| /* |
| * Licensed to the Apache Software Foundation (ASF) under one |
| * or more contributor license agreements. See the NOTICE file |
| * distributed with this work for additional information |
| * regarding copyright ownership. The ASF licenses this file |
| * to you under the Apache License, Version 2.0 (the |
| * "License"); you may not use this file except in compliance |
| * with the License. You may obtain a copy of the License at |
| * |
| * http://www.apache.org/licenses/LICENSE-2.0 |
| * |
| * Unless required by applicable law or agreed to in writing, |
| * software distributed under the License is distributed on an |
| * "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY |
| * KIND, either express or implied. See the License for the |
| * specific language governing permissions and limitations |
| * under the License. |
| */ |
| |
| /* Bluetooth: Mesh Generic OnOff, Generic Level, Lighting & Vendor Models |
| * |
| * Copyright (c) 2018 Vikrant More |
| * |
| * SPDX-License-Identifier: Apache-2.0 |
| */ |
| |
| #include "console/console.h" |
| |
| #include "common.h" |
| #include "ble_mesh.h" |
| #include "device_composition.h" |
| |
| #define OOB_AUTH_ENABLE 1 |
| |
| #ifdef OOB_AUTH_ENABLE |
| |
| static int output_number(bt_mesh_output_action_t action, u32_t number) |
| { |
| printk("OOB Number: %lu\n", number); |
| return 0; |
| } |
| |
| static int output_string(const char *str) |
| { |
| printk("OOB String: %s\n", str); |
| return 0; |
| } |
| |
| #endif |
| |
| static void prov_complete(u16_t net_idx, u16_t addr) |
| { |
| printk("Local node provisioned, primary address 0x%04x\n", addr); |
| } |
| |
| static void prov_reset(void) |
| { |
| bt_mesh_prov_enable(BT_MESH_PROV_ADV | BT_MESH_PROV_GATT); |
| } |
| |
| static u8_t dev_uuid[16] = MYNEWT_VAL(BLE_MESH_DEV_UUID); |
| |
| static const struct bt_mesh_prov prov = { |
| .uuid = dev_uuid, |
| |
| #ifdef OOB_AUTH_ENABLE |
| |
| .output_size = 6, |
| .output_actions = BT_MESH_DISPLAY_NUMBER | BT_MESH_DISPLAY_STRING, |
| .output_number = output_number, |
| .output_string = output_string, |
| |
| #endif |
| |
| .complete = prov_complete, |
| .reset = prov_reset, |
| }; |
| |
| void blemesh_on_reset(int reason) |
| { |
| BLE_HS_LOG(ERROR, "Resetting state; reason=%d\n", reason); |
| } |
| |
| void blemesh_on_sync(void) |
| { |
| int err; |
| ble_addr_t addr; |
| |
| console_printf("Bluetooth initialized\n"); |
| |
| /* Use NRPA */ |
| err = ble_hs_id_gen_rnd(1, &addr); |
| assert(err == 0); |
| err = ble_hs_id_set_rnd(addr.val); |
| assert(err == 0); |
| |
| err = bt_mesh_init(addr.type, &prov, &comp); |
| if (err) { |
| console_printf("Initializing mesh failed (err %d)\n", err); |
| return; |
| } |
| |
| if (IS_ENABLED(CONFIG_SETTINGS)) { |
| settings_load(); |
| } |
| |
| if (bt_mesh_is_provisioned()) { |
| console_printf("Mesh network restored from flash\n"); |
| } |
| |
| bt_mesh_prov_enable(BT_MESH_PROV_GATT | BT_MESH_PROV_ADV); |
| |
| console_printf("Mesh initialized\n"); |
| |
| bt_initialized(); |
| } |