/** | |
****************************************************************************** | |
* @file stm32f3xx_hal_rcc.c | |
* @author MCD Application Team | |
* @brief RCC HAL module driver. | |
* This file provides firmware functions to manage the following | |
* functionalities of the Reset and Clock Control (RCC) peripheral: | |
* + Initialization and de-initialization functions | |
* + Peripheral Control functions | |
* | |
@verbatim | |
============================================================================== | |
##### RCC specific features ##### | |
============================================================================== | |
[..] | |
After reset the device is running from Internal High Speed oscillator | |
(HSI 8MHz) with Flash 0 wait state, Flash prefetch buffer is enabled, | |
and all peripherals are off except internal SRAM, Flash and JTAG. | |
(+) There is no prescaler on High speed (AHB) and Low speed (APB) buses; | |
all peripherals mapped on these buses are running at HSI speed. | |
(+) The clock for all peripherals is switched off, except the SRAM and FLASH. | |
(+) All GPIOs are in input floating state, except the JTAG pins which | |
are assigned to be used for debug purpose. | |
[..] Once the device started from reset, the user application has to: | |
(+) Configure the clock source to be used to drive the System clock | |
(if the application needs higher frequency/performance) | |
(+) Configure the System clock frequency and Flash settings | |
(+) Configure the AHB and APB buses prescalers | |
(+) Enable the clock for the peripheral(s) to be used | |
(+) Configure the clock source(s) for peripherals whose clocks are not | |
derived from the System clock (RTC, ADC, I2C, I2S, TIM, USB FS) | |
##### RCC Limitations ##### | |
============================================================================== | |
[..] | |
A delay between an RCC peripheral clock enable and the effective peripheral | |
enabling should be taken into account in order to manage the peripheral read/write | |
from/to registers. | |
(+) This delay depends on the peripheral mapping. | |
(++) AHB & APB peripherals, 1 dummy read is necessary | |
[..] | |
Workarounds: | |
(#) For AHB & APB peripherals, a dummy read to the peripheral register has been | |
inserted in each __HAL_RCC_PPP_CLK_ENABLE() macro. | |
@endverbatim | |
****************************************************************************** | |
* @attention | |
* | |
* <h2><center>© COPYRIGHT(c) 2016 STMicroelectronics</center></h2> | |
* | |
* Redistribution and use in source and binary forms, with or without modification, | |
* are permitted provided that the following conditions are met: | |
* 1. Redistributions of source code must retain the above copyright notice, | |
* this list of conditions and the following disclaimer. | |
* 2. Redistributions in binary form must reproduce the above copyright notice, | |
* this list of conditions and the following disclaimer in the documentation | |
* and/or other materials provided with the distribution. | |
* 3. Neither the name of STMicroelectronics nor the names of its contributors | |
* may be used to endorse or promote products derived from this software | |
* without specific prior written permission. | |
* | |
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" | |
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE | |
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE | |
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE | |
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL | |
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR | |
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER | |
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, | |
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE | |
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. | |
* | |
****************************************************************************** | |
*/ | |
/* Includes ------------------------------------------------------------------*/ | |
#include "stm32f3xx_hal.h" | |
/** @addtogroup STM32F3xx_HAL_Driver | |
* @{ | |
*/ | |
/** @defgroup RCC RCC | |
* @brief RCC HAL module driver | |
* @{ | |
*/ | |
#ifdef HAL_RCC_MODULE_ENABLED | |
/* Private typedef -----------------------------------------------------------*/ | |
/* Private define ------------------------------------------------------------*/ | |
/** @defgroup RCC_Private_Constants RCC Private Constants | |
* @{ | |
*/ | |
/* Bits position in in the CFGR register */ | |
#define RCC_CFGR_HPRE_BITNUMBER POSITION_VAL(RCC_CFGR_HPRE) | |
#define RCC_CFGR_PPRE1_BITNUMBER POSITION_VAL(RCC_CFGR_PPRE1) | |
#define RCC_CFGR_PPRE2_BITNUMBER POSITION_VAL(RCC_CFGR_PPRE2) | |
/** | |
* @} | |
*/ | |
/* Private macro -------------------------------------------------------------*/ | |
/** @defgroup RCC_Private_Macros RCC Private Macros | |
* @{ | |
*/ | |
#define MCO1_CLK_ENABLE() __HAL_RCC_GPIOA_CLK_ENABLE() | |
#define MCO1_GPIO_PORT GPIOA | |
#define MCO1_PIN GPIO_PIN_8 | |
/** | |
* @} | |
*/ | |
/* Private variables ---------------------------------------------------------*/ | |
/** @defgroup RCC_Private_Variables RCC Private Variables | |
* @{ | |
*/ | |
const uint8_t aPLLMULFactorTable[16] = { 2U, 3U, 4U, 5U, 6U, 7U, 8U, 9U, | |
10U, 11U, 12U, 13U, 14U, 15U, 16U, 16U}; | |
const uint8_t aPredivFactorTable[16] = { 1U, 2U, 3U, 4U, 5U, 6U, 7U, 8U, | |
9U,10U, 11U, 12U, 13U, 14U, 15U, 16U}; | |
/** | |
* @} | |
*/ | |
/* Private function prototypes -----------------------------------------------*/ | |
/* Exported functions ---------------------------------------------------------*/ | |
/** @defgroup RCC_Exported_Functions RCC Exported Functions | |
* @{ | |
*/ | |
/** @defgroup RCC_Exported_Functions_Group1 Initialization and de-initialization functions | |
* @brief Initialization and Configuration functions | |
* | |
@verbatim | |
=============================================================================== | |
##### Initialization and de-initialization functions ##### | |
=============================================================================== | |
[..] | |
This section provides functions allowing to configure the internal/external oscillators | |
(HSE, HSI, LSE, LSI, PLL, CSS and MCO) and the System buses clocks (SYSCLK, AHB, APB1 | |
and APB2). | |
[..] Internal/external clock and PLL configuration | |
(#) HSI (high-speed internal), 8 MHz factory-trimmed RC used directly or through | |
the PLL as System clock source. | |
The HSI clock can be used also to clock the USART and I2C peripherals. | |
(#) LSI (low-speed internal), ~40 KHz low consumption RC used as IWDG and/or RTC | |
clock source. | |
(#) HSE (high-speed external), 4 to 32 MHz crystal oscillator used directly or | |
through the PLL as System clock source. Can be used also as RTC clock source. | |
(#) LSE (low-speed external), 32 KHz oscillator used as RTC clock source. | |
(#) PLL (clocked by HSI or HSE), featuring different output clocks: | |
(++) The first output is used to generate the high speed system clock (up to 72 MHz) | |
(++) The second output is used to generate the clock for the USB FS (48 MHz) | |
(++) The third output may be used to generate the clock for the ADC peripherals (up to 72 MHz) | |
(++) The fourth output may be used to generate the clock for the TIM peripherals (144 MHz) | |
(#) CSS (Clock security system), once enable using the macro __HAL_RCC_CSS_ENABLE() | |
and if a HSE clock failure occurs(HSE used directly or through PLL as System | |
clock source), the System clocks automatically switched to HSI and an interrupt | |
is generated if enabled. The interrupt is linked to the Cortex-M4 NMI | |
(Non-Maskable Interrupt) exception vector. | |
(#) MCO (microcontroller clock output), used to output SYSCLK, HSI, HSE, LSI, LSE or PLL | |
clock (divided by 2) output on pin (such as PA8 pin). | |
[..] System, AHB and APB buses clocks configuration | |
(#) Several clock sources can be used to drive the System clock (SYSCLK): HSI, | |
HSE and PLL. | |
The AHB clock (HCLK) is derived from System clock through configurable | |
prescaler and used to clock the CPU, memory and peripherals mapped | |
on AHB bus (DMA, GPIO...). APB1 (PCLK1) and APB2 (PCLK2) clocks are derived | |
from AHB clock through configurable prescalers and used to clock | |
the peripherals mapped on these buses. You can use | |
"@ref HAL_RCC_GetSysClockFreq()" function to retrieve the frequencies of these clocks. | |
(#) All the peripheral clocks are derived from the System clock (SYSCLK) except: | |
(++) The FLASH program/erase clock which is always HSI 8MHz clock. | |
(++) The USB 48 MHz clock which is derived from the PLL VCO clock. | |
(++) The USART clock which can be derived as well from HSI 8MHz, LSI or LSE. | |
(++) The I2C clock which can be derived as well from HSI 8MHz clock. | |
(++) The ADC clock which is derived from PLL output. | |
(++) The RTC clock which is derived from the LSE, LSI or 1 MHz HSE_RTC | |
(HSE divided by a programmable prescaler). The System clock (SYSCLK) | |
frequency must be higher or equal to the RTC clock frequency. | |
(++) IWDG clock which is always the LSI clock. | |
(#) For the STM32F3xx devices, the maximum frequency of the SYSCLK, HCLK, PCLK1 and PCLK2 is 72 MHz, | |
Depending on the SYSCLK frequency, the flash latency should be adapted accordingly. | |
(#) After reset, the System clock source is the HSI (8 MHz) with 0 WS and | |
prefetch is disabled. | |
@endverbatim | |
* @{ | |
*/ | |
/* | |
Additional consideration on the SYSCLK based on Latency settings: | |
+-----------------------------------------------+ | |
| Latency | SYSCLK clock frequency (MHz) | | |
|---------------|-------------------------------| | |
|0WS(1CPU cycle)| 0 < SYSCLK <= 24 | | |
|---------------|-------------------------------| | |
|1WS(2CPU cycle)| 24 < SYSCLK <= 48 | | |
|---------------|-------------------------------| | |
|2WS(3CPU cycle)| 48 < SYSCLK <= 72 | | |
+-----------------------------------------------+ | |
*/ | |
/** | |
* @brief Resets the RCC clock configuration to the default reset state. | |
* @note The default reset state of the clock configuration is given below: | |
* - HSI ON and used as system clock source | |
* - HSE and PLL OFF | |
* - AHB, APB1 and APB2 prescaler set to 1. | |
* - CSS and MCO1 OFF | |
* - All interrupts disabled | |
* @note This function does not modify the configuration of the | |
* - Peripheral clocks | |
* - LSI, LSE and RTC clocks | |
* @retval None | |
*/ | |
void HAL_RCC_DeInit(void) | |
{ | |
/* Set HSION bit, HSITRIM[4:0] bits to the reset value*/ | |
SET_BIT(RCC->CR, RCC_CR_HSION | RCC_CR_HSITRIM_4); | |
/* Reset SW[1:0], HPRE[3:0], PPRE1[2:0], PPRE2[2:0] and MCOSEL[2:0] bits */ | |
CLEAR_BIT(RCC->CFGR, RCC_CFGR_SW | RCC_CFGR_HPRE | RCC_CFGR_PPRE1 | RCC_CFGR_PPRE2 | RCC_CFGR_MCO); | |
/* Reset HSEON, CSSON, PLLON bits */ | |
CLEAR_BIT(RCC->CR, RCC_CR_PLLON | RCC_CR_CSSON | RCC_CR_HSEON); | |
/* Reset HSEBYP bit */ | |
CLEAR_BIT(RCC->CR, RCC_CR_HSEBYP); | |
/* Reset CFGR register */ | |
CLEAR_REG(RCC->CFGR); | |
/* Reset CFGR2 register */ | |
CLEAR_REG(RCC->CFGR2); | |
/* Reset CFGR3 register */ | |
CLEAR_REG(RCC->CFGR3); | |
/* Disable all interrupts */ | |
CLEAR_REG(RCC->CIR); | |
/* Update the SystemCoreClock global variable */ | |
SystemCoreClock = HSI_VALUE; | |
} | |
/** | |
* @brief Initializes the RCC Oscillators according to the specified parameters in the | |
* RCC_OscInitTypeDef. | |
* @param RCC_OscInitStruct pointer to an RCC_OscInitTypeDef structure that | |
* contains the configuration information for the RCC Oscillators. | |
* @note The PLL is not disabled when used as system clock. | |
* @note Transitions LSE Bypass to LSE On and LSE On to LSE Bypass are not | |
* supported by this macro. User should request a transition to LSE Off | |
* first and then LSE On or LSE Bypass. | |
* @note Transition HSE Bypass to HSE On and HSE On to HSE Bypass are not | |
* supported by this macro. User should request a transition to HSE Off | |
* first and then HSE On or HSE Bypass. | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_RCC_OscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct) | |
{ | |
uint32_t tickstart = 0U; | |
/* Check the parameters */ | |
assert_param(RCC_OscInitStruct != NULL); | |
assert_param(IS_RCC_OSCILLATORTYPE(RCC_OscInitStruct->OscillatorType)); | |
/*------------------------------- HSE Configuration ------------------------*/ | |
if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_HSE) == RCC_OSCILLATORTYPE_HSE) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_HSE(RCC_OscInitStruct->HSEState)); | |
/* When the HSE is used as system clock or clock source for PLL in these cases it is not allowed to be disabled */ | |
if((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_HSE) | |
|| ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_PLLCLK) && (__HAL_RCC_GET_PLL_OSCSOURCE() == RCC_PLLSOURCE_HSE))) | |
{ | |
if((__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) != RESET) && (RCC_OscInitStruct->HSEState == RCC_HSE_OFF)) | |
{ | |
return HAL_ERROR; | |
} | |
} | |
else | |
{ | |
/* Set the new HSE configuration ---------------------------------------*/ | |
__HAL_RCC_HSE_CONFIG(RCC_OscInitStruct->HSEState); | |
#if defined(RCC_CFGR_PLLSRC_HSI_DIV2) | |
/* Configure the HSE predivision factor --------------------------------*/ | |
__HAL_RCC_HSE_PREDIV_CONFIG(RCC_OscInitStruct->HSEPredivValue); | |
#endif /* RCC_CFGR_PLLSRC_HSI_DIV2 */ | |
/* Check the HSE State */ | |
if(RCC_OscInitStruct->HSEState != RCC_HSE_OFF) | |
{ | |
/* Get Start Tick */ | |
tickstart = HAL_GetTick(); | |
/* Wait till HSE is ready */ | |
while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) == RESET) | |
{ | |
if((HAL_GetTick() - tickstart ) > HSE_TIMEOUT_VALUE) | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
else | |
{ | |
/* Get Start Tick */ | |
tickstart = HAL_GetTick(); | |
/* Wait till HSE is disabled */ | |
while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) != RESET) | |
{ | |
if((HAL_GetTick() - tickstart ) > HSE_TIMEOUT_VALUE) | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
} | |
} | |
/*----------------------------- HSI Configuration --------------------------*/ | |
if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_HSI) == RCC_OSCILLATORTYPE_HSI) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_HSI(RCC_OscInitStruct->HSIState)); | |
assert_param(IS_RCC_CALIBRATION_VALUE(RCC_OscInitStruct->HSICalibrationValue)); | |
/* Check if HSI is used as system clock or as PLL source when PLL is selected as system clock */ | |
if((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_HSI) | |
|| ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_SYSCLKSOURCE_STATUS_PLLCLK) && (__HAL_RCC_GET_PLL_OSCSOURCE() == RCC_PLLSOURCE_HSI))) | |
{ | |
/* When HSI is used as system clock it will not disabled */ | |
if((__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) != RESET) && (RCC_OscInitStruct->HSIState != RCC_HSI_ON)) | |
{ | |
return HAL_ERROR; | |
} | |
/* Otherwise, just the calibration is allowed */ | |
else | |
{ | |
/* Adjusts the Internal High Speed oscillator (HSI) calibration value.*/ | |
__HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->HSICalibrationValue); | |
} | |
} | |
else | |
{ | |
/* Check the HSI State */ | |
if(RCC_OscInitStruct->HSIState != RCC_HSI_OFF) | |
{ | |
/* Enable the Internal High Speed oscillator (HSI). */ | |
__HAL_RCC_HSI_ENABLE(); | |
/* Get Start Tick */ | |
tickstart = HAL_GetTick(); | |
/* Wait till HSI is ready */ | |
while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) == RESET) | |
{ | |
if((HAL_GetTick() - tickstart ) > HSI_TIMEOUT_VALUE) | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
/* Adjusts the Internal High Speed oscillator (HSI) calibration value.*/ | |
__HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->HSICalibrationValue); | |
} | |
else | |
{ | |
/* Disable the Internal High Speed oscillator (HSI). */ | |
__HAL_RCC_HSI_DISABLE(); | |
/* Get Start Tick */ | |
tickstart = HAL_GetTick(); | |
/* Wait till HSI is disabled */ | |
while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) != RESET) | |
{ | |
if((HAL_GetTick() - tickstart ) > HSI_TIMEOUT_VALUE) | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
} | |
} | |
/*------------------------------ LSI Configuration -------------------------*/ | |
if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_LSI) == RCC_OSCILLATORTYPE_LSI) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_LSI(RCC_OscInitStruct->LSIState)); | |
/* Check the LSI State */ | |
if(RCC_OscInitStruct->LSIState != RCC_LSI_OFF) | |
{ | |
/* Enable the Internal Low Speed oscillator (LSI). */ | |
__HAL_RCC_LSI_ENABLE(); | |
/* Get Start Tick */ | |
tickstart = HAL_GetTick(); | |
/* Wait till LSI is ready */ | |
while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSIRDY) == RESET) | |
{ | |
if((HAL_GetTick() - tickstart ) > LSI_TIMEOUT_VALUE) | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
else | |
{ | |
/* Disable the Internal Low Speed oscillator (LSI). */ | |
__HAL_RCC_LSI_DISABLE(); | |
/* Get Start Tick */ | |
tickstart = HAL_GetTick(); | |
/* Wait till LSI is disabled */ | |
while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSIRDY) != RESET) | |
{ | |
if((HAL_GetTick() - tickstart ) > LSI_TIMEOUT_VALUE) | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
} | |
/*------------------------------ LSE Configuration -------------------------*/ | |
if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_LSE) == RCC_OSCILLATORTYPE_LSE) | |
{ | |
FlagStatus pwrclkchanged = RESET; | |
/* Check the parameters */ | |
assert_param(IS_RCC_LSE(RCC_OscInitStruct->LSEState)); | |
/* Update LSE configuration in Backup Domain control register */ | |
/* Requires to enable write access to Backup Domain of necessary */ | |
if(__HAL_RCC_PWR_IS_CLK_DISABLED()) | |
{ | |
__HAL_RCC_PWR_CLK_ENABLE(); | |
pwrclkchanged = SET; | |
} | |
if(HAL_IS_BIT_CLR(PWR->CR, PWR_CR_DBP)) | |
{ | |
/* Enable write access to Backup domain */ | |
SET_BIT(PWR->CR, PWR_CR_DBP); | |
/* Wait for Backup domain Write protection disable */ | |
tickstart = HAL_GetTick(); | |
while(HAL_IS_BIT_CLR(PWR->CR, PWR_CR_DBP)) | |
{ | |
if((HAL_GetTick() - tickstart) > RCC_DBP_TIMEOUT_VALUE) | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
/* Set the new LSE configuration -----------------------------------------*/ | |
__HAL_RCC_LSE_CONFIG(RCC_OscInitStruct->LSEState); | |
/* Check the LSE State */ | |
if(RCC_OscInitStruct->LSEState != RCC_LSE_OFF) | |
{ | |
/* Get Start Tick */ | |
tickstart = HAL_GetTick(); | |
/* Wait till LSE is ready */ | |
while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) == RESET) | |
{ | |
if((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE) | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
else | |
{ | |
/* Get Start Tick */ | |
tickstart = HAL_GetTick(); | |
/* Wait till LSE is disabled */ | |
while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) != RESET) | |
{ | |
if((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE) | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
/* Require to disable power clock if necessary */ | |
if(pwrclkchanged == SET) | |
{ | |
__HAL_RCC_PWR_CLK_DISABLE(); | |
} | |
} | |
/*-------------------------------- PLL Configuration -----------------------*/ | |
/* Check the parameters */ | |
assert_param(IS_RCC_PLL(RCC_OscInitStruct->PLL.PLLState)); | |
if ((RCC_OscInitStruct->PLL.PLLState) != RCC_PLL_NONE) | |
{ | |
/* Check if the PLL is used as system clock or not */ | |
if(__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_PLLCLK) | |
{ | |
if((RCC_OscInitStruct->PLL.PLLState) == RCC_PLL_ON) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_RCC_PLLSOURCE(RCC_OscInitStruct->PLL.PLLSource)); | |
assert_param(IS_RCC_PLL_MUL(RCC_OscInitStruct->PLL.PLLMUL)); | |
#if defined(RCC_CFGR_PLLSRC_HSI_PREDIV) | |
assert_param(IS_RCC_PREDIV(RCC_OscInitStruct->PLL.PREDIV)); | |
#endif | |
/* Disable the main PLL. */ | |
__HAL_RCC_PLL_DISABLE(); | |
/* Get Start Tick */ | |
tickstart = HAL_GetTick(); | |
/* Wait till PLL is disabled */ | |
while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) != RESET) | |
{ | |
if((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE) | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
#if defined(RCC_CFGR_PLLSRC_HSI_PREDIV) | |
/* Configure the main PLL clock source, predivider and multiplication factor. */ | |
__HAL_RCC_PLL_CONFIG(RCC_OscInitStruct->PLL.PLLSource, | |
RCC_OscInitStruct->PLL.PREDIV, | |
RCC_OscInitStruct->PLL.PLLMUL); | |
#else | |
/* Configure the main PLL clock source and multiplication factor. */ | |
__HAL_RCC_PLL_CONFIG(RCC_OscInitStruct->PLL.PLLSource, | |
RCC_OscInitStruct->PLL.PLLMUL); | |
#endif /* RCC_CFGR_PLLSRC_HSI_PREDIV */ | |
/* Enable the main PLL. */ | |
__HAL_RCC_PLL_ENABLE(); | |
/* Get Start Tick */ | |
tickstart = HAL_GetTick(); | |
/* Wait till PLL is ready */ | |
while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) == RESET) | |
{ | |
if((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE) | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
else | |
{ | |
/* Disable the main PLL. */ | |
__HAL_RCC_PLL_DISABLE(); | |
/* Get Start Tick */ | |
tickstart = HAL_GetTick(); | |
/* Wait till PLL is disabled */ | |
while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) != RESET) | |
{ | |
if((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE) | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
} | |
else | |
{ | |
return HAL_ERROR; | |
} | |
} | |
return HAL_OK; | |
} | |
/** | |
* @brief Initializes the CPU, AHB and APB buses clocks according to the specified | |
* parameters in the RCC_ClkInitStruct. | |
* @param RCC_ClkInitStruct pointer to an RCC_OscInitTypeDef structure that | |
* contains the configuration information for the RCC peripheral. | |
* @param FLatency FLASH Latency | |
* The value of this parameter depend on device used within the same series | |
* @note The SystemCoreClock CMSIS variable is used to store System Clock Frequency | |
* and updated by @ref HAL_RCC_GetHCLKFreq() function called within this function | |
* | |
* @note The HSI is used (enabled by hardware) as system clock source after | |
* start-up from Reset, wake-up from STOP and STANDBY mode, or in case | |
* of failure of the HSE used directly or indirectly as system clock | |
* (if the Clock Security System CSS is enabled). | |
* | |
* @note A switch from one clock source to another occurs only if the target | |
* clock source is ready (clock stable after start-up delay or PLL locked). | |
* If a clock source which is not yet ready is selected, the switch will | |
* occur when the clock source will be ready. | |
* You can use @ref HAL_RCC_GetClockConfig() function to know which clock is | |
* currently used as system clock source. | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_RCC_ClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t FLatency) | |
{ | |
uint32_t tickstart = 0U; | |
/* Check the parameters */ | |
assert_param(RCC_ClkInitStruct != NULL); | |
assert_param(IS_RCC_CLOCKTYPE(RCC_ClkInitStruct->ClockType)); | |
assert_param(IS_FLASH_LATENCY(FLatency)); | |
/* To correctly read data from FLASH memory, the number of wait states (LATENCY) | |
must be correctly programmed according to the frequency of the CPU clock | |
(HCLK) of the device. */ | |
/* Increasing the number of wait states because of higher CPU frequency */ | |
if(FLatency > (FLASH->ACR & FLASH_ACR_LATENCY)) | |
{ | |
/* Program the new number of wait states to the LATENCY bits in the FLASH_ACR register */ | |
__HAL_FLASH_SET_LATENCY(FLatency); | |
/* Check that the new number of wait states is taken into account to access the Flash | |
memory by reading the FLASH_ACR register */ | |
if((FLASH->ACR & FLASH_ACR_LATENCY) != FLatency) | |
{ | |
return HAL_ERROR; | |
} | |
} | |
/*-------------------------- HCLK Configuration --------------------------*/ | |
if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_HCLK) == RCC_CLOCKTYPE_HCLK) | |
{ | |
assert_param(IS_RCC_HCLK(RCC_ClkInitStruct->AHBCLKDivider)); | |
MODIFY_REG(RCC->CFGR, RCC_CFGR_HPRE, RCC_ClkInitStruct->AHBCLKDivider); | |
} | |
/*------------------------- SYSCLK Configuration ---------------------------*/ | |
if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_SYSCLK) == RCC_CLOCKTYPE_SYSCLK) | |
{ | |
assert_param(IS_RCC_SYSCLKSOURCE(RCC_ClkInitStruct->SYSCLKSource)); | |
/* HSE is selected as System Clock Source */ | |
if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_HSE) | |
{ | |
/* Check the HSE ready flag */ | |
if(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) == RESET) | |
{ | |
return HAL_ERROR; | |
} | |
} | |
/* PLL is selected as System Clock Source */ | |
else if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_PLLCLK) | |
{ | |
/* Check the PLL ready flag */ | |
if(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) == RESET) | |
{ | |
return HAL_ERROR; | |
} | |
} | |
/* HSI is selected as System Clock Source */ | |
else | |
{ | |
/* Check the HSI ready flag */ | |
if(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) == RESET) | |
{ | |
return HAL_ERROR; | |
} | |
} | |
__HAL_RCC_SYSCLK_CONFIG(RCC_ClkInitStruct->SYSCLKSource); | |
/* Get Start Tick */ | |
tickstart = HAL_GetTick(); | |
if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_HSE) | |
{ | |
while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_HSE) | |
{ | |
if((HAL_GetTick() - tickstart ) > CLOCKSWITCH_TIMEOUT_VALUE) | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
else if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_PLLCLK) | |
{ | |
while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_PLLCLK) | |
{ | |
if((HAL_GetTick() - tickstart ) > CLOCKSWITCH_TIMEOUT_VALUE) | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
else | |
{ | |
while (__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_SYSCLKSOURCE_STATUS_HSI) | |
{ | |
if((HAL_GetTick() - tickstart ) > CLOCKSWITCH_TIMEOUT_VALUE) | |
{ | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
} | |
/* Decreasing the number of wait states because of lower CPU frequency */ | |
if(FLatency < (FLASH->ACR & FLASH_ACR_LATENCY)) | |
{ | |
/* Program the new number of wait states to the LATENCY bits in the FLASH_ACR register */ | |
__HAL_FLASH_SET_LATENCY(FLatency); | |
/* Check that the new number of wait states is taken into account to access the Flash | |
memory by reading the FLASH_ACR register */ | |
if((FLASH->ACR & FLASH_ACR_LATENCY) != FLatency) | |
{ | |
return HAL_ERROR; | |
} | |
} | |
/*-------------------------- PCLK1 Configuration ---------------------------*/ | |
if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_PCLK1) == RCC_CLOCKTYPE_PCLK1) | |
{ | |
assert_param(IS_RCC_PCLK(RCC_ClkInitStruct->APB1CLKDivider)); | |
MODIFY_REG(RCC->CFGR, RCC_CFGR_PPRE1, RCC_ClkInitStruct->APB1CLKDivider); | |
} | |
/*-------------------------- PCLK2 Configuration ---------------------------*/ | |
if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_PCLK2) == RCC_CLOCKTYPE_PCLK2) | |
{ | |
assert_param(IS_RCC_PCLK(RCC_ClkInitStruct->APB2CLKDivider)); | |
MODIFY_REG(RCC->CFGR, RCC_CFGR_PPRE2, ((RCC_ClkInitStruct->APB2CLKDivider) << 3U)); | |
} | |
/* Update the SystemCoreClock global variable */ | |
SystemCoreClock = HAL_RCC_GetSysClockFreq() >> AHBPrescTable[(RCC->CFGR & RCC_CFGR_HPRE)>> RCC_CFGR_HPRE_BITNUMBER]; | |
/* Configure the source of time base considering new system clocks settings*/ | |
HAL_InitTick (TICK_INT_PRIORITY); | |
return HAL_OK; | |
} | |
/** | |
* @} | |
*/ | |
/** @defgroup RCC_Exported_Functions_Group2 Peripheral Control functions | |
* @brief RCC clocks control functions | |
* | |
@verbatim | |
=============================================================================== | |
##### Peripheral Control functions ##### | |
=============================================================================== | |
[..] | |
This subsection provides a set of functions allowing to control the RCC Clocks | |
frequencies. | |
@endverbatim | |
* @{ | |
*/ | |
#if defined(RCC_CFGR_MCOPRE) | |
/** | |
* @brief Selects the clock source to output on MCO pin. | |
* @note MCO pin should be configured in alternate function mode. | |
* @param RCC_MCOx specifies the output direction for the clock source. | |
* This parameter can be one of the following values: | |
* @arg @ref RCC_MCO1 Clock source to output on MCO1 pin(PA8). | |
* @param RCC_MCOSource specifies the clock source to output. | |
* This parameter can be one of the following values: | |
* @arg @ref RCC_MCO1SOURCE_NOCLOCK No clock selected | |
* @arg @ref RCC_MCO1SOURCE_SYSCLK System Clock selected as MCO clock | |
* @arg @ref RCC_MCO1SOURCE_HSI HSI selected as MCO clock | |
* @arg @ref RCC_MCO1SOURCE_HSE HSE selected as MCO clock | |
* @arg @ref RCC_MCO1SOURCE_LSI LSI selected as MCO clock | |
* @arg @ref RCC_MCO1SOURCE_LSE LSE selected as MCO clock | |
* @arg @ref RCC_MCO1SOURCE_PLLCLK PLLCLK selected as MCO clock | |
* @arg @ref RCC_MCO1SOURCE_PLLCLK_DIV2 PLLCLK Divided by 2 selected as MCO clock | |
* @param RCC_MCODiv specifies the MCO DIV. | |
* This parameter can be one of the following values: | |
* @arg @ref RCC_MCODIV_1 no division applied to MCO clock | |
* @arg @ref RCC_MCODIV_2 division by 2 applied to MCO clock | |
* @arg @ref RCC_MCODIV_4 division by 4 applied to MCO clock | |
* @arg @ref RCC_MCODIV_8 division by 8 applied to MCO clock | |
* @arg @ref RCC_MCODIV_16 division by 16 applied to MCO clock | |
* @arg @ref RCC_MCODIV_32 division by 32 applied to MCO clock | |
* @arg @ref RCC_MCODIV_64 division by 64 applied to MCO clock | |
* @arg @ref RCC_MCODIV_128 division by 128 applied to MCO clock | |
* @retval None | |
*/ | |
#else | |
/** | |
* @brief Selects the clock source to output on MCO pin. | |
* @note MCO pin should be configured in alternate function mode. | |
* @param RCC_MCOx specifies the output direction for the clock source. | |
* This parameter can be one of the following values: | |
* @arg @ref RCC_MCO1 Clock source to output on MCO1 pin(PA8). | |
* @param RCC_MCOSource specifies the clock source to output. | |
* This parameter can be one of the following values: | |
* @arg @ref RCC_MCO1SOURCE_NOCLOCK No clock selected as MCO clock | |
* @arg @ref RCC_MCO1SOURCE_SYSCLK System clock selected as MCO clock | |
* @arg @ref RCC_MCO1SOURCE_HSI HSI selected as MCO clock | |
* @arg @ref RCC_MCO1SOURCE_HSE HSE selected as MCO clock | |
* @arg @ref RCC_MCO1SOURCE_LSI LSI selected as MCO clock | |
* @arg @ref RCC_MCO1SOURCE_LSE LSE selected as MCO clock | |
* @arg @ref RCC_MCO1SOURCE_PLLCLK_DIV2 PLLCLK Divided by 2 selected as MCO clock | |
* @param RCC_MCODiv specifies the MCO DIV. | |
* This parameter can be one of the following values: | |
* @arg @ref RCC_MCODIV_1 no division applied to MCO clock | |
* @retval None | |
*/ | |
#endif | |
void HAL_RCC_MCOConfig(uint32_t RCC_MCOx, uint32_t RCC_MCOSource, uint32_t RCC_MCODiv) | |
{ | |
GPIO_InitTypeDef gpio; | |
/* Check the parameters */ | |
assert_param(IS_RCC_MCO(RCC_MCOx)); | |
assert_param(IS_RCC_MCODIV(RCC_MCODiv)); | |
assert_param(IS_RCC_MCO1SOURCE(RCC_MCOSource)); | |
/* Configure the MCO1 pin in alternate function mode */ | |
gpio.Mode = GPIO_MODE_AF_PP; | |
gpio.Speed = GPIO_SPEED_FREQ_HIGH; | |
gpio.Pull = GPIO_NOPULL; | |
gpio.Pin = MCO1_PIN; | |
gpio.Alternate = GPIO_AF0_MCO; | |
/* MCO1 Clock Enable */ | |
MCO1_CLK_ENABLE(); | |
HAL_GPIO_Init(MCO1_GPIO_PORT, &gpio); | |
/* Configure the MCO clock source */ | |
__HAL_RCC_MCO1_CONFIG(RCC_MCOSource, RCC_MCODiv); | |
} | |
/** | |
* @brief Enables the Clock Security System. | |
* @note If a failure is detected on the HSE oscillator clock, this oscillator | |
* is automatically disabled and an interrupt is generated to inform the | |
* software about the failure (Clock Security System Interrupt, CSSI), | |
* allowing the MCU to perform rescue operations. The CSSI is linked to | |
* the Cortex-M4 NMI (Non-Maskable Interrupt) exception vector. | |
* @retval None | |
*/ | |
void HAL_RCC_EnableCSS(void) | |
{ | |
*(__IO uint32_t *) RCC_CR_CSSON_BB = (uint32_t)ENABLE; | |
} | |
/** | |
* @brief Disables the Clock Security System. | |
* @retval None | |
*/ | |
void HAL_RCC_DisableCSS(void) | |
{ | |
*(__IO uint32_t *) RCC_CR_CSSON_BB = (uint32_t)DISABLE; | |
} | |
/** | |
* @brief Returns the SYSCLK frequency | |
* @note The system frequency computed by this function is not the real | |
* frequency in the chip. It is calculated based on the predefined | |
* constant and the selected clock source: | |
* @note If SYSCLK source is HSI, function returns values based on HSI_VALUE(*) | |
* @note If SYSCLK source is HSE, function returns a value based on HSE_VALUE | |
* divided by PREDIV factor(**) | |
* @note If SYSCLK source is PLL, function returns a value based on HSE_VALUE | |
* divided by PREDIV factor(**) or HSI_VALUE(*) multiplied by the PLL factor. | |
* @note (*) HSI_VALUE is a constant defined in stm32f3xx_hal_conf.h file (default value | |
* 8 MHz) but the real value may vary depending on the variations | |
* in voltage and temperature. | |
* @note (**) HSE_VALUE is a constant defined in stm32f3xx_hal_conf.h file (default value | |
* 8 MHz), user has to ensure that HSE_VALUE is same as the real | |
* frequency of the crystal used. Otherwise, this function may | |
* have wrong result. | |
* | |
* @note The result of this function could be not correct when using fractional | |
* value for HSE crystal. | |
* | |
* @note This function can be used by the user application to compute the | |
* baud-rate for the communication peripherals or configure other parameters. | |
* | |
* @note Each time SYSCLK changes, this function must be called to update the | |
* right SYSCLK value. Otherwise, any configuration based on this function will be incorrect. | |
* | |
* @retval SYSCLK frequency | |
*/ | |
uint32_t HAL_RCC_GetSysClockFreq(void) | |
{ | |
uint32_t tmpreg = 0U, prediv = 0U, pllclk = 0U, pllmul = 0U; | |
uint32_t sysclockfreq = 0U; | |
tmpreg = RCC->CFGR; | |
/* Get SYSCLK source -------------------------------------------------------*/ | |
switch (tmpreg & RCC_CFGR_SWS) | |
{ | |
case RCC_SYSCLKSOURCE_STATUS_HSE: /* HSE used as system clock */ | |
{ | |
sysclockfreq = HSE_VALUE; | |
break; | |
} | |
case RCC_SYSCLKSOURCE_STATUS_PLLCLK: /* PLL used as system clock */ | |
{ | |
pllmul = aPLLMULFactorTable[(uint32_t)(tmpreg & RCC_CFGR_PLLMUL) >> POSITION_VAL(RCC_CFGR_PLLMUL)]; | |
prediv = aPredivFactorTable[(uint32_t)(RCC->CFGR2 & RCC_CFGR2_PREDIV) >> POSITION_VAL(RCC_CFGR2_PREDIV)]; | |
#if defined(RCC_CFGR_PLLSRC_HSI_DIV2) | |
if ((tmpreg & RCC_CFGR_PLLSRC) != RCC_PLLSOURCE_HSI) | |
{ | |
/* HSE used as PLL clock source : PLLCLK = HSE/PREDIV * PLLMUL */ | |
pllclk = (HSE_VALUE / prediv) * pllmul; | |
} | |
else | |
{ | |
/* HSI used as PLL clock source : PLLCLK = HSI/2 * PLLMUL */ | |
pllclk = (HSI_VALUE >> 1U) * pllmul; | |
} | |
#else | |
if ((tmpreg & RCC_CFGR_PLLSRC_HSE_PREDIV) == RCC_CFGR_PLLSRC_HSE_PREDIV) | |
{ | |
/* HSE used as PLL clock source : PLLCLK = HSE/PREDIV * PLLMUL */ | |
pllclk = (HSE_VALUE / prediv) * pllmul; | |
} | |
else | |
{ | |
/* HSI used as PLL clock source : PLLCLK = HSI/PREDIV * PLLMUL */ | |
pllclk = (HSI_VALUE / prediv) * pllmul; | |
} | |
#endif /* RCC_CFGR_PLLSRC_HSI_DIV2 */ | |
sysclockfreq = pllclk; | |
break; | |
} | |
case RCC_SYSCLKSOURCE_STATUS_HSI: /* HSI used as system clock source */ | |
default: /* HSI used as system clock */ | |
{ | |
sysclockfreq = HSI_VALUE; | |
break; | |
} | |
} | |
return sysclockfreq; | |
} | |
/** | |
* @brief Returns the HCLK frequency | |
* @note Each time HCLK changes, this function must be called to update the | |
* right HCLK value. Otherwise, any configuration based on this function will be incorrect. | |
* | |
* @note The SystemCoreClock CMSIS variable is used to store System Clock Frequency | |
* and updated within this function | |
* @retval HCLK frequency | |
*/ | |
uint32_t HAL_RCC_GetHCLKFreq(void) | |
{ | |
return SystemCoreClock; | |
} | |
/** | |
* @brief Returns the PCLK1 frequency | |
* @note Each time PCLK1 changes, this function must be called to update the | |
* right PCLK1 value. Otherwise, any configuration based on this function will be incorrect. | |
* @retval PCLK1 frequency | |
*/ | |
uint32_t HAL_RCC_GetPCLK1Freq(void) | |
{ | |
/* Get HCLK source and Compute PCLK1 frequency ---------------------------*/ | |
return (HAL_RCC_GetHCLKFreq() >> APBPrescTable[(RCC->CFGR & RCC_CFGR_PPRE1) >> RCC_CFGR_PPRE1_BITNUMBER]); | |
} | |
/** | |
* @brief Returns the PCLK2 frequency | |
* @note Each time PCLK2 changes, this function must be called to update the | |
* right PCLK2 value. Otherwise, any configuration based on this function will be incorrect. | |
* @retval PCLK2 frequency | |
*/ | |
uint32_t HAL_RCC_GetPCLK2Freq(void) | |
{ | |
/* Get HCLK source and Compute PCLK2 frequency ---------------------------*/ | |
return (HAL_RCC_GetHCLKFreq()>> APBPrescTable[(RCC->CFGR & RCC_CFGR_PPRE2) >> RCC_CFGR_PPRE2_BITNUMBER]); | |
} | |
/** | |
* @brief Configures the RCC_OscInitStruct according to the internal | |
* RCC configuration registers. | |
* @param RCC_OscInitStruct pointer to an RCC_OscInitTypeDef structure that | |
* will be configured. | |
* @retval None | |
*/ | |
void HAL_RCC_GetOscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct) | |
{ | |
/* Check the parameters */ | |
assert_param(RCC_OscInitStruct != NULL); | |
/* Set all possible values for the Oscillator type parameter ---------------*/ | |
RCC_OscInitStruct->OscillatorType = RCC_OSCILLATORTYPE_HSE | RCC_OSCILLATORTYPE_HSI \ | |
| RCC_OSCILLATORTYPE_LSE | RCC_OSCILLATORTYPE_LSI; | |
/* Get the HSE configuration -----------------------------------------------*/ | |
if((RCC->CR &RCC_CR_HSEBYP) == RCC_CR_HSEBYP) | |
{ | |
RCC_OscInitStruct->HSEState = RCC_HSE_BYPASS; | |
} | |
else if((RCC->CR &RCC_CR_HSEON) == RCC_CR_HSEON) | |
{ | |
RCC_OscInitStruct->HSEState = RCC_HSE_ON; | |
} | |
else | |
{ | |
RCC_OscInitStruct->HSEState = RCC_HSE_OFF; | |
} | |
#if defined(RCC_CFGR_PLLSRC_HSI_DIV2) | |
RCC_OscInitStruct->HSEPredivValue = __HAL_RCC_HSE_GET_PREDIV(); | |
#endif | |
/* Get the HSI configuration -----------------------------------------------*/ | |
if((RCC->CR &RCC_CR_HSION) == RCC_CR_HSION) | |
{ | |
RCC_OscInitStruct->HSIState = RCC_HSI_ON; | |
} | |
else | |
{ | |
RCC_OscInitStruct->HSIState = RCC_HSI_OFF; | |
} | |
RCC_OscInitStruct->HSICalibrationValue = (uint32_t)((RCC->CR & RCC_CR_HSITRIM) >> POSITION_VAL(RCC_CR_HSITRIM)); | |
/* Get the LSE configuration -----------------------------------------------*/ | |
if((RCC->BDCR &RCC_BDCR_LSEBYP) == RCC_BDCR_LSEBYP) | |
{ | |
RCC_OscInitStruct->LSEState = RCC_LSE_BYPASS; | |
} | |
else if((RCC->BDCR &RCC_BDCR_LSEON) == RCC_BDCR_LSEON) | |
{ | |
RCC_OscInitStruct->LSEState = RCC_LSE_ON; | |
} | |
else | |
{ | |
RCC_OscInitStruct->LSEState = RCC_LSE_OFF; | |
} | |
/* Get the LSI configuration -----------------------------------------------*/ | |
if((RCC->CSR &RCC_CSR_LSION) == RCC_CSR_LSION) | |
{ | |
RCC_OscInitStruct->LSIState = RCC_LSI_ON; | |
} | |
else | |
{ | |
RCC_OscInitStruct->LSIState = RCC_LSI_OFF; | |
} | |
/* Get the PLL configuration -----------------------------------------------*/ | |
if((RCC->CR &RCC_CR_PLLON) == RCC_CR_PLLON) | |
{ | |
RCC_OscInitStruct->PLL.PLLState = RCC_PLL_ON; | |
} | |
else | |
{ | |
RCC_OscInitStruct->PLL.PLLState = RCC_PLL_OFF; | |
} | |
RCC_OscInitStruct->PLL.PLLSource = (uint32_t)(RCC->CFGR & RCC_CFGR_PLLSRC); | |
RCC_OscInitStruct->PLL.PLLMUL = (uint32_t)(RCC->CFGR & RCC_CFGR_PLLMUL); | |
#if defined(RCC_CFGR_PLLSRC_HSI_PREDIV) | |
RCC_OscInitStruct->PLL.PREDIV = (uint32_t)(RCC->CFGR2 & RCC_CFGR2_PREDIV); | |
#endif /* RCC_CFGR_PLLSRC_HSI_PREDIV */ | |
} | |
/** | |
* @brief Get the RCC_ClkInitStruct according to the internal | |
* RCC configuration registers. | |
* @param RCC_ClkInitStruct pointer to an RCC_ClkInitTypeDef structure that | |
* contains the current clock configuration. | |
* @param pFLatency Pointer on the Flash Latency. | |
* @retval None | |
*/ | |
void HAL_RCC_GetClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t *pFLatency) | |
{ | |
/* Check the parameters */ | |
assert_param(RCC_ClkInitStruct != NULL); | |
assert_param(pFLatency != NULL); | |
/* Set all possible values for the Clock type parameter --------------------*/ | |
RCC_ClkInitStruct->ClockType = RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2; | |
/* Get the SYSCLK configuration --------------------------------------------*/ | |
RCC_ClkInitStruct->SYSCLKSource = (uint32_t)(RCC->CFGR & RCC_CFGR_SW); | |
/* Get the HCLK configuration ----------------------------------------------*/ | |
RCC_ClkInitStruct->AHBCLKDivider = (uint32_t)(RCC->CFGR & RCC_CFGR_HPRE); | |
/* Get the APB1 configuration ----------------------------------------------*/ | |
RCC_ClkInitStruct->APB1CLKDivider = (uint32_t)(RCC->CFGR & RCC_CFGR_PPRE1); | |
/* Get the APB2 configuration ----------------------------------------------*/ | |
RCC_ClkInitStruct->APB2CLKDivider = (uint32_t)((RCC->CFGR & RCC_CFGR_PPRE2) >> 3U); | |
/* Get the Flash Wait State (Latency) configuration ------------------------*/ | |
*pFLatency = (uint32_t)(FLASH->ACR & FLASH_ACR_LATENCY); | |
} | |
/** | |
* @brief This function handles the RCC CSS interrupt request. | |
* @note This API should be called under the NMI_Handler(). | |
* @retval None | |
*/ | |
void HAL_RCC_NMI_IRQHandler(void) | |
{ | |
/* Check RCC CSSF flag */ | |
if(__HAL_RCC_GET_IT(RCC_IT_CSS)) | |
{ | |
/* RCC Clock Security System interrupt user callback */ | |
HAL_RCC_CSSCallback(); | |
/* Clear RCC CSS pending bit */ | |
__HAL_RCC_CLEAR_IT(RCC_IT_CSS); | |
} | |
} | |
/** | |
* @brief RCC Clock Security System interrupt callback | |
* @retval none | |
*/ | |
__weak void HAL_RCC_CSSCallback(void) | |
{ | |
/* NOTE : This function Should not be modified, when the callback is needed, | |
the HAL_RCC_CSSCallback could be implemented in the user file | |
*/ | |
} | |
/** | |
* @} | |
*/ | |
/** | |
* @} | |
*/ | |
#endif /* HAL_RCC_MODULE_ENABLED */ | |
/** | |
* @} | |
*/ | |
/** | |
* @} | |
*/ | |
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |