/****************************************************************************
 * arch/xtensa/src/esp32s3/esp32s3_irq.c
 *
 * Licensed to the Apache Software Foundation (ASF) under one or more
 * contributor license agreements.  See the NOTICE file distributed with
 * this work for additional information regarding copyright ownership.  The
 * ASF licenses this file to you under the Apache License, Version 2.0 (the
 * "License"); you may not use this file except in compliance with the
 * License.  You may obtain a copy of the License at
 *
 *   http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
 * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.  See the
 * License for the specific language governing permissions and limitations
 * under the License.
 *
 ****************************************************************************/

/****************************************************************************
 * Included Files
 ****************************************************************************/

#include <nuttx/config.h>

#include <stdint.h>
#include <string.h>
#include <assert.h>
#include <errno.h>
#include <debug.h>

#include <nuttx/irq.h>
#include <nuttx/arch.h>
#include <nuttx/board.h>
#include <nuttx/kmalloc.h>
#include <arch/irq.h>
#include <arch/board/board.h>
#include <irq/irq.h>

#include "xtensa.h"

#include "esp32s3_gpio.h"
#include "esp32s3_rtc_gpio.h"
#include "esp32s3_irq.h"
#ifdef CONFIG_SMP
#include "esp32s3_smp.h"
#endif
#include "esp32s3_userspace.h"
#include "hardware/esp32s3_interrupt_core0.h"
#ifdef CONFIG_SMP
#include "hardware/esp32s3_interrupt_core1.h"
#endif
#include "hardware/esp32s3_soc.h"
#include "hardware/esp32s3_system.h"

/****************************************************************************
 * Pre-processor Definitions
 ****************************************************************************/

/* Interrupt stack definitions for SMP */

#if defined(CONFIG_SMP) && CONFIG_ARCH_INTERRUPTSTACK > 15
#  define INTSTACK_ALLOC (CONFIG_SMP_NCPUS * INTSTACK_SIZE)
#endif

/* IRQ to CPU and CPU interrupts mapping:
 *
 * Encoding: CIIIIIII
 *  C: CPU that enabled the interrupt (0 = PRO, 1 = APP).
 *  I: Associated CPU interrupt.
 */

#define IRQ_UNMAPPED            0xff
#define IRQ_GETCPU(m)           (((m) & 0x80) >> 0x07)
#define IRQ_GETCPUINT(m)        ((m) & 0x7f)
#define IRQ_MKMAP(c, i)         (((c) << 0x07) | (i))

/* CPU interrupts to peripheral mapping:
 *
 * Encoding: EPPPPPPP
 *  E: CPU interrupt status (0 = Disabled, 1 = Enabled).
 *  P: Attached peripheral.
 */

#define CPUINT_UNASSIGNED       0x7f
#define CPUINT_GETEN(m)         (((m) & 0x80) >> 0x07)
#define CPUINT_GETIRQ(m)        ((m) & 0x7f)
#define CPUINT_ASSIGN(c)        (((c) & 0x7f) | 0x80)
#define CPUINT_DISABLE(m)       ((m) & 0x7f)
#define CPUINT_ENABLE(m)        ((m) | 0x80)

/* Mapping Peripheral IDs to map register addresses. */

#define CORE0_MAP_REGADDR(n)    (DR_REG_INTERRUPT_CORE0_BASE + ((n) << 2))
#ifdef CONFIG_SMP
#  define CORE1_MAP_REGADDR(n)  (DR_REG_INTERRUPT_CORE1_BASE + ((n) << 2))
#endif

/* CPU interrupts can be detached from any peripheral source by setting the
 * map register to an internal CPU interrupt (6, 7, 11, 15, 16, or 29).
 */

#define NO_CPUINT               ESP32S3_CPUINT_TIMER0

/* Priority range is 1-5 */

#define ESP32S3_MIN_PRIORITY    1
#define ESP32S3_MAX_PRIORITY    5
#define ESP32S3_PRIO_INDEX(p)   ((p) - ESP32S3_MIN_PRIORITY)

#ifdef CONFIG_ESP32S3_WIFI
#  define ESP32S3_WIFI_RESERVE_INT  (1 << ESP32S3_CPUINT_MAC)
#else
#  define ESP32S3_WIFI_RESERVE_INT  0
#endif

#ifdef CONFIG_ESP32S3_BLE
#  define ESP32S3_BLE_RESERVE_INT ((1 << ESP32S3_CPUINT_BT_BB) | \
                                   (1 << ESP32S3_CPUINT_RWBLE))
#else
#  define ESP32S3_BLE_RESERVE_INT 0
#endif

/****************************************************************************
 * Public Data
 ****************************************************************************/

#if defined(CONFIG_SMP) && CONFIG_ARCH_INTERRUPTSTACK > 15
/* In the SMP configuration, we will need custom interrupt stacks.
 * These definitions provide the aligned stack allocations.
 */

static uint32_t g_intstackalloc[INTSTACK_ALLOC >> 2];

/* These definitions provide the "top" of the push-down stacks. */

uintptr_t g_cpu_intstack_top[CONFIG_SMP_NCPUS] =
{
  (uintptr_t)g_intstackalloc + INTSTACK_SIZE,
#if CONFIG_SMP_NCPUS > 1
  (uintptr_t)g_intstackalloc + (2 * INTSTACK_SIZE),
#endif /* CONFIG_SMP_NCPUS > 1 */
};
#endif /* defined(CONFIG_SMP) && CONFIG_ARCH_INTERRUPTSTACK > 15 */

/****************************************************************************
 * Private Data
 ****************************************************************************/

/* Maps a CPU interrupt to the IRQ of the attached peripheral interrupt */

static uint8_t g_cpu0_intmap[ESP32S3_NCPUINTS];
#ifdef CONFIG_SMP
static uint8_t g_cpu1_intmap[ESP32S3_NCPUINTS];
#endif

static volatile uint8_t g_irqmap[NR_IRQS];

/* g_intenable[] is a shadow copy of the per-CPU INTENABLE register
 * content.
 */

static uint32_t g_intenable[CONFIG_SMP_NCPUS];

/* g_non_iram_int_mask[] is a bitmask of the interrupts that should be
 * disabled during a SPI flash operation. Non-IRAM interrupts should always
 * be disabled, but interrupts place on IRAM are able to run during a SPI
 * flash operation.
 */

static uint32_t g_non_iram_int_mask[CONFIG_SMP_NCPUS];

/* g_non_iram_int_disabled[] keeps track of the interrupts disabled during
 * a SPI flash operation.
 */

static uint32_t g_non_iram_int_disabled[CONFIG_SMP_NCPUS];

/* Per-CPU flag to indicate that non-IRAM interrupts were disabled */

static bool g_non_iram_int_disabled_flag[CONFIG_SMP_NCPUS];

/* Bitsets for free, unallocated CPU interrupts available to peripheral
 * devices.
 */

static uint32_t g_cpu0_freeints = ESP32S3_CPUINT_PERIPHSET &
                                  ~(ESP32S3_WIFI_RESERVE_INT |
                                    ESP32S3_BLE_RESERVE_INT);

#ifdef CONFIG_SMP
static uint32_t g_cpu1_freeints = ESP32S3_CPUINT_PERIPHSET;
#endif

/* Bitsets for each interrupt priority 1-5 */

static const uint32_t g_priority[5] =
{
  ESP32S3_INTPRI1_MASK,
  ESP32S3_INTPRI2_MASK,
  ESP32S3_INTPRI3_MASK,
  ESP32S3_INTPRI4_MASK,
  ESP32S3_INTPRI5_MASK
};

#ifdef CONFIG_ESP32S3_IRAM_ISR_DEBUG
/* The g_iram_count keeps track of how many times such an IRQ ran when the
 * non-IRAM interrupts were disabled.
 */

static uint64_t g_iram_count[NR_IRQS];
#endif

/****************************************************************************
 * Private Functions
 ****************************************************************************/

/****************************************************************************
 * Name: xtensa_attach_fromcpu1_interrupt
 ****************************************************************************/

#ifdef CONFIG_SMP
static inline void xtensa_attach_fromcpu1_interrupt(void)
{
  int cpuint;

  /* Connect all CPU peripheral source to allocated CPU interrupt */

  cpuint = esp32s3_setup_irq(0, ESP32S3_PERIPH_INT_FROM_CPU1, 1,
                             ESP32S3_CPUINT_LEVEL);
  DEBUGASSERT(cpuint >= 0);

  /* Attach the inter-CPU interrupt. */

  irq_attach(ESP32S3_IRQ_INT_FROM_CPU1, (xcpt_t)esp32s3_fromcpu1_interrupt,
             NULL);

  /* Enable the inter-CPU interrupt. */

  up_enable_irq(ESP32S3_IRQ_INT_FROM_CPU1);
}
#endif

/****************************************************************************
 * Name: esp32s3_intinfo
 *
 * Description:
 *    Return the CPU interrupt map of the given CPU and the register map
 *    of the given peripheral.
 *
 ****************************************************************************/

static void esp32s3_intinfo(int cpu, int periphid,
                            uintptr_t *regaddr, uint8_t **intmap)
{
#ifdef CONFIG_SMP
  DEBUGASSERT(cpu >= 0 && cpu < CONFIG_SMP_NCPUS);

  if (cpu != 0)
    {
      *regaddr = CORE1_MAP_REGADDR(periphid);
      *intmap  = g_cpu1_intmap;
    }
  else
#endif
    {
      *regaddr = CORE0_MAP_REGADDR(periphid);
      *intmap  = g_cpu0_intmap;
    }
}

/****************************************************************************
 * Name:  esp32s3_getcpuint
 *
 * Description:
 *   Get a free CPU interrupt for a peripheral device.  This function will
 *   not ignore all of the pre-allocated CPU interrupts for internal
 *   devices.
 *
 * Input Parameters:
 *   cpu     - CPU core to query for CPU interrupt candidates
 *   intmask - mask of candidate CPU interrupts.  The CPU interrupt will be
 *             be allocated from free interrupts within this set
 *
 * Returned Value:
 *   On success, a CPU interrupt number is returned.
 *   A negated errno is returned on failure.
 *
 ****************************************************************************/

static int esp32s3_getcpuint(int cpu, uint32_t intmask)
{
  uint32_t *freeints;
  uint32_t bitmask;
  uint32_t intset;
  int cpuint;
  int ret = -ENOMEM;

  /* Check if there are CPU interrupts with the requested properties
   * available.
   */

#ifdef CONFIG_SMP
  if (cpu != 0)
    {
      freeints = &g_cpu1_freeints;
    }
  else
#endif
    {
      freeints = &g_cpu0_freeints;
    }

  intset = *freeints & intmask;
  if (intset != 0)
    {
      /* Skip over initial unavailable CPU interrupts quickly in groups
       * of 8 interrupt.
       */

      for (cpuint = 0, bitmask = 0xff;
           cpuint <= ESP32S3_CPUINT_MAX && (intset & bitmask) == 0;
           cpuint += 8, bitmask <<= 8);

      /* Search for an unallocated CPU interrupt number in the remaining
       * intset.
       */

      for (; cpuint <= ESP32S3_CPUINT_MAX; cpuint++)
        {
          /* If the bit corresponding to the CPU interrupt is '1', then
           * that CPU interrupt is available.
           */

          bitmask = 1ul << cpuint;
          if ((intset & bitmask) != 0)
            {
              /* Got it! */

              *freeints &= ~bitmask;
              ret = cpuint;
              break;
            }
        }
    }

  /* Enable the CPU interrupt now.  The interrupt is still not attached
   * to any peripheral and thus has no effect.
   */

  if (ret >= 0)
    {
      xtensa_enable_cpuint(&g_intenable[cpu], 1ul << ret);
    }

  return ret;
}

/****************************************************************************
 * Name:  esp32s3_alloc_cpuint
 *
 * Description:
 *   Allocate a level CPU interrupt
 *
 * Input Parameters:
 *   cpu      - CPU core to query for CPU interrupt candidates
 *   priority - Priority of the CPU interrupt (1-5)
 *   type     - Interrupt type (level or edge).
 *
 * Returned Value:
 *   On success, the allocated CPU interrupt number is returned.
 *   A negated errno is returned on failure.  The only possible failure
 *   is that all CPU interrupts of the requested type have already been
 *   allocated.
 *
 ****************************************************************************/

static int esp32s3_alloc_cpuint(int cpu, int priority, int type)
{
  uint32_t mask;

  DEBUGASSERT(priority >= ESP32S3_MIN_PRIORITY &&
              priority <= ESP32S3_MAX_PRIORITY);
  DEBUGASSERT(type == ESP32S3_CPUINT_LEVEL);

  /* Check if there are any level CPU interrupts available at the
   * requested interrupt priority.
   */

  mask = g_priority[ESP32S3_PRIO_INDEX(priority)] &
          ESP32S3_CPUINT_LEVELSET;

  return esp32s3_getcpuint(cpu, mask);
}

/****************************************************************************
 * Name:  esp32s3_free_cpuint
 *
 * Description:
 *   Free a previously allocated CPU interrupt
 *
 * Input Parameters:
 *   The CPU interrupt number to be freed
 *
 * Returned Value:
 *   None
 *
 ****************************************************************************/

static void esp32s3_free_cpuint(int cpuint)
{
  uint32_t *freeints;
  uint32_t bitmask;

  DEBUGASSERT(cpuint >= 0 && cpuint <= ESP32S3_CPUINT_MAX);

  /* Mark the CPU interrupt as available */

  bitmask  = 1ul << cpuint;

#ifdef CONFIG_SMP
  if (up_cpu_index() != 0)
    {
      freeints = &g_cpu1_freeints;
    }
  else
#endif
    {
      freeints = &g_cpu0_freeints;
    }

  DEBUGASSERT((*freeints & bitmask) == 0);
  *freeints |= bitmask;
}

#ifdef CONFIG_ESP32S3_IRAM_ISR_DEBUG

/****************************************************************************
 * Name:  esp32s3_iram_interrupt_record
 *
 * Description:
 *   This function keeps track of the IRQs that ran when non-IRAM interrupts
 *   are disabled and enables debugging of the IRAM-enabled interrupts.
 *
 * Input Parameters:
 *   irq - The IRQ associated with a CPU interrupt
 *
 * Returned Value:
 *   None.
 *
 ****************************************************************************/

void esp32s3_irq_iram_interrupt_record(int irq)
{
  irqstate_t flags = enter_critical_section();

  g_iram_count[irq]++;

  leave_critical_section(flags);
}
#endif

/****************************************************************************
 * Public Functions
 ****************************************************************************/

/****************************************************************************
 * Name: up_irqinitialize
 ****************************************************************************/

void up_irqinitialize(void)
{
  int i;

  /* All CPU ints are non-IRAM interrupts at the beginning and should be
   * disabled during a SPI flash operation
   */

  for (i = 0; i < CONFIG_SMP_NCPUS; i++)
    {
      g_non_iram_int_mask[i] = UINT32_MAX;
    }

  for (i = 0; i < NR_IRQS; i++)
    {
      g_irqmap[i] = IRQ_UNMAPPED;
    }

  /* Hard code special cases. */

  g_irqmap[XTENSA_IRQ_TIMER0] = IRQ_MKMAP(0, ESP32S3_CPUINT_TIMER0);
  g_irqmap[XTENSA_IRQ_SWINT]  = IRQ_MKMAP(0, ESP32S3_CPUINT_SOFTWARE1);
  g_irqmap[XTENSA_IRQ_SWINT]  = IRQ_MKMAP(1, ESP32S3_CPUINT_SOFTWARE1);

#ifdef CONFIG_ESP32S3_WIFI
  g_irqmap[ESP32S3_IRQ_MAC] = IRQ_MKMAP(0, ESP32S3_CPUINT_MAC);
  g_irqmap[ESP32S3_IRQ_PWR] = IRQ_MKMAP(0, ESP32S3_CPUINT_PWR);
#endif

#ifdef CONFIG_ESP32S3_BLE
  g_irqmap[ESP32S3_IRQ_BT_BB] = IRQ_MKMAP(0, ESP32S3_CPUINT_BT_BB);
  g_irqmap[ESP32S3_IRQ_RWBLE] = IRQ_MKMAP(0, ESP32S3_CPUINT_RWBLE);
#endif

  /* Initialize CPU interrupts */

  esp32s3_cpuint_initialize();

  /* Reserve CPU0 interrupt for some special drivers */

#ifdef CONFIG_ESP32S3_WIFI
  g_cpu0_intmap[ESP32S3_CPUINT_MAC] = CPUINT_ASSIGN(ESP32S3_IRQ_MAC);
  g_cpu0_intmap[ESP32S3_CPUINT_PWR] = CPUINT_ASSIGN(ESP32S3_IRQ_PWR);
  xtensa_enable_cpuint(&g_intenable[0], 1 << ESP32S3_CPUINT_MAC);
#endif

#ifdef CONFIG_ESP32S3_BLE
  g_cpu0_intmap[ESP32S3_CPUINT_BT_BB] = CPUINT_ASSIGN(ESP32S3_IRQ_BT_BB);
  g_cpu0_intmap[ESP32S3_CPUINT_RWBLE] = CPUINT_ASSIGN(ESP32S3_IRQ_RWBLE);
  xtensa_enable_cpuint(&g_intenable[0], 1 << ESP32S3_CPUINT_BT_BB);
  xtensa_enable_cpuint(&g_intenable[0], 1 << ESP32S3_CPUINT_RWBLE);
#endif

#ifdef CONFIG_SMP
  /* Attach and enable the inter-CPU interrupt */

  xtensa_attach_fromcpu1_interrupt();
#endif

  /* Initialize GPIO interrupt support */

  esp32s3_gpioirqinitialize();

  /* Initialize RTCIO interrupt support */

  esp32s3_rtcioirqinitialize();

  /* Initialize interrupt handler for the PMS violation ISR */

  esp32s3_pmsirqinitialize();

#ifndef CONFIG_SUPPRESS_INTERRUPTS
  /* And finally, enable interrupts.  Also clears PS.EXCM */

  up_irq_enable();
#endif

  /* Attach the software interrupt */

  irq_attach(XTENSA_IRQ_SWINT, (xcpt_t)xtensa_swint, NULL);

  /* Enable the software CPU interrupt. */

  up_enable_irq(XTENSA_IRQ_SWINT);
}

/****************************************************************************
 * Name: up_disable_irq
 *
 * Description:
 *   Disable the IRQ specified by 'irq'
 *
 ****************************************************************************/

void up_disable_irq(int irq)
{
  int cpu = IRQ_GETCPU(g_irqmap[irq]);
  int cpuint = IRQ_GETCPUINT(g_irqmap[irq]);

  if (g_irqmap[irq] == IRQ_UNMAPPED)
    {
      /* This interrupt is already disabled. */

      return;
    }

  DEBUGASSERT(cpuint >= 0 && cpuint <= ESP32S3_CPUINT_MAX);
  DEBUGASSERT(cpu >= 0 && cpu < CONFIG_SMP_NCPUS);

  if (irq < XTENSA_NIRQ_INTERNAL)
    {
      /* This is an internal CPU interrupt, it cannot be disabled using
       * the Interrupt Matrix.
       */

#ifdef CONFIG_SMP
      int me = up_cpu_index();
      if (me != cpu)
        {
          /* It was the other CPU that enabled this interrupt. */

          return;
        }
#endif

      xtensa_disable_cpuint(&g_intenable[cpu], 1ul << cpuint);
    }
  else
    {
      /* A peripheral interrupt, use the Interrupt Matrix to disable it. */

      int periph = ESP32S3_IRQ2PERIPH(irq);
      uintptr_t regaddr;
      uint8_t *intmap;

      DEBUGASSERT(periph >= 0 && periph < ESP32S3_NPERIPHERALS);
      esp32s3_intinfo(cpu, periph, &regaddr, &intmap);

      intmap[cpuint] = CPUINT_DISABLE(intmap[cpuint]);
      putreg32(NO_CPUINT, regaddr);
    }
}

/****************************************************************************
 * Name: up_enable_irq
 *
 * Description:
 *   Enable the IRQ specified by 'irq'
 *
 ****************************************************************************/

void up_enable_irq(int irq)
{
  int cpuint = IRQ_GETCPUINT(g_irqmap[irq]);

  DEBUGASSERT(cpuint >= 0 && cpuint <= ESP32S3_CPUINT_MAX);

  if (irq < XTENSA_NIRQ_INTERNAL)
    {
      /* For internal interrupts, use the current CPU.  We can't enable other
       * CPUs' internal interrupts.
       * The CPU interrupt can still be taken from the map as internal
       * interrupts have the same number for all CPUs.  In this case then
       * we are just overwriting the cpu part of the map.
       */

      int cpu = up_cpu_index();

      /* Enable the CPU interrupt now for internal CPU. */

      xtensa_enable_cpuint(&g_intenable[cpu], (1ul << cpuint));
    }
  else
    {
      /* Retrieve the CPU that enabled this interrupt from the IRQ map.
       *
       * For peripheral interrupts we rely on the interrupt matrix to manage
       * interrupts.  The interrupt matrix registers are available for both
       * CPUs.
       */

      int cpu = IRQ_GETCPU(g_irqmap[irq]);

      /* Check if the registered ISR for this IRQ is intended to be run from
       * IRAM. If so, check if its interrupt handler is located in IRAM.
       */

      bool isr_in_iram = !((g_non_iram_int_mask[cpu] & (1 << cpuint)) > 0);

      xcpt_t handler = g_irqvector[irq].handler;

      if (isr_in_iram && handler && !esp32s3_ptr_iram(handler))
        {
          irqerr("Interrupt handler isn't in IRAM (%08" PRIx32 ")",
                 (intptr_t)handler);
          PANIC();
        }

      DEBUGASSERT(cpu >= 0 && cpu < CONFIG_SMP_NCPUS);

      /* For peripheral interrupts, attach the interrupt to the peripheral;
       * the CPU interrupt was already enabled when allocated.
       */

      int periph = ESP32S3_IRQ2PERIPH(irq);
      uintptr_t regaddr;
      uint8_t *intmap;

      DEBUGASSERT(periph >= 0 && periph < ESP32S3_NPERIPHERALS);

      esp32s3_intinfo(cpu, periph, &regaddr, &intmap);

      intmap[cpuint] = CPUINT_ENABLE(intmap[cpuint]);
      putreg32(cpuint, regaddr);
    }
}

/****************************************************************************
 * Name: up_get_intstackbase
 *
 * Description:
 *   Return a pointer to the "alloc" the correct interrupt stack allocation
 *   for the current CPU.
 *
 ****************************************************************************/

#if defined(CONFIG_SMP) && CONFIG_ARCH_INTERRUPTSTACK > 15
uintptr_t up_get_intstackbase(int cpu)
{
  return g_cpu_intstack_top[cpu] - INTSTACK_SIZE;
}
#endif

/****************************************************************************
 * Name:  esp32s3_cpuint_initialize
 *
 * Description:
 *   Initialize CPU interrupts
 *
 * Input Parameters:
 *   None
 *
 * Returned Value:
 *   Zero (OK) is returned on success; A negated errno value is returned on
 *   any failure.
 *
 ****************************************************************************/

int esp32s3_cpuint_initialize(void)
{
  uintptr_t regaddr;
  uint8_t *intmap;
#ifdef CONFIG_SMP
  int cpu;
#endif
  int i;

#ifdef CONFIG_SMP
  /* Which CPU are we initializing */

  cpu = up_cpu_index();
  DEBUGASSERT(cpu >= 0 && cpu < CONFIG_SMP_NCPUS);
#endif

  /* Disable all CPU interrupts on this CPU */

  xtensa_disable_all();

  /* Detach all peripheral sources PRO CPU interrupts */

  for (i = 0; i < ESP32S3_NPERIPHERALS; i++)
    {
#ifdef CONFIG_SMP
      if (cpu != 0)
        {
          regaddr = CORE1_MAP_REGADDR(i);
        }
      else
#endif
        {
          regaddr = CORE0_MAP_REGADDR(i);
        }

      putreg32(NO_CPUINT, regaddr);
    }

  /* Initialize CPU interrupt-to-IRQ mapping table */

#ifdef CONFIG_SMP
  if (cpu != 0)
    {
      intmap = g_cpu1_intmap;
    }
  else
#endif
    {
      intmap = g_cpu0_intmap;
    }

  /* Indicate that no peripheral interrupts are assigned to CPU interrupts */

  memset(intmap, CPUINT_UNASSIGNED, ESP32S3_NCPUINTS);

  /* Special case the 6 internal interrupts.
   *
   *   CPU interrupt bit             IRQ number
   *   ----------------------------  ---------------------
   *   ESP32S3_CPUINT_TIMER0      6  XTENSA_IRQ_TIMER0  0
   *   ESP32S3_CPUINT_SOFTWARE0   7  Not yet defined
   *   ESP32S3_CPUINT_PROFILING  11  Not yet defined
   *   ESP32S3_CPUINT_TIMER1     15  XTENSA_IRQ_TIMER1  1
   *   ESP32S3_CPUINT_TIMER2     16  XTENSA_IRQ_TIMER2  2
   *   ESP32S3_CPUINT_SOFTWARE1  29  XTENSA_IRQ_SWINT   4
   */

  intmap[ESP32S3_CPUINT_TIMER0]    = CPUINT_ASSIGN(XTENSA_IRQ_TIMER0);
  intmap[ESP32S3_CPUINT_TIMER1]    = CPUINT_ASSIGN(XTENSA_IRQ_TIMER1);
  intmap[ESP32S3_CPUINT_TIMER2]    = CPUINT_ASSIGN(XTENSA_IRQ_TIMER2);
  intmap[ESP32S3_CPUINT_SOFTWARE1] = CPUINT_ASSIGN(XTENSA_IRQ_SWINT);

  return OK;
}

/****************************************************************************
 * Name:  esp32s3_setup_irq
 *
 * Description:
 *   This function sets up the IRQ. It allocates a CPU interrupt of the given
 *   priority and associated flags and attaches it to the given peripheral.
 *
 * Input Parameters:
 *   cpu      - The CPU to receive the interrupt 0=PRO CPU 1=APP CPU
 *   periphid - The peripheral number from irq.h to be assigned to
 *              a CPU interrupt.
 *   priority - Interrupt's priority (1 - 5).
 *   flags    - An ORred mask of the ESP32S3_CPUINT_FLAG_* defines. These
 *              restrict the choice of interrupts that this routine can
 *              choose from.
 *
 * Returned Value:
 *   The allocated CPU interrupt on success, a negated errno value on
 *   failure.
 *
 ****************************************************************************/

int esp32s3_setup_irq(int cpu, int periphid, int priority, int flags)
{
  irqstate_t irqstate;
  uintptr_t regaddr;
  uint8_t *intmap;
  int irq;
  int cpuint;

  if ((flags & ESP32S3_CPUINT_EDGE) != 0)
    {
      irqerr("Only level-enabled interrupts are available");
      return -EINVAL;
    }

  irqstate = enter_critical_section();

  /* Setting up an IRQ includes the following steps:
   *    1. Allocate a CPU interrupt.
   *    2. Check if its ISR is intended to run from IRAM.
   *    3. Attach that CPU interrupt to the peripheral.
   *    4. Map the CPU interrupt to the IRQ to ease searching later.
   */

  cpuint = esp32s3_alloc_cpuint(cpu, priority, ESP32S3_CPUINT_LEVEL);
  if (cpuint < 0)
    {
      irqerr("Unable to allocate CPU interrupt for priority=%d and flags=%d",
             priority, flags);
      leave_critical_section(irqstate);

      return cpuint;
    }

  irq = ESP32S3_PERIPH2IRQ(periphid);

  DEBUGASSERT(periphid >= 0 && periphid < ESP32S3_NPERIPHERALS);
  DEBUGASSERT(cpuint >= 0 && cpuint <= ESP32S3_CPUINT_MAX);

  esp32s3_intinfo(cpu, periphid, &regaddr, &intmap);

  DEBUGASSERT(intmap[cpuint] == CPUINT_UNASSIGNED);

  intmap[cpuint] = CPUINT_ASSIGN(periphid + XTENSA_IRQ_FIRSTPERIPH);
  g_irqmap[irq] = IRQ_MKMAP(cpu, cpuint);

  if ((flags & ESP32S3_CPUINT_FLAG_IRAM) != 0)
    {
      esp32s3_irq_set_iram_isr(irq);
    }
  else
    {
      esp32s3_irq_unset_iram_isr(irq);
    }

  putreg32(cpuint, regaddr);

  leave_critical_section(irqstate);

  return cpuint;
}

/****************************************************************************
 * Name:  esp32s3_teardown_irq
 *
 * Description:
 *   This function undoes the operations done by esp32s3_setup_irq.
 *   It detaches a peripheral interrupt from a CPU interrupt and frees the
 *   CPU interrupt.
 *
 * Input Parameters:
 *   cpu      - The CPU to receive the interrupt 0=PRO CPU 1=APP CPU
 *   periphid - The peripheral number from irq.h to be detached from the
 *              CPU interrupt.
 *   cpuint   - The CPU interrupt from which the peripheral interrupt will
 *              be detached.
 *
 * Returned Value:
 *   None
 *
 ****************************************************************************/

void esp32s3_teardown_irq(int cpu, int periphid, int cpuint)
{
  irqstate_t irqstate;
  uintptr_t regaddr;
  uint8_t *intmap;
  int irq;

  irqstate = enter_critical_section();

  /* Tearing down an IRQ includes the following steps:
   *   1. Free the previously allocated CPU interrupt.
   *   2. Detach the interrupt from the peripheral.
   *   3. Unmap the IRQ from the IRQ-to-cpuint map.
   */

  esp32s3_free_cpuint(cpuint);

  irq = ESP32S3_PERIPH2IRQ(periphid);

  DEBUGASSERT(periphid >= 0 && periphid < ESP32S3_NPERIPHERALS);

  esp32s3_intinfo(cpu, periphid, &regaddr, &intmap);

  DEBUGASSERT(intmap[cpuint] != CPUINT_UNASSIGNED);
  intmap[cpuint] = CPUINT_UNASSIGNED;
  g_irqmap[irq] = IRQ_UNMAPPED;

  putreg32(NO_CPUINT, regaddr);

  leave_critical_section(irqstate);
}

/****************************************************************************
 * Name:  esp32s3_getirq
 *
 * Description:
 *   This function returns the IRQ associated with a CPU interrupt
 *
 * Input Parameters:
 *   cpu    - The CPU core of the IRQ being queried
 *   cpuint - The CPU interrupt associated to the IRQ
 *
 * Returned Value:
 *   The IRQ associated with such CPU interrupt or CPUINT_UNASSIGNED if
 *   IRQ is not yet assigned to a CPU interrupt.
 *
 ****************************************************************************/

int esp32s3_getirq(int cpu, int cpuint)
{
  uint8_t *intmap;

#ifdef CONFIG_SMP
  /* Select PRO or APP CPU interrupt mapping table */

  if (cpu != 0)
    {
      intmap = g_cpu1_intmap;
    }
  else
#endif
    {
      intmap = g_cpu0_intmap;
    }

  return CPUINT_GETIRQ(intmap[cpuint]);
}

/****************************************************************************
 * Name:  esp32s3_getcpuint_from_irq
 *
 * Description:
 *   This function returns the CPU interrupt associated with an IRQ
 *
 * Input Parameters:
 *   irq - The IRQ associated with a CPU interrupt
 *   cpu - Pointer to store the CPU core of the CPU interrupt
 *
 * Returned Value:
 *   The CPU interrupt associated with such IRQ or IRQ_UNMAPPED if
 *   CPU interrupt is not mapped to an IRQ.
 *
 ****************************************************************************/

int esp32s3_getcpuint_from_irq(int irq, int *cpu)
{
  (*cpu) = (int)IRQ_GETCPU(g_irqmap[irq]);

  return IRQ_GETCPUINT(g_irqmap[irq]);
}

/****************************************************************************
 * Name: xtensa_int_decode
 *
 * Description:
 *   Determine the peripheral that generated the interrupt and dispatch
 *   handling to the registered interrupt handler via xtensa_irq_dispatch().
 *
 * Input Parameters:
 *   cpuints - Set of pending interrupts valid for this level
 *   regs    - Saves processor state on the stack
 *
 * Returned Value:
 *   Normally the same value as regs is returned.  But, in the event of an
 *   interrupt level context switch, the returned value will, instead point
 *   to the saved processor state in the TCB of the newly started task.
 *
 ****************************************************************************/

uint32_t *xtensa_int_decode(uint32_t cpuints, uint32_t *regs)
{
  uint8_t *intmap;
  uint32_t mask;
  int bit;
  int cpu;

#ifdef CONFIG_ARCH_LEDS_CPU_ACTIVITY
  board_autoled_on(LED_CPU);
#endif
  /* Select PRO or APP CPU interrupt mapping table */

  cpu = up_cpu_index();

#ifdef CONFIG_SMP
  if (cpu != 0)
    {
      intmap = g_cpu1_intmap;
    }
  else
#endif
    {
      intmap = g_cpu0_intmap;
    }

  /* Skip over zero bits, eight at a time */

  for (bit = 0, mask = 0xff;
       bit < ESP32S3_NCPUINTS && (cpuints & mask) == 0;
       bit += 8, mask <<= 8);

  /* Process each pending CPU interrupt */

  for (; bit < ESP32S3_NCPUINTS && cpuints != 0; bit++)
    {
      mask = 1 << bit;
      if ((cpuints & mask) != 0)
        {
          /* Extract the IRQ number from the mapping table */

          uint8_t irq = CPUINT_GETIRQ(intmap[bit]);

          DEBUGASSERT(CPUINT_GETEN(intmap[bit]));
          DEBUGASSERT(irq != CPUINT_UNASSIGNED);

#ifdef CONFIG_ESP32S3_IRAM_ISR_DEBUG
          /* Check if non-IRAM interrupts are disabled */

          if (esp32s3_irq_noniram_status(cpu) == 0)
            {
              /* Sum-up the IRAM-enabled counter associated with the IRQ */

              esp32s3_irq_iram_interrupt_record(irq);
            }
#endif

          /* Clear software or edge-triggered interrupt */

           xtensa_intclear(mask);

          /* Dispatch the CPU interrupt.
           *
           * NOTE that regs may be altered in the case of an interrupt
           * level context switch.
           */

          regs = xtensa_irq_dispatch((int)irq, regs);

          /* Clear the bit in the pending interrupt so that perhaps
           * we can exit the look early.
           */

          cpuints &= ~mask;
        }
    }

  UNUSED(cpu);

  return regs;
}

/****************************************************************************
 * Name:  esp32s3_irq_noniram_disable
 *
 * Description:
 *   Disable interrupts that aren't specifically marked as running from IRAM
 *
 * Input Parameters:
 *   None
 *
 * Input Parameters:
 *   None
 *
 ****************************************************************************/

void esp32s3_irq_noniram_disable(void)
{
  irqstate_t irqstate;
  int cpu;
  uint32_t oldint;
  uint32_t non_iram_ints;

  irqstate = enter_critical_section();
  cpu = up_cpu_index();
  non_iram_ints = g_non_iram_int_mask[cpu];

  ASSERT(!g_non_iram_int_disabled_flag[cpu]);

  g_non_iram_int_disabled_flag[cpu] = true;
  oldint = g_intenable[cpu];

  xtensa_disable_cpuint(&g_intenable[cpu], non_iram_ints);

  g_non_iram_int_disabled[cpu] = oldint & non_iram_ints;

  leave_critical_section(irqstate);
}

/****************************************************************************
 * Name:  esp32s3_irq_noniram_enable
 *
 * Description:
 *   Re-enable interrupts disabled by esp32s3_irq_noniram_disable
 *
 * Input Parameters:
 *   None
 *
 * Input Parameters:
 *   None
 *
 ****************************************************************************/

void esp32s3_irq_noniram_enable(void)
{
  irqstate_t irqstate;
  int cpu;
  uint32_t non_iram_ints;

  irqstate = enter_critical_section();
  cpu = up_cpu_index();
  non_iram_ints = g_non_iram_int_disabled[cpu];

  ASSERT(g_non_iram_int_disabled_flag[cpu]);

  g_non_iram_int_disabled_flag[cpu] = false;

  xtensa_enable_cpuint(&g_intenable[cpu], non_iram_ints);

  leave_critical_section(irqstate);
}

/****************************************************************************
 * Name:  esp32s3_irq_noniram_status
 *
 * Description:
 *   Get the current status of non-IRAM interrupts on a specific CPU core
 *
 * Input Parameters:
 *   cpu - The CPU to check the non-IRAM interrupts state
 *
 * Returned Value:
 *   true if non-IRAM interrupts are enabled, false otherwise.
 *
 ****************************************************************************/

bool esp32s3_irq_noniram_status(int cpu)
{
  DEBUGASSERT(cpu >= 0 && cpu < CONFIG_SMP_NCPUS);

  return !g_non_iram_int_disabled_flag[cpu];
}

/****************************************************************************
 * Name:  esp32s3_irq_set_iram_isr
 *
 * Description:
 *   Set the ISR associated to an IRQ as a IRAM-enabled ISR.
 *
 * Input Parameters:
 *   irq - The associated IRQ to set
 *
 * Returned Value:
 *   OK on success; A negated errno value on failure.
 *
 ****************************************************************************/

int esp32s3_irq_set_iram_isr(int irq)
{
  int cpu;
  int cpuint = esp32s3_getcpuint_from_irq(irq, &cpu);

  if (cpuint == IRQ_UNMAPPED)
    {
      return -EINVAL;
    }

  g_non_iram_int_mask[cpu] &= ~(1 << cpuint);

  return OK;
}

/****************************************************************************
 * Name:  esp32s3_irq_unset_iram_isr
 *
 * Description:
 *   Set the ISR associated to an IRQ as a non-IRAM ISR.
 *
 * Input Parameters:
 *   irq - The associated IRQ to set
 *
 * Returned Value:
 *   OK on success; A negated errno value on failure.
 *
 ****************************************************************************/

int esp32s3_irq_unset_iram_isr(int irq)
{
  int cpu;
  int cpuint = esp32s3_getcpuint_from_irq(irq, &cpu);

  if (cpuint == IRQ_UNMAPPED)
    {
      return -EINVAL;
    }

  g_non_iram_int_mask[cpu] |= (1 << cpuint);

  return OK;
}

#ifdef CONFIG_ESP32S3_IRAM_ISR_DEBUG

/****************************************************************************
 * Name:  esp32s3_get_iram_interrupt_records
 *
 * Description:
 *   This function copies the vector that keeps track of the IRQs that ran
 *   when non-IRAM interrupts were disabled.
 *
 * Input Parameters:
 *
 *   irq_count - A previously allocated pointer to store the counter of the
 *               interrupts that ran when non-IRAM interrupts were disabled.
 *
 * Returned Value:
 *   None
 *
 ****************************************************************************/

void esp32s3_get_iram_interrupt_records(uint64_t *irq_count)
{
  irqstate_t flags = enter_critical_section();

  memcpy(irq_count, &g_iram_count, sizeof(uint64_t) * NR_IRQS);

  leave_critical_section(flags);
}
#endif