/** | |
****************************************************************************** | |
* @file stm32f3xx_hal_conf.h | |
* @author MCD Application Team | |
* @brief HAL configuration file. | |
****************************************************************************** | |
* @attention | |
* | |
* <h2><center>© COPYRIGHT(c) 2016 STMicroelectronics</center></h2> | |
* | |
* Redistribution and use in source and binary forms, with or without modification, | |
* are permitted provided that the following conditions are met: | |
* 1. Redistributions of source code must retain the above copyright notice, | |
* this list of conditions and the following disclaimer. | |
* 2. Redistributions in binary form must reproduce the above copyright notice, | |
* this list of conditions and the following disclaimer in the documentation | |
* and/or other materials provided with the distribution. | |
* 3. Neither the name of STMicroelectronics nor the names of its contributors | |
* may be used to endorse or promote products derived from this software | |
* without specific prior written permission. | |
* | |
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" | |
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE | |
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE | |
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE | |
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL | |
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR | |
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER | |
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, | |
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE | |
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. | |
* | |
****************************************************************************** | |
*/ | |
/* Define to prevent recursive inclusion -------------------------------------*/ | |
#ifndef __STM32F3xx_HAL_CONF_H | |
#define __STM32F3xx_HAL_CONF_H | |
#ifdef __cplusplus | |
extern "C" { | |
#endif | |
/* Exported types ------------------------------------------------------------*/ | |
/* Exported constants --------------------------------------------------------*/ | |
/* ########################## Module Selection ############################## */ | |
/** | |
* @brief This is the list of modules to be used in the HAL driver | |
*/ | |
#define HAL_MODULE_ENABLED | |
/* #define HAL_ADC_MODULE_ENABLED */ | |
/* #define HAL_CAN_MODULE_ENABLED */ | |
/* #define HAL_CEC_MODULE_ENABLED */ | |
/* #define HAL_COMP_MODULE_ENABLED */ | |
#define HAL_CORTEX_MODULE_ENABLED | |
/* #define HAL_CRC_MODULE_ENABLED */ | |
/* #define HAL_DAC_MODULE_ENABLED */ | |
#define HAL_DMA_MODULE_ENABLED | |
#define HAL_FLASH_MODULE_ENABLED | |
#define HAL_SRAM_MODULE_ENABLED | |
#define HAL_NOR_MODULE_ENABLED | |
#define HAL_NAND_MODULE_ENABLED | |
/* #define HAL_PCCARD_MODULE_ENABLED */ | |
#define HAL_GPIO_MODULE_ENABLED | |
/* #define HAL_HRTIM_MODULE_ENABLED */ | |
#define HAL_I2C_MODULE_ENABLED | |
/* #define HAL_I2S_MODULE_ENABLED */ | |
/* #define HAL_IRDA_MODULE_ENABLED */ | |
#define HAL_IWDG_MODULE_ENABLED | |
/* #define HAL_OPAMP_MODULE_ENABLED */ | |
/* #define HAL_PCD_MODULE_ENABLED */ | |
#define HAL_PWR_MODULE_ENABLED | |
#define HAL_RCC_MODULE_ENABLED | |
#define HAL_RTC_MODULE_ENABLED | |
/* #define HAL_SDADC_MODULE_ENABLED */ | |
/* #define HAL_SMARTCARD_MODULE_ENABLED */ | |
/* #define HAL_SMBUS_MODULE_ENABLED */ | |
/* #define HAL_SPI_MODULE_ENABLED */ | |
#define HAL_TIM_MODULE_ENABLED | |
/* #define HAL_TSC_MODULE_ENABLED */ | |
/* #define HAL_UART_MODULE_ENABLED */ | |
#define HAL_USART_MODULE_ENABLED | |
/* #define HAL_WWDG_MODULE_ENABLED */ | |
/* ########################## HSE/HSI Values adaptation ##################### */ | |
/** | |
* @brief Adjust the value of External High Speed oscillator (HSE) used in your application. | |
* This value is used by the RCC HAL module to compute the system frequency | |
* (when HSE is used as system clock source, directly or through the PLL). | |
*/ | |
#if !defined (HSE_VALUE) | |
#define HSE_VALUE (8000000U) /*!< Value of the External oscillator in Hz */ | |
#endif /* HSE_VALUE */ | |
/** | |
* @brief In the following line adjust the External High Speed oscillator (HSE) Startup | |
* Timeout value | |
*/ | |
#if !defined (HSE_STARTUP_TIMEOUT) | |
#define HSE_STARTUP_TIMEOUT (100U) /*!< Time out for HSE start up, in ms */ | |
#endif /* HSE_STARTUP_TIMEOUT */ | |
/** | |
* @brief Internal High Speed oscillator (HSI) value. | |
* This value is used by the RCC HAL module to compute the system frequency | |
* (when HSI is used as system clock source, directly or through the PLL). | |
*/ | |
#if !defined (HSI_VALUE) | |
#define HSI_VALUE (8000000U) /*!< Value of the Internal oscillator in Hz*/ | |
#endif /* HSI_VALUE */ | |
/** | |
* @brief In the following line adjust the Internal High Speed oscillator (HSI) Startup | |
* Timeout value | |
*/ | |
#if !defined (HSI_STARTUP_TIMEOUT) | |
#define HSI_STARTUP_TIMEOUT (5000U) /*!< Time out for HSI start up */ | |
#endif /* HSI_STARTUP_TIMEOUT */ | |
/** | |
* @brief Internal Low Speed oscillator (LSI) value. | |
*/ | |
#if !defined (LSI_VALUE) | |
#define LSI_VALUE (40000U) | |
#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz | |
The real value may vary depending on the variations | |
in voltage and temperature. */ | |
/** | |
* @brief External Low Speed oscillator (LSE) value. | |
*/ | |
#if !defined (LSE_VALUE) | |
#define LSE_VALUE (32768U) /*!< Value of the External Low Speed oscillator in Hz */ | |
#endif /* LSE_VALUE */ | |
/** | |
* @brief Time out for LSE start up value in ms. | |
*/ | |
#if !defined (LSE_STARTUP_TIMEOUT) | |
#define LSE_STARTUP_TIMEOUT (5000U) /*!< Time out for LSE start up, in ms */ | |
#endif /* LSE_STARTUP_TIMEOUT */ | |
/** | |
* @brief External clock source for I2S peripheral | |
* This value is used by the I2S HAL module to compute the I2S clock source | |
* frequency, this source is inserted directly through I2S_CKIN pad. | |
* - External clock generated through external PLL component on EVAL 303 (based on MCO or crystal) | |
* - External clock not generated on EVAL 373 | |
*/ | |
#if !defined (EXTERNAL_CLOCK_VALUE) | |
#define EXTERNAL_CLOCK_VALUE (8000000U) /*!< Value of the External oscillator in Hz*/ | |
#endif /* EXTERNAL_CLOCK_VALUE */ | |
/* Tip: To avoid modifying this file each time you need to use different HSE, | |
=== you can define the HSE value in your toolchain compiler preprocessor. */ | |
/* ########################### System Configuration ######################### */ | |
/** | |
* @brief This is the HAL system configuration section | |
*/ | |
#define VDD_VALUE (3300U) /*!< Value of VDD in mv */ | |
#define TICK_INT_PRIORITY ((uint32_t)(1U<<__NVIC_PRIO_BITS) - 1U) /*!< tick interrupt priority (lowest by default) */ | |
#define USE_RTOS 0U | |
#define PREFETCH_ENABLE 1U | |
#define INSTRUCTION_CACHE_ENABLE 0U | |
#define DATA_CACHE_ENABLE 0U | |
#define USE_SPI_CRC 0U | |
/* ########################## Assert Selection ############################## */ | |
/** | |
* @brief Uncomment the line below to expanse the "assert_param" macro in the | |
* HAL drivers code | |
*/ | |
/*#define USE_FULL_ASSERT 1*/ | |
/* Includes ------------------------------------------------------------------*/ | |
/** | |
* @brief Include module's header file | |
*/ | |
#ifdef HAL_RCC_MODULE_ENABLED | |
#include "stm32f3xx_hal_rcc.h" | |
#endif /* HAL_RCC_MODULE_ENABLED */ | |
#ifdef HAL_GPIO_MODULE_ENABLED | |
#include "stm32f3xx_hal_gpio.h" | |
#endif /* HAL_GPIO_MODULE_ENABLED */ | |
#ifdef HAL_DMA_MODULE_ENABLED | |
#include "stm32f3xx_hal_dma.h" | |
#endif /* HAL_DMA_MODULE_ENABLED */ | |
#ifdef HAL_CORTEX_MODULE_ENABLED | |
#include "stm32f3xx_hal_cortex.h" | |
#endif /* HAL_CORTEX_MODULE_ENABLED */ | |
#ifdef HAL_ADC_MODULE_ENABLED | |
#include "stm32f3xx_hal_adc.h" | |
#endif /* HAL_ADC_MODULE_ENABLED */ | |
#ifdef HAL_CAN_MODULE_ENABLED | |
#include "stm32f3xx_hal_can.h" | |
#endif /* HAL_CAN_MODULE_ENABLED */ | |
#ifdef HAL_CEC_MODULE_ENABLED | |
#include "stm32f3xx_hal_cec.h" | |
#endif /* HAL_CEC_MODULE_ENABLED */ | |
#ifdef HAL_COMP_MODULE_ENABLED | |
#include "stm32f3xx_hal_comp.h" | |
#endif /* HAL_COMP_MODULE_ENABLED */ | |
#ifdef HAL_CRC_MODULE_ENABLED | |
#include "stm32f3xx_hal_crc.h" | |
#endif /* HAL_CRC_MODULE_ENABLED */ | |
#ifdef HAL_DAC_MODULE_ENABLED | |
#include "stm32f3xx_hal_dac.h" | |
#endif /* HAL_DAC_MODULE_ENABLED */ | |
#ifdef HAL_FLASH_MODULE_ENABLED | |
#include "stm32f3xx_hal_flash.h" | |
#endif /* HAL_FLASH_MODULE_ENABLED */ | |
#ifdef HAL_SRAM_MODULE_ENABLED | |
#include "stm32f3xx_hal_sram.h" | |
#endif /* HAL_SRAM_MODULE_ENABLED */ | |
#ifdef HAL_NOR_MODULE_ENABLED | |
#include "stm32f3xx_hal_nor.h" | |
#endif /* HAL_NOR_MODULE_ENABLED */ | |
#ifdef HAL_NAND_MODULE_ENABLED | |
#include "stm32f3xx_hal_nand.h" | |
#endif /* HAL_NAND_MODULE_ENABLED */ | |
#ifdef HAL_PCCARD_MODULE_ENABLED | |
#include "stm32f3xx_hal_pccard.h" | |
#endif /* HAL_PCCARD_MODULE_ENABLED */ | |
#ifdef HAL_HRTIM_MODULE_ENABLED | |
#include "stm32f3xx_hal_hrtim.h" | |
#endif /* HAL_HRTIM_MODULE_ENABLED */ | |
#ifdef HAL_I2C_MODULE_ENABLED | |
#include "stm32f3xx_hal_i2c.h" | |
#endif /* HAL_I2C_MODULE_ENABLED */ | |
#ifdef HAL_I2S_MODULE_ENABLED | |
#include "stm32f3xx_hal_i2s.h" | |
#endif /* HAL_I2S_MODULE_ENABLED */ | |
#ifdef HAL_IRDA_MODULE_ENABLED | |
#include "stm32f3xx_hal_irda.h" | |
#endif /* HAL_IRDA_MODULE_ENABLED */ | |
#ifdef HAL_IWDG_MODULE_ENABLED | |
#include "stm32f3xx_hal_iwdg.h" | |
#endif /* HAL_IWDG_MODULE_ENABLED */ | |
#ifdef HAL_OPAMP_MODULE_ENABLED | |
#include "stm32f3xx_hal_opamp.h" | |
#endif /* HAL_OPAMP_MODULE_ENABLED */ | |
#ifdef HAL_PCD_MODULE_ENABLED | |
#include "stm32f3xx_hal_pcd.h" | |
#endif /* HAL_PCD_MODULE_ENABLED */ | |
#ifdef HAL_PWR_MODULE_ENABLED | |
#include "stm32f3xx_hal_pwr.h" | |
#endif /* HAL_PWR_MODULE_ENABLED */ | |
#ifdef HAL_RTC_MODULE_ENABLED | |
#include "stm32f3xx_hal_rtc.h" | |
#endif /* HAL_RTC_MODULE_ENABLED */ | |
#ifdef HAL_SDADC_MODULE_ENABLED | |
#include "stm32f3xx_hal_sdadc.h" | |
#endif /* HAL_SDADC_MODULE_ENABLED */ | |
#ifdef HAL_SMARTCARD_MODULE_ENABLED | |
#include "stm32f3xx_hal_smartcard.h" | |
#endif /* HAL_SMARTCARD_MODULE_ENABLED */ | |
#ifdef HAL_SMBUS_MODULE_ENABLED | |
#include "stm32f3xx_hal_smbus.h" | |
#endif /* HAL_SMBUS_MODULE_ENABLED */ | |
#ifdef HAL_SPI_MODULE_ENABLED | |
#include "stm32f3xx_hal_spi.h" | |
#endif /* HAL_SPI_MODULE_ENABLED */ | |
#ifdef HAL_TIM_MODULE_ENABLED | |
#include "stm32f3xx_hal_tim.h" | |
#endif /* HAL_TIM_MODULE_ENABLED */ | |
#ifdef HAL_TSC_MODULE_ENABLED | |
#include "stm32f3xx_hal_tsc.h" | |
#endif /* HAL_TSC_MODULE_ENABLED */ | |
#ifdef HAL_UART_MODULE_ENABLED | |
#include "stm32f3xx_hal_uart.h" | |
#endif /* HAL_UART_MODULE_ENABLED */ | |
#ifdef HAL_USART_MODULE_ENABLED | |
#include "stm32f3xx_hal_usart.h" | |
#endif /* HAL_USART_MODULE_ENABLED */ | |
#ifdef HAL_WWDG_MODULE_ENABLED | |
#include "stm32f3xx_hal_wwdg.h" | |
#endif /* HAL_WWDG_MODULE_ENABLED */ | |
/* Exported macro ------------------------------------------------------------*/ | |
#ifdef USE_FULL_ASSERT | |
/** | |
* @brief The assert_param macro is used for function's parameters check. | |
* @param expr: If expr is false, it calls assert_failed function | |
* which reports the name of the source file and the source | |
* line number of the call that failed. | |
* If expr is true, it returns no value. | |
* @retval None | |
*/ | |
#define assert_param(expr) ((expr) ? (void)0U : assert_failed((char *)__FILE__, __LINE__)) | |
/* Exported functions ------------------------------------------------------- */ | |
void assert_failed(char* file, uint32_t line); | |
#else | |
#define assert_param(expr) ((void)0U) | |
#endif /* USE_FULL_ASSERT */ | |
#ifdef __cplusplus | |
} | |
#endif | |
#endif /* __STM32F3xx_HAL_CONF_H */ | |
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |