
| * Scanner process all advertising packets (white list not used). A |
| * connectable, directed advertisement shall not be ignored if the InitA |
| * is a resolvable private address. |
| * USE_WL_INITA: |
| * Scanner process advertisements from white list only. A connectable, |
| * directed advertisement shall not be ignored if the InitA is a |
| * resolvable private address. |
| */ |
| #define BLE_HCI_SCAN_FILT_NO_WL (0) |
| #define BLE_HCI_SCAN_FILT_USE_WL (1) |
| #define BLE_HCI_SCAN_FILT_NO_WL_INITA (2) |
| #define BLE_HCI_SCAN_FILT_USE_WL_INITA (3) |
| #define BLE_HCI_SCAN_FILT_MAX (3) |
| |
| /* Whitelist commands */ |
| #define BLE_HCI_ADD_WHITE_LIST_LEN (7) |
| #define BLE_HCI_RMV_WHITE_LIST_LEN (7) |
| |
| /* Create Connection */ |
| #define BLE_HCI_CREATE_CONN_LEN (25) |
| #define BLE_HCI_CONN_ITVL (1250) /* usecs */ |
| #define BLE_HCI_CONN_FILT_NO_WL (0) |
| #define BLE_HCI_CONN_FILT_USE_WL (1) |
| #define BLE_HCI_CONN_FILT_MAX (1) |
| #define BLE_HCI_CONN_ITVL_MIN (0x0006) |
| #define BLE_HCI_CONN_ITVL_MAX (0x0c80) |
| #define BLE_HCI_CONN_LATENCY_MIN (0x0000) |
| #define BLE_HCI_CONN_LATENCY_MAX (0x01f3) |
| #define BLE_HCI_CONN_SPVN_TIMEOUT_MIN (0x000a) |
| #define BLE_HCI_CONN_SPVN_TIMEOUT_MAX (0x0c80) |
| #define BLE_HCI_CONN_SPVN_TMO_UNITS (10) /* msecs */ |
| #define BLE_HCI_INITIATOR_FILT_POLICY_MAX (1) |
| |
| /* Peer Address Type */ |
| #define BLE_HCI_CONN_PEER_ADDR_PUBLIC (0) |
| #define BLE_HCI_CONN_PEER_ADDR_RANDOM (1) |
| #define BLE_HCI_CONN_PEER_ADDR_PUB_ID (2) |
| #define BLE_HCI_CONN_PEER_ADDR_RAND_ID (3) |
| #define BLE_HCI_CONN_PEER_ADDR_MAX (3) |
| |
| /* --- LE connection update (OCF 0x0013) */ |
| #define BLE_HCI_CONN_UPDATE_LEN (14) |
| |
| /* --- LE set host channel classification command (OCF 0x0014) */ |
| #define BLE_HCI_SET_HOST_CHAN_CLASS_LEN (5) |
| |
| /* --- LE read channel map command (OCF 0x0015) */ |
| #define BLE_HCI_RD_CHANMAP_LEN (2) |
| #define BLE_HCI_RD_CHANMAP_RSP_LEN (7) |
| |
| /* --- LE read remote features (OCF 0x0016) */ |
| #define BLE_HCI_CONN_RD_REM_FEAT_LEN (2) |
| |
| /* --- LE encrypt (OCF 0x0017) */ |
| #define BLE_HCI_LE_ENCRYPT_LEN (32) |
| |
| /* --- LE rand (OCF 0x0018) */ |
| #define BLE_HCI_LE_RAND_LEN (8) |
| |
| /* --- LE start encryption (OCF 0x0019) */ |
| #define BLE_HCI_LE_START_ENCRYPT_LEN (28) |
| |
| /* --- LE long term key request reply command (OCF 0x001a) */ |
| #define BLE_HCI_LT_KEY_REQ_REPLY_LEN (18) |
| #define BLE_HCI_LT_KEY_REQ_REPLY_ACK_PARAM_LEN (2) /* No status byte. */ |
| |
| /* --- LE long term key request negative reply command (OCF 0x001b) */ |
| #define BLE_HCI_LT_KEY_REQ_NEG_REPLY_LEN (2) |
| #define BLE_HCI_LT_KEY_REQ_NEG_REPLY_ACK_PARAM_LEN (2) |
| |
| /* --- LE read supported states (OCF 0x001C) --- */ |
| #define BLE_HCI_RD_SUPP_STATES_RSPLEN (8) |
| |
| /* --- LE receiver test command (OCF 0x001D) --- */ |
| #define BLE_HCI_RX_TEST_LEN (1) |
| |
| /* --- LE transitter test command (OCF 0x001E) --- */ |
| #define BLE_HCI_TX_TEST_LEN (3) |
| |
| /* --- LE remote connection parameter request reply (OCF 0x0020) */ |
| #define BLE_HCI_CONN_PARAM_REPLY_LEN (14) |
| |
| /* --- LE remote connection parameter request negative reply (OCF 0x0021) */ |
| #define BLE_HCI_CONN_PARAM_NEG_REPLY_LEN (3) |
| |
| /* --- LE set data length (OCF 0x0022) */ |
| #define BLE_HCI_SET_DATALEN_LEN (6) |
| #define BLE_HCI_SET_DATALEN_ACK_PARAM_LEN (2) /* No status byte. */ |
| #define BLE_HCI_SET_DATALEN_TX_OCTETS_MIN (0x001b) |
| #define BLE_HCI_SET_DATALEN_TX_OCTETS_MAX (0x00fb) |
| #define BLE_HCI_SET_DATALEN_TX_TIME_MIN (0x0148) |
| #define BLE_HCI_SET_DATALEN_TX_TIME_MAX (0x4290) |
| |
| /* --- LE read suggested default data length (OCF 0x0023) */ |
| #define BLE_HCI_RD_SUGG_DATALEN_RSPLEN (4) |
| |
| /* --- LE write suggested default data length (OCF 0x0024) */ |
| #define BLE_HCI_WR_SUGG_DATALEN_LEN (4) |
| |
| /* --- LE generate DHKEY command (OCF 0x0026) */ |
| #define BLE_HCI_GEN_DHKEY_LEN (64) |
| |
| /* --- LE add device to resolving list (OCF 0x0027) */ |
| #define BLE_HCI_ADD_TO_RESOLV_LIST_LEN (39) |
| |
| /* --- LE add device to resolving list (OCF 0x0028) */ |
| #define BLE_HCI_RMV_FROM_RESOLV_LIST_LEN (7) |
| |
| /* --- LE read peer resolvable address (OCF 0x002B) */ |
| #define BLE_HCI_RD_PEER_RESOLV_ADDR_LEN (7) |
| |
| /* --- LE read peer resolvable address (OCF 0x002C) */ |
| #define BLE_HCI_RD_LOC_RESOLV_ADDR_LEN (7) |
| |
| /* --- LE set address resolution enable (OCF 0x002D) */ |
| #define BLE_HCI_SET_ADDR_RESOL_ENA_LEN (1) |
| |
| /* --- LE set resolvable private address timeout (OCF 0x002E) */ |
| #define BLE_HCI_SET_RESOLV_PRIV_ADDR_TO_LEN (2) |
| |
| /* --- LE read maximum data length (OCF 0x002F) */ |
| #define BLE_HCI_RD_MAX_DATALEN_RSPLEN (8) |
| |
| /* --- LE read maximum default PHY (OCF 0x0030) */ |
| #define BLE_HCI_LE_RD_PHY_LEN (2) |
| #define BLE_HCI_LE_RD_PHY_RSPLEN (4) |
| #define BLE_HCI_LE_PHY_1M (1) |
| #define BLE_HCI_LE_PHY_2M (2) |
| #define BLE_HCI_LE_PHY_CODED (3) |
| |
| /* --- LE set default PHY (OCF 0x0031) */ |
| #define BLE_HCI_LE_SET_DEFAULT_PHY_LEN (3) |
| #define BLE_HCI_LE_PHY_NO_TX_PREF_MASK (0x01) |
| #define BLE_HCI_LE_PHY_NO_RX_PREF_MASK (0x02) |
| #define BLE_HCI_LE_PHY_1M_PREF_MASK (0x01) |
| #define BLE_HCI_LE_PHY_2M_PREF_MASK (0x02) |
| #define BLE_HCI_LE_PHY_CODED_PREF_MASK (0x04) |
| |
| #define BLE_HCI_LE_PHY_PREF_MASK_ALL \ |
| (BLE_HCI_LE_PHY_1M_PREF_MASK | BLE_HCI_LE_PHY_2M_PREF_MASK | \ |
| BLE_HCI_LE_PHY_CODED_PREF_MASK) |
| |
| /* --- LE set PHY (OCF 0x0032) */ |
| #define BLE_HCI_LE_SET_PHY_LEN (7) |
| #define BLE_HCI_LE_PHY_CODED_ANY (0x0000) |
| #define BLE_HCI_LE_PHY_CODED_S2_PREF (0x0001) |
| #define BLE_HCI_LE_PHY_CODED_S8_PREF (0x0002) |
| |
| /* --- LE enhanced receiver test (OCF 0x0033) */ |
| #define BLE_HCI_LE_ENH_RX_TEST_LEN (3) |
| #define BLE_HCI_LE_PHY_1M (1) |
| #define BLE_HCI_LE_PHY_2M (2) |
| #define BLE_HCI_LE_PHY_CODED (3) |
| |
| /* --- LE enhanced transmitter test (OCF 0x0034) */ |
| #define BLE_HCI_LE_ENH_TX_TEST_LEN (4) |
| #define BLE_HCI_LE_PHY_CODED_S8 (3) |
| #define BLE_HCI_LE_PHY_CODED_S2 (4) |
| |
| /* --- LE set advertising set random address (OCF 0x0035) */ |
| #define BLE_HCI_LE_SET_ADV_SET_RND_ADDR_LEN (7) |
| |
| /* --- LE set extended advertising parameters (OCF 0x0036) */ |
| #define BLE_HCI_LE_SET_EXT_ADV_PARAM_LEN (25) |
| #define BLE_HCI_LE_SET_EXT_ADV_PROP_CONNECTABLE (0x0001) |
| #define BLE_HCI_LE_SET_EXT_ADV_PROP_SCANNABLE (0x0002) |
| #define BLE_HCI_LE_SET_EXT_ADV_PROP_DIRECTED (0x0004) |
| #define BLE_HCI_LE_SET_EXT_ADV_PROP_HD_DIRECTED (0x0008) |
| #define BLE_HCI_LE_SET_EXT_ADV_PROP_LEGACY (0x0010) |
| #define BLE_HCI_LE_SET_EXT_ADV_PROP_ANON_ADV (0x0020) |
| #define BLE_HCI_LE_SET_EXT_ADV_PROP_INC_TX_PWR (0x0040) |
| #define BLE_HCI_LE_SET_EXT_ADV_PROP_MASK (0x7F) |
| |
| #define BLE_HCI_LE_SET_EXT_ADV_PROP_LEGACY_IND (0x0013) |
| #define BLE_HCI_LE_SET_EXT_ADV_PROP_LEGACY_LD_DIR (0x0015) |
| #define BLE_HCI_LE_SET_EXT_ADV_PROP_LEGACY_HD_DIR (0x001d) |
| #define BLE_HCI_LE_SET_EXT_ADV_PROP_LEGACY_SCAN (0x0012) |
| #define BLE_HCI_LE_SET_EXT_ADV_PROP_LEGACY_NONCONN (0x0010) |
| |
| /* --- LE set extended advertising data (OCF 0x0037) */ |
| #define BLE_HCI_MAX_EXT_ADV_DATA_LEN (251) |
| #define BLE_HCI_SET_EXT_ADV_DATA_HDR_LEN (4) |
| |
| #define BLE_HCI_LE_SET_EXT_ADV_DATA_LEN BLE_HCI_VARIABLE_LEN |
| #define BLE_HCI_LE_SET_EXT_ADV_DATA_OPER_INT (0) |
| #define BLE_HCI_LE_SET_EXT_ADV_DATA_OPER_FIRST (1) |
| #define BLE_HCI_LE_SET_EXT_ADV_DATA_OPER_LAST (2) |
| #define BLE_HCI_LE_SET_EXT_ADV_DATA_OPER_COMPLETE (3) |
| #define BLE_HCI_LE_SET_EXT_ADV_DATA_OPER_UNCHANGED (4) |
| |
| /* --- LE set extended scan response data (OCF 0x0038) */ |
| #define BLE_HCI_MAX_EXT_SCAN_RSP_DATA_LEN (251) |
| #define BLE_HCI_SET_EXT_SCAN_RSP_DATA_HDR_LEN (4) |
| |
| #define BLE_HCI_LE_SET_EXT_SCAN_RSP_DATA_LEN BLE_HCI_VARIABLE_LEN |
| #define BLE_HCI_LE_SET_EXT_SCAN_RSP_DATA_OPER_INT (0) |
| #define BLE_HCI_LE_SET_EXT_SCAN_RSP_DATA_OPER_FIRST (1) |
| #define BLE_HCI_LE_SET_EXT_SCAN_RSP_DATA_OPER_LAST (2) |
| #define BLE_HCI_LE_SET_EXT_SCAN_RSP_DATA_OPER_COMPLETE (3) |
| |
| /* --- LE set extended advertising enable (OCF 0x0039) */ |
| #define BLE_HCI_LE_SET_EXT_ADV_ENABLE_LEN BLE_HCI_VARIABLE_LEN |
| |
| /* --- LE remove advertising set (OCF 0x003C) */ |
| #define BLE_HCI_LE_REMOVE_ADV_SET_LEN (1) |
| |
| /* --- LE read maximum advertising data length (OCF 0x003A) */ |
| #define BLE_HCI_RD_MAX_ADV_DATA_LEN (2) |
| |
| /* --- LE read number of supported advertising sets (OCF 0x003B) */ |
| #define BLE_HCI_RD_NR_SUP_ADV_SETS (1) |
| |
| /* --- LE set periodic advertising parameters (OCF 0x003E) */ |
| #define BLE_HCI_LE_SET_PER_ADV_PARAMS_LEN (7) |
| |
| /* --- LE set periodic advertising data (OCF 0x003F) */ |
| #define BLE_HCI_LE_SET_PER_ADV_DATA_LEN BLE_HCI_VARIABLE_LEN |
| |
| /* --- LE periodic advertising enable (OCF 0x0040) */ |
| #define BLE_HCI_LE_SET_PER_ADV_ENABLE_LEN (2) |
| |
| /* --- LE set extended scan parameters (OCF 0x0041) */ |
| #define BLE_HCI_LE_SET_EXT_SCAN_PARAM_LEN BLE_HCI_VARIABLE_LEN |
| #define BLE_HCI_LE_EXT_SCAN_BASE_LEN (3) |
| #define BLE_HCI_LE_EXT_SCAN_SINGLE_PARAM_LEN (5) |
| |
| /* --- LE set extended scan enable (OCF 0x0042) */ |
| #define BLE_HCI_LE_SET_EXT_SCAN_ENABLE_LEN (6) |
| |
| /* --- LE extended create connection (OCF 0x0043) */ |
| #define BLE_HCI_LE_EXT_CREATE_CONN_LEN BLE_HCI_VARIABLE_LEN |
| #define BLE_HCI_LE_EXT_CREATE_CONN_BASE_LEN (10) |
| |
| /* --- LE periodic advertising create sync (OCF 0x0044) */ |
| #define BLE_HCI_LE_PER_ADV_CREATE_SYNC_LEN (14) |
| |
| /* --- LE periodic advertising terminate (OCF 0x0046) */ |
| #define BLE_HCI_LE_PER_ADV_TERM_SYNC_LEN (2) |
| |
| /* --- LE add device to periodic advertising list (OCF 0x0047) */ |
| #define BLE_HCI_LE_ADD_DEV_TO_PER_ADV_LIST_LEN (8) |
| |
| /* --- LE remove device from periodic advertising list (OCF 0x0048) */ |
| #define BLE_HCI_LE_REM_DEV_FROM_PER_ADV_LIST_LEN (8) |
| |
| /* --- LE write RF path (OCF 0x004D) */ |
| #define BLE_HCI_LE_WR_RF_PATH_COMPENSATION_LEN (4) |
| |
| /* --- LE set privacy mode (OCF 0x004E) */ |
| #define BLE_HCI_LE_SET_PRIVACY_MODE_LEN (8) |
| #define BLE_HCI_PRIVACY_NETWORK (0) |
| #define BLE_HCI_PRIVACY_DEVICE (1) |
| |
| /* Event Codes */ |
| #define BLE_HCI_EVCODE_INQUIRY_CMP (0x01) |
| #define BLE_HCI_EVCODE_INQUIRY_RESULT (0x02) |
| #define BLE_HCI_EVCODE_CONN_DONE (0x03) |
| #define BLE_HCI_EVCODE_CONN_REQUEST (0x04) |
| #define BLE_HCI_EVCODE_DISCONN_CMP (0x05) |
| #define BLE_HCI_EVCODE_AUTH_CMP (0x06) |
| #define BLE_HCI_EVCODE_REM_NAME_REQ_CMP (0x07) |
| #define BLE_HCI_EVCODE_ENCRYPT_CHG (0x08) |
| #define BLE_HCI_EVCODE_CHG_LINK_KEY_CMP (0x09) |
| #define BLE_HCI_EVCODE_MASTER_LINK_KEY_CMP (0x0A) |
| #define BLE_HCI_EVCODE_RD_REM_SUPP_FEAT_CMP (0x0B) |
| #define BLE_HCI_EVCODE_RD_REM_VER_INFO_CMP (0x0C) |
| #define BLE_HCI_EVCODE_QOS_SETUP_CMP (0x0D) |
| #define BLE_HCI_EVCODE_COMMAND_COMPLETE (0x0E) |
| #define BLE_HCI_EVCODE_COMMAND_STATUS (0x0F) |
| #define BLE_HCI_EVCODE_HW_ERROR (0x10) |
| #define BLE_HCI_EVCODE_NUM_COMP_PKTS (0x13) |
| #define BLE_HCI_EVCODE_MODE_CHANGE (0x14) |
| #define BLE_HCI_EVCODE_RETURN_LINK_KEYS (0x15) |
| #define BLE_HCI_EVCODE_PIN_CODE_REQ (0x16) |
| #define BLE_HCI_EVCODE_LINK_KEY_REQ (0x17) |
| #define BLE_HCI_EVCODE_LINK_KEY_NOTIFY (0x18) |
| #define BLE_HCI_EVCODE_LOOPBACK_CMD (0x19) |
| #define BLE_HCI_EVCODE_DATA_BUF_OVERFLOW (0x1A) |
| #define BLE_HCI_EVCODE_MAX_SLOTS_CHG (0x1B) |
| #define BLE_HCI_EVCODE_READ_CLK_OFF_COMP (0x1C) |
| #define BLE_HCI_EVCODE_CONN_PKT_TYPE_CHG (0x1D) |
| #define BLE_HCI_EVCODE_QOS_VIOLATION (0x1E) |
| /* NOTE: 0x1F not defined */ |
| #define BLE_HCI_EVCODE_PSR_MODE_CHG (0x20) |
| #define BLE_HCI_EVCODE_FLOW_SPEC_COMP (0x21) |
| #define BLE_HCI_EVCODE_INQ_RESULT_RSSI (0x22) |
| #define BLE_HCI_EVCODE_READ_REM_EXT_FEAT (0x23) |
| /* NOTE: 0x24 - 0x2B not defined */ |
| #define BLE_HCI_EVCODE_SYNCH_CONN_COMP (0x2C) |
| #define BLE_HCI_EVCODE_SYNCH_CONN_CHG (0x2D) |
| #define BLE_HCI_EVCODE_SNIFF_SUBRATING (0x2E) |
| #define BLE_HCI_EVCODE_EXT_INQ_RESULT (0x2F) |
| #define BLE_HCI_EVCODE_ENC_KEY_REFRESH (0x30) |
| #define BLE_HCI_EVOCDE_IO_CAP_REQ (0x31) |
| #define BLE_HCI_EVCODE_IO_CAP_RSP (0x32) |
| #define BLE_HCI_EVCODE_USER_CONFIRM_REQ (0x33) |
| #define BLE_HCI_EVCODE_PASSKEY_REQ (0x34) |
| #define BLE_HCI_EVCODE_REM_OOB_DATA_REQ (0x35) |
| #define BLE_HCI_EVCODE_SIMPLE_PAIR_COMP (0x36) |
| /* NOTE: 0x37 not defined */ |
| #define BLE_HCI_EVCODE_LNK_SPVN_TMO_CHG (0x38) |
| #define BLE_HCI_EVCODE_ENH_FLUSH_COMP (0x39) |
| #define BLE_HCI_EVCODE_USER_PASSKEY_NOTIFY (0x3B) |
| #define BLE_HCI_EVCODE_KEYPRESS_NOTIFY (0x3C) |
| #define BLE_HCI_EVCODE_REM_HOST_SUPP_FEAT (0x3D) |
| #define BLE_HCI_EVCODE_LE_META (0x3E) |
| /* NOTE: 0x3F not defined */ |
| #define BLE_HCI_EVCODE_PHYS_LINK_COMP (0x40) |
| #define BLE_HCI_EVCODE_CHAN_SELECTED (0x41) |
| #define BLE_HCI_EVCODE_DISCONN_PHYS_LINK (0x42) |
| #define BLE_HCI_EVCODE_PHYS_LINK_LOSS_EARLY (0x43) |
| #define BLE_HCI_EVCODE_PHYS_LINK_RECOVERY (0x44) |
| #define BLE_HCI_EVCODE_LOGICAL_LINK_COMP (0x45) |
| #define BLE_HCI_EVCODE_DISCONN_LOGICAL_LINK (0x46) |
| #define BLE_HCI_EVCODE_FLOW_SPEC_MODE_COMP (0x47) |
| #define BLE_HCI_EVCODE_NUM_COMP_DATA_BLKS (0x48) |
| #define BLE_HCI_EVCODE_AMP_START_TEST (0x49) |
| #define BLE_HCI_EVOCDE_AMP_TEST_END (0x4A) |
| #define BLE_HCI_EVOCDE_AMP_RCVR_REPORT (0x4B) |
| #define BLE_HCI_EVCODE_SHORT_RANGE_MODE_CHG (0x4C) |
| #define BLE_HCI_EVCODE_AMP_STATUS_CHG (0x4D) |
| #define BLE_HCI_EVCODE_TRIG_CLK_CAPTURE (0x4E) |
| #define BLE_HCI_EVCODE_SYNCH_TRAIN_COMP (0x4F) |
| #define BLE_HCI_EVCODE_SYNCH_TRAIN_RCVD (0x50) |
| #define BLE_HCI_EVCODE_SLAVE_BCAST_RX (0x51) |
| #define BLE_HCI_EVCODE_SLAVE_BCAST_TMO (0x52) |
| #define BLE_HCI_EVCODE_TRUNC_PAGE_COMP (0x53) |
| #define BLE_HCI_EVCODE_SLAVE_PAGE_RSP_TMO (0x54) |
| #define BLE_HCI_EVCODE_SLAVE_BCAST_CHAN_MAP (0x55) |
| #define BLE_HCI_EVCODE_INQ_RSP_NOTIFY (0x56) |
| #define BLE_HCI_EVCODE_AUTH_PYLD_TMO (0x57) |
| #define BLE_HCI_EVCODE_VENDOR_DEBUG (0xFF) |
| |
| /* LE sub-event codes */ |
| #define BLE_HCI_LE_SUBEV_CONN_COMPLETE (0x01) |
| #define BLE_HCI_LE_SUBEV_ADV_RPT (0x02) |
| #define BLE_HCI_LE_SUBEV_CONN_UPD_COMPLETE (0x03) |
| #define BLE_HCI_LE_SUBEV_RD_REM_USED_FEAT (0x04) |
| #define BLE_HCI_LE_SUBEV_LT_KEY_REQ (0x05) |
| #define BLE_HCI_LE_SUBEV_REM_CONN_PARM_REQ (0x06) |
| #define BLE_HCI_LE_SUBEV_DATA_LEN_CHG (0x07) |
| #define BLE_HCI_LE_SUBEV_RD_LOC_P256_PUBKEY (0x08) |
| #define BLE_HCI_LE_SUBEV_GEN_DHKEY_COMPLETE (0x09) |
| #define BLE_HCI_LE_SUBEV_ENH_CONN_COMPLETE (0x0A) |
| #define BLE_HCI_LE_SUBEV_DIRECT_ADV_RPT (0x0B) |
| #define BLE_HCI_LE_SUBEV_PHY_UPDATE_COMPLETE (0x0C) |
| #define BLE_HCI_LE_SUBEV_EXT_ADV_RPT (0x0D) |
| #define BLE_HCI_LE_SUBEV_PER_ADV_SYNC_ESTAB (0x0E) |
| #define BLE_HCI_LE_SUBEV_PER_ADV_RPT (0x0F) |
| #define BLE_HCI_LE_SUBEV_PER_ADV_SYNC_LOST (0x10) |
| #define BLE_HCI_LE_SUBEV_SCAN_TIMEOUT (0x11) |
| #define BLE_HCI_LE_SUBEV_ADV_SET_TERMINATED (0x12) |
| #define BLE_HCI_LE_SUBEV_SCAN_REQ_RCVD (0x13) |
| #define BLE_HCI_LE_SUBEV_CHAN_SEL_ALG (0x14) |
| |
| /* Generic event header */ |
| #define BLE_HCI_EVENT_HDR_LEN (2) |
| |
| /* Event specific definitions */ |
| /* Event disconnect complete */ |
| #define BLE_HCI_EVENT_DISCONN_COMPLETE_LEN (4) |
| |
| /* Event encryption change (code=0x08) */ |
| #define BLE_HCI_EVENT_ENCRYPT_CHG_LEN (4) |
| |
| /* Event hardware error (code=0x10) */ |
| #define BLE_HCI_EVENT_HW_ERROR_LEN (1) |
| |
| /* Event key refresh complete (code=0x30) */ |
| #define BLE_HCI_EVENT_ENC_KEY_REFRESH_LEN (3) |
| |
| /* Event command complete */ |
| #define BLE_HCI_EVENT_CMD_COMPLETE_HDR_LEN (5) |
| #define BLE_HCI_EVENT_CMD_COMPLETE_MIN_LEN (6) |
| |
| /* Event command status */ |
| #define BLE_HCI_EVENT_CMD_STATUS_LEN (6) |
| |
| /* Number of completed packets */ |
| #define BLE_HCI_EVENT_NUM_COMP_PKTS_HDR_LEN (1) |
| #define BLE_HCI_EVENT_NUM_COMP_PKTS_ENT_LEN (4) |
| |
| /* Read remote version informaton */ |
| #define BLE_HCI_EVENT_RD_RM_VER_LEN (8) |
| |
| /* Data buffer overflow event */ |
| #define BLE_HCI_EVENT_DATABUF_OVERFLOW_LEN (1) |
| #define BLE_HCI_EVENT_ACL_BUF_OVERFLOW (0x01) |
| |
| /* Advertising report */ |
| #define BLE_HCI_ADV_RPT_EVTYPE_ADV_IND (0) |
| #define BLE_HCI_ADV_RPT_EVTYPE_DIR_IND (1) |
| #define BLE_HCI_ADV_RPT_EVTYPE_SCAN_IND (2) |
| #define BLE_HCI_ADV_RPT_EVTYPE_NONCONN_IND (3) |
| #define BLE_HCI_ADV_RPT_EVTYPE_SCAN_RSP (4) |
| |
| /* Bluetooth 5, Vol 2, Part E, 7.7.65.13 */ |
| #define BLE_HCI_LEGACY_ADV_EVTYPE_ADV_IND (0x13) |
| #define BLE_HCI_LEGACY_ADV_EVTYPE_ADV_DIRECT_IND (0x15) |
| #define BLE_HCI_LEGACY_ADV_EVTYPE_ADV_SCAN_IND (0x12) |
| #define BLE_HCI_LEGACY_ADV_EVTYPE_ADV_NONCON_IND (0x10) |
| #define BLE_HCI_LEGACY_ADV_EVTYPE_SCAN_RSP_ADV_IND (0x1b) |
| #define BLE_HCI_LEGACY_ADV_EVTYPE_SCAN_RSP_ADV_SCAN_IND (0x1a) |
| |
| /* LE sub-event specific definitions */ |
| #define BLE_HCI_LE_MIN_LEN (1) /* Not including event hdr. */ |
| |
| /* LE connection complete event (sub event 0x01) */ |
| #define BLE_HCI_LE_CONN_COMPLETE_LEN (19) |
| #define BLE_HCI_LE_CONN_COMPLETE_ROLE_MASTER (0x00) |
| #define BLE_HCI_LE_CONN_COMPLETE_ROLE_SLAVE (0x01) |
| |
| /* Maximum valid connection handle value */ |
| #define BLE_HCI_LE_CONN_HANDLE_MAX (0x0eff) |
| |
| /* LE advertising report event. (sub event 0x02) */ |
| #define BLE_HCI_LE_ADV_RPT_MIN_LEN (12) |
| #define BLE_HCI_LE_ADV_DIRECT_RPT_LEN (18) |
| #define BLE_HCI_LE_ADV_RPT_NUM_RPTS_MIN (1) |
| #define BLE_HCI_LE_ADV_RPT_NUM_RPTS_MAX (0x19) |
| |
| /* Length of each record in an LE direct advertising report event. */ |
| #define BLE_HCI_LE_ADV_DIRECT_RPT_SUB_LEN (16) |
| |
| /* LE connection update complete event (sub event 0x03) */ |
| #define BLE_HCI_LE_CONN_UPD_LEN (10) |
| |
| /* LE long term key request event (sub event 0x05) */ |
| #define BLE_HCI_LE_LT_KEY_REQ_LEN (13) |
| |
| /* LE connection update complete event (sub event 0x03) */ |
| #define BLE_HCI_LE_RD_REM_USED_FEAT_LEN (12) |
| |
| /* LE remote connection parameter request event (sub event 0x06) */ |
| #define BLE_HCI_LE_REM_CONN_PARM_REQ_LEN (11) |
| |
| /* LE data length change event (sub event 0x07) */ |
| #define BLE_HCI_LE_DATA_LEN_CHG_LEN (11) |
| |
| /* LE PHY update complete event (sub event 0x0C) */ |
| #define BLE_HCI_LE_PHY_UPD_LEN (6) |
| |
| /* LE Scan Timeout Event (sub event 0x11) */ |
| #define BLE_HCI_LE_SUBEV_SCAN_TIMEOUT_LEN (1) |
| |
| /* LE Advertising Set Terminated Event (sub event 0x12) */ |
| #define BLE_HCI_LE_SUBEV_ADV_SET_TERMINATED_LEN (6) |
| |
| /* LE Scan Request Received event (sub event 0x13) */ |
| #define BLE_HCI_LE_SUBEV_SCAN_REQ_RCVD_LEN (9) |
| |
| /* LE Channel Selection Algorithm event (sub event 0x14) */ |
| #define BLE_HCI_LE_SUBEV_CHAN_SEL_ALG_LEN (4) |
| |
| /* Bluetooth Assigned numbers for version information.*/ |
| #define BLE_HCI_VER_BCS_1_0b (0) |
| #define BLE_HCI_VER_BCS_1_1 (1) |
| #define BLE_HCI_VER_BCS_1_2 (2) |
| #define BLE_HCI_VER_BCS_2_0_EDR (3) |
| #define BLE_HCI_VER_BCS_2_1_EDR (4) |
| #define BLE_HCI_VER_BCS_3_0_HCS (5) |
| #define BLE_HCI_VER_BCS_4_0 (6) |
| #define BLE_HCI_VER_BCS_4_1 (7) |
| #define BLE_HCI_VER_BCS_4_2 (8) |
| #define BLE_HCI_VER_BCS_5_0 (9) |
| |
| #define BLE_LMP_VER_BCS_1_0b (0) |
| #define BLE_LMP_VER_BCS_1_1 (1) |
| #define BLE_LMP_VER_BCS_1_2 (2) |
| #define BLE_LMP_VER_BCS_2_0_EDR (3) |
| #define BLE_LMP_VER_BCS_2_1_EDR (4) |
| #define BLE_LMP_VER_BCS_3_0_HCS (5) |
| #define BLE_LMP_VER_BCS_4_0 (6) |
| #define BLE_LMP_VER_BCS_4_1 (7) |
| #define BLE_LMP_VER_BCS_4_2 (8) |
| #define BLE_LMP_VER_BCS_5_0 (9) |
| |
| /* Sub-event 0x0A: enhanced connection complete */ |
| #define BLE_HCI_LE_ENH_CONN_COMPLETE_LEN (31) |
| |
| /*--- Shared data structures ---*/ |
| |
| /* Host buffer size (OGF=0x03, OCF=0x0033) */ |
| struct hci_host_buf_size |
| { |
| uint16_t acl_pkt_len; |
| uint8_t sync_pkt_len; |
| uint16_t num_acl_pkts; |
| uint16_t num_sync_pkts; |
| }; |
| |
| /* Host number of completed packets (OGF=0x03, OCF=0x0035) */ |
| struct hci_host_num_comp_pkts_entry |
| { |
| uint16_t conn_handle; |
| uint16_t num_pkts; |
| }; |
| |
| /* Read local version information (OGF=0x0004, OCF=0x0001) */ |
| struct hci_loc_ver_info |
| { |
| uint8_t status; |
| uint8_t hci_version; |
| uint16_t hci_revision; |
| uint8_t lmp_pal_version; |
| uint16_t mfrg_name; |
| uint8_t lmp_pal_subversion; |
| }; |
| |
| /* set random address command (ocf = 0x0005) */ |
| struct hci_rand_addr |
| { |
| uint8_t addr[6]; |
| }; |
| |
| /* set advertising parameters command (ocf = 0x0006) */ |
| struct hci_adv_params |
| { |
| uint8_t adv_type; |
| uint8_t adv_channel_map; |
| uint8_t own_addr_type; |
| uint8_t peer_addr_type; |
| uint8_t adv_filter_policy; |
| uint16_t adv_itvl_min; |
| uint16_t adv_itvl_max; |
| uint8_t peer_addr[BLE_DEV_ADDR_LEN]; |
| }; |
| |
| /* LE create connection command (ocf=0x000d). */ |
| struct hci_create_conn |
| { |
| uint16_t scan_itvl; |
| uint16_t scan_window; |
| uint8_t filter_policy; |
| uint8_t peer_addr_type; |
| uint8_t peer_addr[BLE_DEV_ADDR_LEN]; |
| uint8_t own_addr_type; |
| uint16_t conn_itvl_min; |
| uint16_t conn_itvl_max; |
| uint16_t conn_latency; |
| uint16_t supervision_timeout; |
| uint16_t min_ce_len; |
| uint16_t max_ce_len; |
| }; |
| |
| /* LE Read Local P-256 Public Key Complete Event */ |
| struct hci_le_subev_rd_loc_p256_pubkey { |
| uint8_t status; |
| uint8_t pubkey[64]; |
| } __attribute__((packed)); |
| |
| /* LE Generate DHKey Complete Event */ |
| struct hci_le_subev_gen_dhkey_complete { |
| uint8_t status; |
| uint8_t dhkey[32]; |
| } __attribute__((packed)); |
| |
| /* LE Directed Advertising Report Event */ |
| struct hci_le_subev_direct_adv_rpt_param { |
| uint8_t evt_type; |
| uint8_t addr_type; |
| uint8_t addr[6]; |
| uint8_t dir_addr_type; |
| uint8_t dir_addr[6]; |
| int8_t rssi; |
| } __attribute__((packed)); |
| |
| struct hci_le_subev_direct_adv_rpt { |
| uint8_t num_reports; |
| struct hci_le_subev_direct_adv_rpt_param params[0]; |
| } __attribute__((packed)); |
| |
| #if MYNEWT_VAL(BLE_EXT_ADV) |
| /* LE create connection command (ocf=0x0043). */ |
| struct hci_ext_conn_params |
| { |
| uint16_t scan_itvl; |
| uint16_t scan_window; |
| uint16_t conn_itvl_min; |
| uint16_t conn_itvl_max; |
| uint16_t conn_latency; |
| uint16_t supervision_timeout; |
| uint16_t min_ce_len; |
| uint16_t max_ce_len; |
| }; |
| |
| struct hci_ext_create_conn |
| { |
| uint8_t filter_policy; |
| uint8_t own_addr_type; |
| uint8_t peer_addr_type; |
| uint8_t peer_addr[BLE_DEV_ADDR_LEN]; |
| uint8_t init_phy_mask; |
| struct hci_ext_conn_params params[3]; |
| }; |
| |
| struct hci_ext_adv_report_param { |
| uint16_t evt_type; |
| uint8_t addr_type; |
| uint8_t addr[6]; |
| uint8_t prim_phy; |
| uint8_t sec_phy; |
| uint8_t sid; |
| int8_t tx_power; |
| int8_t rssi; |
| uint16_t per_adv_itvl; |
| uint8_t dir_addr_type; |
| uint8_t dir_addr[6]; |
| uint8_t adv_data_len; |
| uint8_t adv_data[0]; |
| } __attribute__((packed)); |
| |
| struct hci_ext_adv_report { |
| /* We support one report per event for now */ |
| uint8_t subevt; |
| uint8_t num_reports; |
| struct hci_ext_adv_report_param params[0]; |
| } __attribute__((packed)); |
| |
| /* Ext Adv Set enable parameters, not in HCI order */ |
| struct hci_ext_adv_set |
| { |
| uint8_t handle; |
| uint8_t events; |
| uint16_t duration; |
| }; |
| |
| /* Ext Advertising Parameters */ |
| struct hci_ext_adv_params |
| { |
| uint16_t properties; |
| uint32_t min_interval; |
| uint32_t max_interval; |
| uint8_t chan_map; |
| uint8_t own_addr_type; |
| uint8_t peer_addr_type; |
| uint8_t peer_addr[6]; |
| uint8_t filter_policy; |
| int8_t tx_power; |
| uint8_t primary_phy; |
| uint8_t max_skip; |
| uint8_t secondary_phy; |
| uint8_t sid; |
| uint8_t scan_req_notif; |
| }; |
| |
| /* LE Extended Advertising Report Event */ |
| struct hci_le_subev_ext_adv_rpt { |
| uint8_t num_reports; |
| struct hci_ext_adv_report_param params[0]; |
| } __attribute__((packed)); |
| |
| /* LE Periodic Advertising Sync Established Event */ |
| struct hci_le_subev_per_adv_sync_estab { |
| uint8_t status; |
| uint16_t sync_handle; |
| uint8_t sid; |
| uint8_t adv_addr_type; |
| uint8_t adv_addr[6]; |
| uint8_t adv_phy; |
| uint16_t per_adv_ival; |
| uint8_t adv_clk_accuracy; |
| } __attribute__((packed)); |
| |
| /* LE Periodic Advertising Report Event */ |
| struct hci_le_subev_per_adv_rpt { |
| uint16_t sync_handle; |
| uint8_t tx_power; |
| int8_t rssi; |
| uint8_t _unused; |
| uint8_t data_status; |
| uint8_t data_length; |
| uint8_t data[0]; |
| } __attribute__((packed)); |
| |
| /* LE Periodic Advertising Sync Lost Event */ |
| struct hci_le_subev_per_adv_sync_lost { |
| uint16_t sync_handle; |
| } __attribute__((packed)); |
| |
| /* LE Advertising Set Terminated Event */ |
| struct hci_le_subev_adv_set_terminated { |
| uint8_t status; |
| uint8_t adv_handle; |
| uint16_t conn_handle; |
| uint8_t num_compl_ext_adv_ev; |
| } __attribute__((packed)); |
| |
| /* LE Scan Request Received Event */ |
| struct hci_le_subev_scan_req_rcvd { |
| uint8_t adv_handle; |
| uint8_t scan_addr_type; |
| uint8_t scan_addr[6]; |
| } __attribute__((packed)); |
| |
| #endif |
| |
| /* LE Channel Selection Algorithm Event */ |
| struct hci_le_subev_chan_sel_alg { |
| uint16_t conn_handle; |
| uint8_t chan_sel_alg; |
| } __attribute__((packed)); |
| |
| /* LE connection update command (ocf=0x0013). */ |
| struct hci_conn_update |
| { |
| uint16_t handle; |
| uint16_t conn_itvl_min; |
| uint16_t conn_itvl_max; |
| uint16_t conn_latency; |
| uint16_t supervision_timeout; |
| uint16_t min_ce_len; |
| uint16_t max_ce_len; |
| }; |
| |
| /* LE start encryption command (ocf=0x0019) (note: fields out of order). */ |
| struct hci_start_encrypt |
| { |
| uint16_t connection_handle; |
| uint16_t encrypted_diversifier; |
| uint64_t random_number; |
| uint8_t long_term_key[16]; |
| }; |
| |
| /* LE long term key request reply command (ocf=0x001a). */ |
| struct hci_lt_key_req_reply |
| { |
| uint16_t conn_handle; |
| uint8_t long_term_key[16]; |
| }; |
| |
| /* LE Remote connection parameter request reply command */ |
| struct hci_conn_param_reply |
| { |
| uint16_t handle; |
| uint16_t conn_itvl_min; |
| uint16_t conn_itvl_max; |
| uint16_t conn_latency; |
| uint16_t supervision_timeout; |
| uint16_t min_ce_len; |
| uint16_t max_ce_len; |
| }; |
| |
| /* LE Remote connection parameter request negative reply command */ |
| struct hci_conn_param_neg_reply |
| { |
| uint16_t handle; |
| uint8_t reason; |
| }; |
| |
| /* Encryption change event (code=0x08) (note: fields out of order) */ |
| struct hci_encrypt_change |
| { |
| uint8_t status; |
| uint8_t encryption_enabled; |
| uint16_t connection_handle; |
| }; |
| |
| /* Encryption key refresh complete event (code=0x30) */ |
| struct hci_encrypt_key_refresh |
| { |
| uint8_t status; |
| uint16_t connection_handle; |
| }; |
| |
| /* Connection complete LE meta subevent */ |
| struct hci_le_conn_complete |
| { |
| uint8_t subevent_code; |
| uint8_t status; |
| uint16_t connection_handle; |
| uint8_t role; |
| uint8_t peer_addr_type; |
| uint8_t peer_addr[BLE_DEV_ADDR_LEN]; |
| uint16_t conn_itvl; |
| uint16_t conn_latency; |
| uint16_t supervision_timeout; |
| uint8_t master_clk_acc; |
| uint8_t local_rpa[BLE_DEV_ADDR_LEN]; |
| uint8_t peer_rpa[BLE_DEV_ADDR_LEN]; |
| }; |
| |
| /* Connection update complete LE meta subevent */ |
| struct hci_le_conn_upd_complete |
| { |
| uint8_t subevent_code; |
| uint8_t status; |
| uint16_t connection_handle; |
| uint16_t conn_itvl; |
| uint16_t conn_latency; |
| uint16_t supervision_timeout; |
| }; |
| |
| /* Remote connection parameter request LE meta subevent */ |
| struct hci_le_conn_param_req |
| { |
| uint8_t subevent_code; |
| uint16_t connection_handle; |
| uint16_t itvl_min; |
| uint16_t itvl_max; |
| uint16_t latency; |
| uint16_t timeout; |
| }; |
| |
| /* Read Remote Supported Features complete LE meta subevent */ |
| struct hci_le_rd_rem_supp_feat_complete |
| { |
| uint8_t subevent_code; |
| uint8_t status; |
| uint16_t connection_handle; |
| uint8_t features[8]; |
| }; |
| |
| /* LE long term key request event (note: fields out of order). */ |
| struct hci_le_lt_key_req |
| { |
| uint64_t random_number; |
| uint16_t connection_handle; |
| uint16_t encrypted_diversifier; |
| uint8_t subevent_code; |
| }; |
| |
| /* Disconnection complete event (note: fields out of order). */ |
| struct hci_disconn_complete |
| { |
| uint16_t connection_handle; |
| uint8_t status; |
| uint8_t reason; |
| }; |
| |
| /* Read RSSI command-complete parameters (note: fields out of order). */ |
| struct hci_read_rssi_ack_params |
| { |
| uint16_t connection_handle; |
| uint8_t status; |
| int8_t rssi; |
| }; |
| |
| /* PHY updated completed LE meta subevent */ |
| struct hci_le_phy_upd_complete |
| { |
| uint8_t subevent_code; |
| uint8_t status; |
| uint16_t connection_handle; |
| uint8_t tx_phy; |
| uint8_t rx_phy; |
| }; |
| |
| /* LE Advertising Set Terminated subevent*/ |
| struct hci_le_adv_set_terminated |
| { |
| uint8_t subevent_code; |
| uint8_t status; |
| uint8_t adv_handle; |
| uint16_t conn_handle; |
| uint8_t completed_events; |
| }; |
| |
| #define BLE_HCI_DATA_HDR_SZ 4 |
| #define BLE_HCI_DATA_HANDLE(handle_pb_bc) (((handle_pb_bc) & 0x0fff) >> 0) |
| #define BLE_HCI_DATA_PB(handle_pb_bc) (((handle_pb_bc) & 0x3000) >> 12) |
| #define BLE_HCI_DATA_BC(handle_pb_bc) (((handle_pb_bc) & 0xc000) >> 14) |
| |
| struct hci_data_hdr |
| { |
| uint16_t hdh_handle_pb_bc; |
| uint16_t hdh_len; |
| }; |
| |
| #define BLE_HCI_PB_FIRST_NON_FLUSH 0 |
| #define BLE_HCI_PB_MIDDLE 1 |
| #define BLE_HCI_PB_FIRST_FLUSH 2 |
| #define BLE_HCI_PB_FULL 3 |
| |
| struct hci_add_dev_to_resolving_list { |
| uint8_t addr_type; |
| uint8_t addr[6]; |
| uint8_t local_irk[16]; |
| uint8_t peer_irk[16]; |
| }; |
| |
| /* External data structures */ |
| extern const uint8_t g_ble_hci_le_cmd_len[BLE_HCI_NUM_LE_CMDS]; |
| |
| #ifdef __cplusplus |
| } |
| #endif |
| |
| #endif /* H_BLE_HCI_COMMON_ */ |
