| /** | |
| ****************************************************************************** | |
| * @file stm32l1xx_hal_opamp.h | |
| * @author MCD Application Team | |
| * @brief Header file of OPAMP HAL module. | |
| ****************************************************************************** | |
| * @attention | |
| * | |
| * <h2><center>© COPYRIGHT(c) 2017 STMicroelectronics</center></h2> | |
| * | |
| * Redistribution and use in source and binary forms, with or without modification, | |
| * are permitted provided that the following conditions are met: | |
| * 1. Redistributions of source code must retain the above copyright notice, | |
| * this list of conditions and the following disclaimer. | |
| * 2. Redistributions in binary form must reproduce the above copyright notice, | |
| * this list of conditions and the following disclaimer in the documentation | |
| * and/or other materials provided with the distribution. | |
| * 3. Neither the name of STMicroelectronics nor the names of its contributors | |
| * may be used to endorse or promote products derived from this software | |
| * without specific prior written permission. | |
| * | |
| * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" | |
| * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE | |
| * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE | |
| * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE | |
| * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL | |
| * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR | |
| * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER | |
| * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, | |
| * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE | |
| * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. | |
| * | |
| ****************************************************************************** | |
| */ | |
| /* Define to prevent recursive inclusion -------------------------------------*/ | |
| #ifndef __STM32L1xx_HAL_OPAMP_H | |
| #define __STM32L1xx_HAL_OPAMP_H | |
| #ifdef __cplusplus | |
| extern "C" { | |
| #endif | |
| #if defined (STM32L151xCA) || defined (STM32L151xD) || defined (STM32L152xCA) || defined (STM32L152xD) || defined (STM32L162xCA) || defined (STM32L162xD) || defined (STM32L151xE) || defined (STM32L151xDX) || defined (STM32L152xE) || defined (STM32L152xDX) || defined (STM32L162xE) || defined (STM32L162xDX) || defined (STM32L162xC) || defined (STM32L152xC) || defined (STM32L151xC) | |
| /* Includes ------------------------------------------------------------------*/ | |
| #include "stm32l1xx_hal_def.h" | |
| /** @addtogroup STM32L1xx_HAL_Driver | |
| * @{ | |
| */ | |
| /** @addtogroup OPAMP | |
| * @{ | |
| */ | |
| /* Exported types ------------------------------------------------------------*/ | |
| /** @defgroup OPAMP_Exported_Types OPAMP Exported Types | |
| * @{ | |
| */ | |
| /** | |
| * @brief OPAMP Init structure definition | |
| */ | |
| typedef struct | |
| { | |
| uint32_t PowerSupplyRange; /*!< Specifies the power supply range: above or under 2.4V. | |
| This parameter must be a value of @ref OPAMP_PowerSupplyRange | |
| Caution: This parameter is common to all OPAMP instances: a modification of this parameter for the selected OPAMP impacts the other OPAMP instances. */ | |
| uint32_t PowerMode; /*!< Specifies the power mode Normal or Low-Power. | |
| This parameter must be a value of @ref OPAMP_PowerMode */ | |
| uint32_t Mode; /*!< Specifies the OPAMP mode | |
| This parameter must be a value of @ref OPAMP_Mode | |
| mode is either Standalone or Follower */ | |
| uint32_t InvertingInput; /*!< Specifies the inverting input in Standalone mode | |
| - In Standalone mode: i.e when mode is OPAMP_STANDALONE_MODE | |
| This parameter must be a value of @ref OPAMP_InvertingInput | |
| InvertingInput is either VM0 or VM1 | |
| - In Follower mode: i.e when mode is OPAMP_FOLLOWER_MODE | |
| This parameter is Not Applicable */ | |
| uint32_t NonInvertingInput; /*!< Specifies the non inverting input of the opamp: | |
| This parameter must be a value of @ref OPAMP_NonInvertingInput | |
| Note: Non-inverting input availability depends on OPAMP instance: | |
| OPAMP1: Non-inverting input is either IO0, DAC_Channel1 | |
| OPAMP2: Non-inverting input is either IO0, DAC_Channel1, DAC_Channel2 | |
| OPAMP3: Non-inverting input is either IO0, DAC_Channel2 (OPAMP3 availability depends on STM32L1 devices) */ | |
| uint32_t UserTrimming; /*!< Specifies the trimming mode | |
| This parameter must be a value of @ref OPAMP_UserTrimming | |
| UserTrimming is either factory or user trimming. | |
| Caution: This parameter is common to all OPAMP instances: a modification of this parameter for the selected OPAMP impacts the other OPAMP instances. */ | |
| uint32_t TrimmingValueP; /*!< Specifies the offset trimming value (PMOS) | |
| i.e. when UserTrimming is OPAMP_TRIMMING_USER. | |
| This parameter must be a number between Min_Data = 0 and Max_Data = 30 (Trimming value 31 is forbidden) | |
| 16 is typical default value */ | |
| uint32_t TrimmingValueN; /*!< Specifies the offset trimming value (NMOS) | |
| i.e. when UserTrimming is OPAMP_TRIMMING_USER. | |
| This parameter must be a number between Min_Data = 0 and Max_Data = 30 (Trimming value 31 is forbidden) | |
| 16 is typical default value */ | |
| uint32_t TrimmingValuePLowPower; /*!< Specifies the offset trimming value (PMOS) | |
| i.e. when UserTrimming is OPAMP_TRIMMING_USER. | |
| This parameter must be a number between Min_Data = 0 and Max_Data = 30 (Trimming value 31 is forbidden) | |
| 16 is typical default value */ | |
| uint32_t TrimmingValueNLowPower; /*!< Specifies the offset trimming value (NMOS) | |
| i.e. when UserTrimming is OPAMP_TRIMMING_USER. | |
| This parameter must be a number between Min_Data = 0 and Max_Data = 30 (Trimming value 31 is forbidden) | |
| 16 is typical default value */ | |
| }OPAMP_InitTypeDef; | |
| /** | |
| * @brief HAL State structures definition | |
| */ | |
| typedef enum | |
| { | |
| HAL_OPAMP_STATE_RESET = 0x00000000, /*!< OPMAP is not yet Initialized */ | |
| HAL_OPAMP_STATE_READY = 0x00000001, /*!< OPAMP is initialized and ready for use */ | |
| HAL_OPAMP_STATE_CALIBBUSY = 0x00000002, /*!< OPAMP is enabled in auto calibration mode */ | |
| HAL_OPAMP_STATE_BUSY = 0x00000004, /*!< OPAMP is enabled and running in normal mode */ | |
| HAL_OPAMP_STATE_BUSYLOCKED = 0x00000005, /*!< OPAMP is locked | |
| only system reset allows reconfiguring the opamp. */ | |
| }HAL_OPAMP_StateTypeDef; | |
| /** | |
| * @brief OPAMP Handle Structure definition | |
| */ | |
| typedef struct | |
| { | |
| OPAMP_TypeDef *Instance; /*!< OPAMP instance's registers base address */ | |
| OPAMP_InitTypeDef Init; /*!< OPAMP required parameters */ | |
| HAL_StatusTypeDef Status; /*!< OPAMP peripheral status */ | |
| HAL_LockTypeDef Lock; /*!< Locking object */ | |
| __IO HAL_OPAMP_StateTypeDef State; /*!< OPAMP communication state */ | |
| } OPAMP_HandleTypeDef; | |
| /** | |
| * @brief HAl_OPAMP_TrimmingValueTypeDef definition | |
| */ | |
| typedef uint32_t HAL_OPAMP_TrimmingValueTypeDef; | |
| /** | |
| * @} | |
| */ | |
| /* Exported constants --------------------------------------------------------*/ | |
| /** @defgroup OPAMP_Exported_Constants OPAMP Exported Constants | |
| * @{ | |
| */ | |
| /** | |
| * OTR register Mask | |
| */ | |
| #define OPAMP_TRIM_VALUE_MASK OPAMP_OTR_AO1_OPT_OFFSET_TRIM_LOW | |
| /** | |
| * CSR register Mask | |
| */ | |
| #define OPAMP_CSR_INSTANCE_OFFSET ( 8U) /* Offset of each OPAMP instance into register CSR */ | |
| #define OPAMP_OTR_INSTANCE_OFFSET (10U) /* Offset of each OPAMP instance into register OTR */ | |
| /** @defgroup OPAMP_Mode OPAMP Mode | |
| * @{ | |
| */ | |
| #define OPAMP_STANDALONE_MODE (0x00000000U) /*!< OPAMP standalone mode */ | |
| #define OPAMP_FOLLOWER_MODE (0x00000001U) /*!< OPAMP follower mode */ | |
| /** | |
| * @} | |
| */ | |
| /** @defgroup OPAMP_NonInvertingInput OPAMP NonInvertingInput | |
| * @{ | |
| */ | |
| #define OPAMP_NONINVERTINGINPUT_IO0 (0x00000000U) /*!< Comparator non-inverting input connected to dedicated IO pin low-leakage */ | |
| #define OPAMP_NONINVERTINGINPUT_DAC_CH1 (0x00000001U) /*!< Comparator non-inverting input connected internally to DAC channel 1. Available only on OPAMP1 and OPAMP2. */ | |
| #define OPAMP_NONINVERTINGINPUT_DAC_CH2 (0x00000002U) /*!< Comparator non-inverting input connected internally to DAC channel 2. Available only on OPAMP2 and OPAMP3 (OPAMP3 availability depends on STM32L1 devices). */ | |
| /** | |
| * @} | |
| */ | |
| /** @defgroup OPAMP_InvertingInput OPAMP InvertingInput | |
| * @{ | |
| */ | |
| /* Note: Literal "OPAMP_SEC_INVERTINGINPUT_IO1" is a legacy naming of "OPAMP_INVERTINGINPUT_IO1". It is equivalent and must be replaced by "OPAMP_INVERTINGINPUT_IO1". */ | |
| #define OPAMP_INVERTINGINPUT_IO0 (0x00000000U) /*!< Comparator inverting input connected to dedicated IO pin low-leakage */ | |
| #define OPAMP_INVERTINGINPUT_IO1 (0x00000001U) /*!< Comparator inverting input connected to alternative IO pin available on some device packages */ | |
| /** | |
| * @} | |
| */ | |
| /** @defgroup OPAMP_PowerMode OPAMP PowerMode | |
| * @{ | |
| */ | |
| #define OPAMP_POWERMODE_NORMAL (0x00000000U) | |
| #define OPAMP_POWERMODE_LOWPOWER (0x00000001U) | |
| /** | |
| * @} | |
| */ | |
| /** @defgroup OPAMP_PowerSupplyRange OPAMP PowerSupplyRange | |
| * @{ | |
| */ | |
| #define OPAMP_POWERSUPPLY_LOW (0x00000000U) /*!< Power supply range low (VDDA lower than 2.4V) */ | |
| #define OPAMP_POWERSUPPLY_HIGH OPAMP_CSR_AOP_RANGE /*!< Power supply range high (VDDA higher than 2.4V) */ | |
| /** | |
| * @} | |
| */ | |
| /** @defgroup OPAMP_UserTrimming OPAMP User Trimming | |
| * @{ | |
| */ | |
| #define OPAMP_TRIMMING_FACTORY (0x00000000U) /*!< Factory trimming */ | |
| #define OPAMP_TRIMMING_USER OPAMP_OTR_OT_USER /*!< User trimming */ | |
| /** | |
| * @} | |
| */ | |
| /** @defgroup OPAMP_FactoryTrimming OPAMP FactoryTrimming | |
| * @{ | |
| */ | |
| #define OPAMP_FACTORYTRIMMING_DUMMY (0xFFFFFFFFU) /*!< Dummy value if trimming value could not be retrieved */ | |
| #define OPAMP_FACTORYTRIMMING_P (0x00000000U) /*!< Offset trimming P */ | |
| #define OPAMP_FACTORYTRIMMING_N POSITION_VAL(OPAMP_OTR_AO1_OPT_OFFSET_TRIM_HIGH) /*!< Offset trimming N */ | |
| /** | |
| * @} | |
| */ | |
| /** | |
| * @} | |
| */ | |
| /* Private constants ---------------------------------------------------------*/ | |
| /** @defgroup OPAMP_Private_Constants OPAMP Private Constants | |
| * @{ | |
| */ | |
| /* Offset trimming time: during calibration, minimum time needed between two */ | |
| /* steps to have 1 mV accuracy. */ | |
| /* Refer to datasheet, electrical characteristics: parameter tOFFTRIM Typ=1ms.*/ | |
| /* Unit: ms. */ | |
| #define OPAMP_TRIMMING_DELAY ((uint32_t) 1) | |
| /** | |
| * @} | |
| */ | |
| /* Exported macros -----------------------------------------------------------*/ | |
| /** @defgroup OPAMP_Private_Macro OPAMP Private Macro | |
| * @{ | |
| */ | |
| /** @brief Reset OPAMP handle state | |
| * @param __HANDLE__: OPAMP handle. | |
| * @retval None | |
| */ | |
| #define __HAL_OPAMP_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_OPAMP_STATE_RESET) | |
| /** | |
| * @} | |
| */ | |
| /* Private macro -------------------------------------------------------------*/ | |
| /** @defgroup OPAMP_Private_Macro OPAMP Private Macro | |
| * @{ | |
| */ | |
| /** | |
| * @brief Select the OPAMP bit OPAxPD (power-down) corresponding to the | |
| * selected OPAMP instance. | |
| * @param __HANDLE__: OPAMP handle | |
| * @retval None | |
| */ | |
| #define OPAMP_CSR_OPAXPD(__HANDLE__) \ | |
| (OPAMP_CSR_OPA1PD << (OPAMP_INSTANCE_DECIMAL(__HANDLE__) * OPAMP_CSR_INSTANCE_OFFSET)) | |
| /** | |
| * @brief Select the OPAMP bit S3SELx (switch 3) corresponding to the | |
| * selected OPAMP instance. | |
| * @param __HANDLE__: OPAMP handle | |
| * @retval None | |
| */ | |
| #define OPAMP_CSR_S3SELX(__HANDLE__) \ | |
| (OPAMP_CSR_S3SEL1 << (OPAMP_INSTANCE_DECIMAL(__HANDLE__) * OPAMP_CSR_INSTANCE_OFFSET)) | |
| /** | |
| * @brief Select the OPAMP bit S4SELx (switch 4) corresponding to the | |
| * selected OPAMP instance. | |
| * @param __HANDLE__: OPAMP handle | |
| * @retval None | |
| */ | |
| #define OPAMP_CSR_S4SELX(__HANDLE__) \ | |
| (OPAMP_CSR_S4SEL1 << (OPAMP_INSTANCE_DECIMAL(__HANDLE__) * OPAMP_CSR_INSTANCE_OFFSET)) | |
| /** | |
| * @brief Select the OPAMP bit S5SELx (switch 5) corresponding to the | |
| * selected OPAMP instance. | |
| * @param __HANDLE__: OPAMP handle | |
| * @retval None | |
| */ | |
| #define OPAMP_CSR_S5SELX(__HANDLE__) \ | |
| (OPAMP_CSR_S5SEL1 << (OPAMP_INSTANCE_DECIMAL(__HANDLE__) * OPAMP_CSR_INSTANCE_OFFSET)) | |
| /** | |
| * @brief Select the OPAMP bit S3SELx (switch 6) corresponding to the | |
| * selected OPAMP instance. | |
| * @param __HANDLE__: OPAMP handle | |
| * @retval None | |
| */ | |
| #define OPAMP_CSR_S6SELX(__HANDLE__) \ | |
| (OPAMP_CSR_S6SEL1 << (OPAMP_INSTANCE_DECIMAL(__HANDLE__) * OPAMP_CSR_INSTANCE_OFFSET)) | |
| /** | |
| * @brief Select the OPAMP bit OPAxCAL_L (offset calibration for differential | |
| * pair P) corresponding to the selected OPAMP instance. | |
| * @param __HANDLE__: OPAMP handle | |
| * @retval None | |
| */ | |
| #define OPAMP_CSR_OPAXCAL_L(__HANDLE__) \ | |
| (OPAMP_CSR_OPA1CAL_L << (OPAMP_INSTANCE_DECIMAL(__HANDLE__) * OPAMP_CSR_INSTANCE_OFFSET)) | |
| /** | |
| * @brief Select the OPAMP bit OPAxCAL_H (offset calibration for differential | |
| * pair N) corresponding to the selected OPAMP instance. | |
| * @param __HANDLE__: OPAMP handle | |
| * @retval None | |
| */ | |
| #define OPAMP_CSR_OPAXCAL_H(__HANDLE__) \ | |
| (OPAMP_CSR_OPA1CAL_H << (OPAMP_INSTANCE_DECIMAL(__HANDLE__) * OPAMP_CSR_INSTANCE_OFFSET)) | |
| /** | |
| * @brief Select the OPAMP bit OPAxLPM (low power mode) corresponding to the | |
| * selected OPAMP instance. | |
| * @param __HANDLE__: OPAMP handle | |
| * @retval None | |
| */ | |
| #define OPAMP_CSR_OPAXLPM(__HANDLE__) \ | |
| (OPAMP_CSR_OPA1LPM << (OPAMP_INSTANCE_DECIMAL(__HANDLE__) * OPAMP_CSR_INSTANCE_OFFSET)) | |
| /** | |
| * @brief Select the OPAMP bits of all switches corresponding to the | |
| * selected OPAMP instance. | |
| * @param __HANDLE__: OPAMP handle | |
| * @retval None | |
| */ | |
| #define OPAMP_CSR_ALL_SWITCHES(__HANDLE__) \ | |
| ( ( ((__HANDLE__)->Instance != OPAMP2) \ | |
| )? \ | |
| ( \ | |
| ((OPAMP_CSR_S3SEL1 | OPAMP_CSR_S4SEL1 | OPAMP_CSR_S5SEL1 | OPAMP_CSR_S6SEL1) << (OPAMP_INSTANCE_DECIMAL(__HANDLE__) * OPAMP_CSR_INSTANCE_OFFSET)) \ | |
| | \ | |
| (OPAMP_CSR_ANAWSEL1 << (OPAMP_INSTANCE_DECIMAL(__HANDLE__))) \ | |
| ) \ | |
| : \ | |
| ( \ | |
| ((OPAMP_CSR_S3SEL1 | OPAMP_CSR_S4SEL1 | OPAMP_CSR_S5SEL1 | OPAMP_CSR_S6SEL1) << (OPAMP_INSTANCE_DECIMAL(__HANDLE__) * OPAMP_CSR_INSTANCE_OFFSET)) \ | |
| | \ | |
| (OPAMP_CSR_ANAWSEL1 << (OPAMP_INSTANCE_DECIMAL(__HANDLE__))) \ | |
| | \ | |
| (OPAMP_CSR_S7SEL2) \ | |
| ) \ | |
| ) | |
| /** | |
| * @brief Select the OPAMP bit ANAWSELx (switch SanA) corresponding to the | |
| * selected OPAMP instance. | |
| * @param __HANDLE__: OPAMP handle | |
| * @retval None | |
| */ | |
| #define OPAMP_CSR_ANAWSELX(__HANDLE__) \ | |
| (OPAMP_CSR_ANAWSEL1 << (OPAMP_INSTANCE_DECIMAL(__HANDLE__))) | |
| /** | |
| * @brief Select the OPAMP bit OPAxCALOUT in function of the selected | |
| * OPAMP instance. | |
| * @param __HANDLE__: OPAMP handle | |
| * @retval None | |
| */ | |
| #define OPAMP_CSR_OPAXCALOUT(__HANDLE__) \ | |
| (OPAMP_CSR_OPA1CALOUT << (OPAMP_INSTANCE_DECIMAL(__HANDLE__))) | |
| /** | |
| * @brief Select the OPAMP trimming bits position value (position of LSB) | |
| * in register OPAMP_OTR or register OPAMP_LPOTR in function of the selected | |
| * OPAMP instance and the transistors differential pair high (PMOS) or | |
| * low (NMOS). | |
| * @param __HANDLE__: OPAMP handle | |
| * @param __TRIM_HIGH_LOW__: transistors differential pair high or low. | |
| * Must be a value of @ref OPAMP_FactoryTrimming. | |
| * @retval None | |
| */ | |
| #define OPAMP_OFFSET_TRIM_BITSPOSITION(__HANDLE__, __TRIM_HIGH_LOW__) \ | |
| ((OPAMP_INSTANCE_DECIMAL((__HANDLE__)) * OPAMP_OTR_INSTANCE_OFFSET) + (__TRIM_HIGH_LOW__)) | |
| /** | |
| * @brief Shift the OPAMP trimming bits to register OPAMP_OTR or register | |
| * OPAMP_LPOTR in function of the selected OPAMP instance and the transistors | |
| * differential pair high (PMOS) or low (NMOS). | |
| * @param __HANDLE__: OPAMP handle | |
| * @param __TRIM_HIGH_LOW__: transistors differential pair high or low. | |
| * Must be a value of @ref OPAMP_FactoryTrimming. | |
| * @param __TRIMMING_VALUE__: Trimming value | |
| * @retval None | |
| */ | |
| #define OPAMP_OFFSET_TRIM_SET(__HANDLE__, __TRIM_HIGH_LOW__, __TRIMMING_VALUE__) \ | |
| ((__TRIMMING_VALUE__) << (OPAMP_OFFSET_TRIM_BITSPOSITION((__HANDLE__), (__TRIM_HIGH_LOW__)))) | |
| /** | |
| * @brief Check that trimming value is within correct range | |
| * @param TRIMMINGVALUE: OPAMP trimming value | |
| * @retval None | |
| */ | |
| #define IS_OPAMP_TRIMMINGVALUE(TRIMMINGVALUE) ((TRIMMINGVALUE) <= 0x1E) | |
| #define IS_OPAMP_FUNCTIONAL_NORMALMODE(INPUT) (((INPUT) == OPAMP_STANDALONE_MODE) || \ | |
| ((INPUT) == OPAMP_FOLLOWER_MODE)) | |
| #define IS_OPAMP_INVERTING_INPUT(INPUT) (((INPUT) == OPAMP_INVERTINGINPUT_IO0) || \ | |
| ((INPUT) == OPAMP_INVERTINGINPUT_IO1) ) | |
| #define IS_OPAMP_POWERMODE(TRIMMING) (((TRIMMING) == OPAMP_POWERMODE_NORMAL) || \ | |
| ((TRIMMING) == OPAMP_POWERMODE_LOWPOWER) ) | |
| #define IS_OPAMP_POWER_SUPPLY_RANGE(RANGE) (((RANGE) == OPAMP_POWERSUPPLY_LOW) || \ | |
| ((RANGE) == OPAMP_POWERSUPPLY_HIGH) ) | |
| #define IS_OPAMP_TRIMMING(TRIMMING) (((TRIMMING) == OPAMP_TRIMMING_FACTORY) || \ | |
| ((TRIMMING) == OPAMP_TRIMMING_USER)) | |
| #define IS_OPAMP_FACTORYTRIMMING(TRIMMING) (((TRIMMING) == OPAMP_FACTORYTRIMMING_N) || \ | |
| ((TRIMMING) == OPAMP_FACTORYTRIMMING_P) ) | |
| /** | |
| * @} | |
| */ | |
| /* Include OPAMP HAL Extension module */ | |
| #include "stm32l1xx_hal_opamp_ex.h" | |
| /* Exported functions --------------------------------------------------------*/ | |
| /** @addtogroup OPAMP_Exported_Functions | |
| * @{ | |
| */ | |
| /** @addtogroup OPAMP_Exported_Functions_Group1 | |
| * @{ | |
| */ | |
| /* Initialization/de-initialization functions **********************************/ | |
| HAL_StatusTypeDef HAL_OPAMP_Init(OPAMP_HandleTypeDef *hopamp); | |
| HAL_StatusTypeDef HAL_OPAMP_DeInit (OPAMP_HandleTypeDef *hopamp); | |
| void HAL_OPAMP_MspInit(OPAMP_HandleTypeDef *hopamp); | |
| void HAL_OPAMP_MspDeInit(OPAMP_HandleTypeDef *hopamp); | |
| /** | |
| * @} | |
| */ | |
| /** @addtogroup OPAMP_Exported_Functions_Group2 | |
| * @{ | |
| */ | |
| /* I/O operation functions *****************************************************/ | |
| HAL_StatusTypeDef HAL_OPAMP_Start(OPAMP_HandleTypeDef *hopamp); | |
| HAL_StatusTypeDef HAL_OPAMP_Stop(OPAMP_HandleTypeDef *hopamp); | |
| HAL_StatusTypeDef HAL_OPAMP_SelfCalibrate(OPAMP_HandleTypeDef *hopamp); | |
| /** | |
| * @} | |
| */ | |
| /** @addtogroup OPAMP_Exported_Functions_Group3 | |
| * @{ | |
| */ | |
| /* Peripheral Control functions ************************************************/ | |
| HAL_StatusTypeDef HAL_OPAMP_Lock(OPAMP_HandleTypeDef *hopamp); | |
| HAL_OPAMP_TrimmingValueTypeDef HAL_OPAMP_GetTrimOffset (OPAMP_HandleTypeDef *hopamp, uint32_t trimmingoffset); | |
| /** | |
| * @} | |
| */ | |
| /** @addtogroup OPAMP_Exported_Functions_Group4 | |
| * @{ | |
| */ | |
| /* Peripheral State functions **************************************************/ | |
| HAL_OPAMP_StateTypeDef HAL_OPAMP_GetState(OPAMP_HandleTypeDef *hopamp); | |
| /** | |
| * @} | |
| */ | |
| /** | |
| * @} | |
| */ | |
| /** | |
| * @} | |
| */ | |
| /** | |
| * @} | |
| */ | |
| #endif /* STM32L151xCA || STM32L151xD || STM32L152xCA || STM32L152xD || STM32L162xCA || STM32L162xD || STM32L151xE || STM32L151xDX || STM32L152xE || STM32L152xDX || STM32L162xE || STM32L162xDX || STM32L162xC || STM32L152xC || STM32L151xC */ | |
| #ifdef __cplusplus | |
| } | |
| #endif | |
| #endif /* __STM32L1xx_HAL_OPAMP_H */ | |
| /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |