| # Licensed to the Apache Software Foundation (ASF) under one |
| # or more contributor license agreements. See the NOTICE file |
| # distributed with this work for additional information |
| # regarding copyright ownership. The ASF licenses this file |
| # to you under the Apache License, Version 2.0 (the |
| # "License"); you may not use this file except in compliance |
| # with the License. You may obtain a copy of the License at |
| # |
| # http://www.apache.org/licenses/LICENSE-2.0 |
| # |
| # Unless required by applicable law or agreed to in writing, |
| # software distributed under the License is distributed on an |
| # "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY |
| # KIND, either express or implied. See the License for the |
| # specific language governing permissions and limitations |
| # under the License. |
| # |
| |
| # Package: hw/bsp/nrf52dk |
| |
| syscfg.defs: |
| MCU_NRF52832: |
| description: Shall be set to 1 by BSP if using nRF52832 |
| value: 0 |
| MCU_NRF52840: |
| description: Shall be set to 1 by BSP if using nRF52840 |
| value: 0 |
| |
| MCU_FLASH_MIN_WRITE_SIZE: |
| description: > |
| Specifies the required alignment for internal flash writes. |
| Used internally by the newt tool. |
| value: 1 |
| |
| MCU_DCDC_ENABLED: |
| description: > |
| Specifies whether or not to enable DC/DC regulator. This requires |
| external circuitry so is defined to be zero by default and |
| expected to be overridden by the BSP. |
| value: 0 |
| |
| # MCU peripherals definitions |
| I2C_0: |
| description: 'Enable nRF52xxx I2C (TWI) 0' |
| value: 0 |
| restrictions: |
| - "!SPI_0_MASTER" |
| - "!SPI_0_SLAVE" |
| I2C_0_PIN_SCL: |
| description: 'SCL pin for I2C_0' |
| value: '' |
| I2C_0_PIN_SDA: |
| description: 'SDA pin for I2C_0' |
| value: '' |
| I2C_0_FREQ_KHZ: |
| description: 'Frequency [kHz] for I2C_0' |
| value: 100 |
| |
| I2C_1: |
| description: 'Enable nRF52xxx I2C (TWI) 1' |
| value: 0 |
| restrictions: |
| - "!SPI_1_MASTER" |
| - "!SPI_1_SLAVE" |
| I2C_1_PIN_SCL: |
| description: 'SCL pin for I2C_1' |
| value: '' |
| I2C_1_PIN_SDA: |
| description: 'SDA pin for I2C_1' |
| value: '' |
| I2C_1_FREQ_KHZ: |
| description: 'Frequency [kHz] for I2C_1' |
| value: 100 |
| |
| SPI_0_MASTER: |
| description: 'Enable nRF52xxx SPI Master 0' |
| value: 0 |
| restrictions: |
| - "!SPI_0_SLAVE" |
| - "!I2C_0" |
| SPI_0_MASTER_PIN_SCK: |
| description: 'SCK pin for SPI_0_MASTER' |
| value: '' |
| SPI_0_MASTER_PIN_MOSI: |
| description: 'MOSI pin for SPI_0_MASTER' |
| value: '' |
| SPI_0_MASTER_PIN_MISO: |
| description: 'MISO pin for SPI_0_MASTER' |
| value: '' |
| |
| SPI_0_SLAVE: |
| description: 'Enable nRF52xxx SPI Slave 0' |
| value: 0 |
| restrictions: |
| - "!SPI_0_MASTER" |
| - "!I2C_0" |
| SPI_0_SLAVE_PIN_SCK: |
| description: 'SCK pin for SPI_0_SLAVE' |
| value: '' |
| SPI_0_SLAVE_PIN_MOSI: |
| description: 'MOSI pin for SPI_0_SLAVE' |
| value: '' |
| SPI_0_SLAVE_PIN_MISO: |
| description: 'MISO pin for SPI_0_SLAVE' |
| value: '' |
| SPI_0_SLAVE_PIN_SS: |
| description: 'SS pin for SPI_0_SLAVE' |
| value: '' |
| |
| SPI_1_MASTER: |
| description: 'Enable nRF52xxx SPI Master 1' |
| value: 0 |
| restrictions: |
| - "!SPI_1_SLAVE" |
| - "!I2C_1" |
| SPI_1_MASTER_PIN_SCK: |
| description: 'SCK pin for SPI_1_MASTER' |
| value: '' |
| SPI_1_MASTER_PIN_MOSI: |
| description: 'MOSI pin for SPI_1_MASTER' |
| value: '' |
| SPI_1_MASTER_PIN_MISO: |
| description: 'MISO pin for SPI_1_MASTER' |
| value: '' |
| |
| SPI_1_SLAVE: |
| description: 'Enable nRF52xxx SPI Slave 1' |
| value: 0 |
| restrictions: |
| - "!SPI_1_MASTER" |
| - "!I2C_1" |
| SPI_1_SLAVE_PIN_SCK: |
| description: 'SCK pin for SPI_1_SLAVE' |
| value: '' |
| SPI_1_SLAVE_PIN_MOSI: |
| description: 'MOSI pin for SPI_1_SLAVE' |
| value: '' |
| SPI_1_SLAVE_PIN_MISO: |
| description: 'MISO pin for SPI_1_SLAVE' |
| value: '' |
| SPI_1_SLAVE_PIN_SS: |
| description: 'SS pin for SPI_1_SLAVE' |
| value: '' |
| |
| SPI_2_MASTER: |
| description: 'Enable nRF52xxx SPI Master 2' |
| value: 0 |
| restrictions: |
| - "!SPI_2_SLAVE" |
| - "MCU_NRF52840" |
| SPI_2_MASTER_PIN_SCK: |
| description: 'SCK pin for SPI_2_MASTER' |
| value: '' |
| SPI_2_MASTER_PIN_MOSI: |
| description: 'MOSI pin for SPI_2_MASTER' |
| value: '' |
| SPI_2_MASTER_PIN_MISO: |
| description: 'MISO pin for SPI_2_MASTER' |
| value: '' |
| |
| SPI_2_SLAVE: |
| description: 'Enable nRF52xxx SPI Slave 2' |
| value: 0 |
| restrictions: |
| - "!SPI_2_MASTER" |
| - "MCU_NRF52840" |
| SPI_2_SLAVE_PIN_SCK: |
| description: 'SCK pin for SPI_2_SLAVE' |
| value: '' |
| SPI_2_SLAVE_PIN_MOSI: |
| description: 'MOSI pin for SPI_2_SLAVE' |
| value: '' |
| SPI_2_SLAVE_PIN_MISO: |
| description: 'MISO pin for SPI_2_SLAVE' |
| value: '' |
| SPI_2_SLAVE_PIN_SS: |
| description: 'SS pin for SPI_2_SLAVE' |
| value: '' |
| |
| ADC_0: |
| description: 'Enable nRF52xxx ADC 0' |
| value: 0 |
| |
| ADC_0_REFMV_0: |
| description: 'reference mV in AREF0 if used' |
| value: 0 |
| |
| PWM_0: |
| description: 'Enable nRF52xxx PWM 0' |
| value: 0 |
| PWM_1: |
| description: 'Enable nRF52xxx PWM 1' |
| value: 0 |
| PWM_2: |
| description: 'Enable nRF52xxx PWM 2' |
| value: 0 |
| PWM_3: |
| description: 'Enable nRF52xxx PWM 3' |
| value: 0 |
| restrictions: |
| - "MCU_NRF52840" |
| |
| TRNG: |
| description: 'Enable nRF52xxx TRNG' |
| value: 0 |
| |
| UART_0: |
| description: 'Enable nRF52xxx UART0' |
| value: 1 |
| UART_0_PIN_TX: |
| description: 'TX pin for UART0' |
| value: '' |
| UART_0_PIN_RX: |
| description: 'RX pin for UART0' |
| value: '' |
| UART_0_PIN_RTS: |
| description: 'RTS pin for UART0' |
| value: -1 |
| UART_0_PIN_CTS: |
| description: 'CTS pin for UART0' |
| value: -1 |
| |
| UART_1: |
| description: 'Enable nRF52xxx UART1' |
| value: 0 |
| restrictions: |
| - "MCU_NRF52840" |
| UART_1_PIN_TX: |
| description: 'TX pin for UART1' |
| value: '' |
| UART_1_PIN_RX: |
| description: 'RX pin for UART1' |
| value: '' |
| UART_1_PIN_RTS: |
| description: 'RTS pin for UART1' |
| value: -1 |
| UART_1_PIN_CTS: |
| description: 'CTS pin for UART1' |
| value: -1 |
| |
| TIMER_0: |
| description: 'Enable nRF52xxx Timer 0' |
| value: 1 |
| TIMER_1: |
| description: 'Enable nRF52xxx Timer 1' |
| value: 0 |
| TIMER_2: |
| description: 'Enable nRF52xxx Timer 2' |
| value: 0 |
| TIMER_3: |
| description: 'Enable nRF52xxx Timer 3' |
| value: 0 |
| TIMER_4: |
| description: 'Enable nRF52xxx Timer 4' |
| value: 0 |
| TIMER_5: |
| description: 'Enable nRF52xxx RTC 0' |
| value: 0 |
| |
| QSPI_ENABLE: |
| description: 'NRF52 QSPI' |
| value: 0 |
| |
| QSPI_READOC: |
| description: > |
| QSPI Command to use |
| 0 - 0x09 Fast Read |
| 1 - 0x3B Fast Read Dual Output |
| 2 - 0xBB Fast Read Dual I/O |
| 3 - 0x6B Fast Read Quad Output |
| 4 - 0xEB Fast Read Quad I/O |
| value: 0 |
| QSPI_WRITEOC: |
| description: > |
| QSPI Command to use |
| 0 - 0x02 Page program |
| 1 - 0xA2 Page program Dual Data |
| 2 - 0x32 Page program Quad Data |
| 3 - 0x38 Page program Quad I/O |
| value: 0 |
| QSPI_ADDRMODE: |
| description: 'Address lentgh 0=24 bits, 1=32 bits' |
| value: 0 |
| QSPI_DPMCONFIG: |
| description: 'Deep power mode enable' |
| value: 0 |
| QSPI_SCK_DELAY: |
| description: > |
| Minimum amount of time that the CSN pin must stay high |
| before it can go low again. Value is specified in number of 16 |
| MHz periods (62.5 ns). |
| value: 0 |
| QSPI_SCK_FREQ: |
| description: '32MHz clock divider (0-31). Clock = 32MHz / (1+divider)' |
| value: 0 |
| QSPI_SPI_MODE: |
| description: 'SPI 0=Mode0 or 1=Mode3' |
| value: 0 |
| |
| QSPI_FLASH_SECTOR_SIZE: |
| description: 'QSPI sector size. In most cases it should be 4096.' |
| value: 0 |
| QSPI_FLASH_PAGE_SIZE: |
| description: > |
| QSPI page size. Writes can only be perfrmed to one page at a time. |
| In most cases it should be 256. |
| value: 0 |
| |
| QSPI_FLASH_SECTOR_COUNT: |
| description: 'QSPI sector count' |
| value: -1 |
| QSPI_PIN_CS: |
| description: 'CS pin for QSPI' |
| value: -1 |
| QSPI_PIN_SCK: |
| description: 'SCK pin for QSPI' |
| value: -1 |
| QSPI_PIN_DIO0: |
| description: 'DIO0 pin for QSPI' |
| value: -1 |
| QSPI_PIN_DIO1: |
| description: 'DIO1 pin for QSPI' |
| value: -1 |
| QSPI_PIN_DIO2: |
| description: 'DIO2 pin for QSPI' |
| value: -1 |
| QSPI_PIN_DIO3: |
| description: 'DIO3 pin for QSPI' |
| value: -1 |
| |
| NFC_PINS_AS_GPIO: |
| description: 'Use NFC pins as GPIOs instead of NFC functionality' |
| value: 1 |
| |
| GPIO_AS_PIN_RESET: |
| description: 'Enable pin reset' |
| value: 0 |
| |
| |
| # The XTAL_xxx definitions are used to set the clock source used for the low |
| # frequency clock. It is required that at least one of these sources is |
| # enabled (the bsp should set one of these clock sources). |
| XTAL_32768: |
| description: 'External 32k oscillator LF clock source.' |
| value: 0 |
| restrictions: |
| - "!XTAL_32768_SYNTH" |
| - "!XTAL_RC" |
| |
| XTAL_RC: |
| description: 'internal RC LF clock source' |
| value: 0 |
| restrictions: |
| - "!XTAL_32768_SYNTH" |
| - "!XTAL_32768" |
| |
| XTAL_32768_SYNTH: |
| description: 'Synthesized 32k LF clock source.' |
| value: 0 |
| restrictions: |
| - "!XTAL_RC" |
| - "!XTAL_32768" |
| |
| syscfg.restrictions: |
| - "MCU_NRF52832 ^^ MCU_NRF52840" |
| - "!I2C_0 || (I2C_0_PIN_SCL && I2C_0_PIN_SDA)" |
| - "!I2C_1 || (I2C_1_PIN_SCL && I2C_1_PIN_SDA)" |
| - "!SPI_0_MASTER || (SPI_0_MASTER_PIN_SCK && SPI_0_MASTER_PIN_MOSI && SPI_0_MASTER_PIN_MISO)" |
| - "!SPI_1_MASTER || (SPI_1_MASTER_PIN_SCK && SPI_1_MASTER_PIN_MOSI && SPI_1_MASTER_PIN_MISO)" |
| - "!SPI_2_MASTER || (SPI_2_MASTER_PIN_SCK && SPI_2_MASTER_PIN_MOSI && SPI_2_MASTER_PIN_MISO)" |
| - "!SPI_0_SLAVE || (SPI_0_SLAVE_PIN_SCK && SPI_0_SLAVE_PIN_MOSI && SPI_0_SLAVE_PIN_MISO && SPI_0_SLAVE_PIN_SS)" |
| - "!SPI_1_SLAVE || (SPI_1_SLAVE_PIN_SCK && SPI_1_SLAVE_PIN_MOSI && SPI_1_SLAVE_PIN_MISO && SPI_1_SLAVE_PIN_SS)" |
| - "!SPI_2_SLAVE || (SPI_2_SLAVE_PIN_SCK && SPI_2_SLAVE_PIN_MOSI && SPI_2_SLAVE_PIN_MISO && SPI_2_SLAVE_PIN_SS)" |
| - "!UART_0 || (UART_0_PIN_TX && UART_0_PIN_RX)" |
| - "!UART_1 || (UART_1_PIN_TX && UART_1_PIN_RX)" |
