| /* |
| * Licensed to the Apache Software Foundation (ASF) under one |
| * or more contributor license agreements. See the NOTICE file |
| * distributed with this work for additional information |
| * regarding copyright ownership. The ASF licenses this file |
| * to you under the Apache License, Version 2.0 (the |
| * "License"); you may not use this file except in compliance |
| * with the License. You may obtain a copy of the License at |
| * |
| * http://www.apache.org/licenses/LICENSE-2.0 |
| * |
| * Unless required by applicable law or agreed to in writing, |
| * software distributed under the License is distributed on an |
| * "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY |
| * KIND, either express or implied. See the License for the |
| * specific language governing permissions and limitations |
| * under the License. |
| */ |
| |
| #ifndef H_NRF52_HAL_ |
| #define H_NRF52_HAL_ |
| |
| #ifdef __cplusplus |
| extern "C" { |
| #endif |
| |
| /* Helper functions to enable/disable interrupts. */ |
| #define __HAL_DISABLE_INTERRUPTS(x) \ |
| do { \ |
| x = __get_PRIMASK(); \ |
| __disable_irq(); \ |
| } while(0); |
| |
| #define __HAL_ENABLE_INTERRUPTS(x) \ |
| do { \ |
| if (!x) { \ |
| __enable_irq(); \ |
| } \ |
| } while(0); |
| |
| struct nrf52_uart_cfg { |
| int8_t suc_pin_tx; /* pins for IO */ |
| int8_t suc_pin_rx; |
| int8_t suc_pin_rts; |
| int8_t suc_pin_cts; |
| }; |
| const struct nrf52_uart_cfg *bsp_uart_config(void); |
| |
| struct nrf52_hal_i2c_cfg { |
| int scl_pin; |
| int sda_pin; |
| uint32_t i2c_frequency; |
| }; |
| struct hal_flash; |
| extern const struct hal_flash nrf52k_flash_dev; |
| extern const struct hal_flash nrf52k_qspi_dev; |
| |
| /* SPI configuration (used for both master and slave) */ |
| struct nrf52_hal_spi_cfg { |
| uint8_t sck_pin; |
| uint8_t mosi_pin; |
| uint8_t miso_pin; |
| uint8_t ss_pin; |
| }; |
| |
| /* |
| * GPIO pin mapping |
| * |
| * The logical GPIO pin numbers (0 to N) are mapped to ports in the following |
| * manner: |
| * pins 0 - 31: Port 0 |
| * pins 32 - 48: Port 1. |
| * |
| * The nrf52832 has only one port with 32 pins. The nrf52840 has 48 pins and |
| * uses two ports. |
| * |
| * NOTE: in order to save code space, there is no checking done to see if the |
| * user specifies a pin that is not used by the processor. If an invalid pin |
| * number is used unexpected and/or erroneous behavior will result. |
| */ |
| #ifdef NRF52 |
| #define HAL_GPIO_INDEX(pin) (pin) |
| #define HAL_GPIO_PORT(pin) (NRF_P0) |
| #define HAL_GPIO_MASK(pin) (1 << pin) |
| #define HAL_GPIOTE_PIN_MASK GPIOTE_CONFIG_PSEL_Msk |
| #endif |
| |
| #ifdef NRF52840_XXAA |
| #define HAL_GPIO_INDEX(pin) ((pin) & 0x1F) |
| #define HAL_GPIO_PORT(pin) ((pin) > 31 ? NRF_P1 : NRF_P0) |
| #define HAL_GPIO_MASK(pin) (1 << HAL_GPIO_INDEX(pin)) |
| #define HAL_GPIOTE_PIN_MASK (0x3FUL << GPIOTE_CONFIG_PSEL_Pos) |
| #endif |
| |
| #ifdef __cplusplus |
| } |
| #endif |
| |
| #endif /* H_NRF52_HAL_ */ |
| |