| # Licensed to the Apache Software Foundation (ASF) under one |
| # or more contributor license agreements. See the NOTICE file |
| # distributed with this work for additional information |
| # regarding copyright ownership. The ASF licenses this file |
| # to you under the Apache License, Version 2.0 (the |
| # "License"); you may not use this file except in compliance |
| # with the License. You may obtain a copy of the License at |
| # |
| # http://www.apache.org/licenses/LICENSE-2.0 |
| # |
| # Unless required by applicable law or agreed to in writing, |
| # software distributed under the License is distributed on an |
| # "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY |
| # KIND, either express or implied. See the License for the |
| # specific language governing permissions and limitations |
| # under the License. |
| # |
| |
| # Package: hw/bsp/nrf52dk |
| |
| syscfg.defs: |
| BSP_NRF52: |
| description: 'Set to indicate that BSP has NRF52' |
| value: 1 |
| |
| BSP_RUUVITAG_REV_B_NUM: |
| description: > |
| Indicates exact RuuviTag hardware revision B number. This is used |
| to setup default settings for peripherals. |
| Supported values are 1-6 which corresponds to revisions B1-B6. |
| value: '6' |
| |
| SOFT_PWM: |
| description: 'Enable soft PWM' |
| value: 0 |
| |
| UARTBB_0: |
| description: 'Enable bit-banger UART 0' |
| value: 0 |
| UARTBB_0_PIN_TX: |
| description: 'TX pin for UARTBB0' |
| value: -1 |
| UARTBB_0_PIN_RX: |
| description: 'RX pin for UARTBB0' |
| value: -1 |
| |
| BME280_ONB: |
| description: 'Enable RuuviTag onboard BME280 sensor' |
| value: 0 |
| |
| LIS2DH12_ONB: |
| description: 'Enable RuuviTag onboard LIS2DH12 sensor (rev. B3 and newer)' |
| value: 0 |
| |
| syscfg.vals: |
| # Enable nRF52832 MCU |
| MCU_NRF52832: 1 |
| # Set default pins for peripherals |
| # Latest revisions have testpoints instead of dedicated UART pins, |
| # we can use them instead |
| UART_0_PIN_TX: 4 |
| UART_0_PIN_RX: 5 |
| SPI_0_MASTER_PIN_SCK: 29 |
| SPI_0_MASTER_PIN_MOSI: 25 |
| SPI_0_MASTER_PIN_MISO: 28 |
| |
| CONFIG_FCB_FLASH_AREA: FLASH_AREA_NFFS |
| REBOOT_LOG_FLASH_AREA: FLASH_AREA_REBOOT_LOG |
| NFFS_FLASH_AREA: FLASH_AREA_NFFS |
| COREDUMP_FLASH_AREA: FLASH_AREA_IMAGE_1 |
| MCU_DCDC_ENABLED: 1 |
| XTAL_32768: 1 |
| BOOT_SERIAL_DETECT_PIN: 13 # Button 1 |
| |
| syscfg.vals.'BSP_RUUVITAG_REV_B_NUM == 1': |
| # Revision B1 has dedicated pins for UART |
| UART_0_PIN_TX: 7 |
| UART_0_PIN_RX: 8 |
| |
| syscfg.vals.BLE_LP_CLOCK: |
| TIMER_0: 0 |
| TIMER_5: 1 |
| OS_CPUTIME_FREQ: 32768 |
| OS_CPUTIME_TIMER_NUM: 5 |
| BLE_XTAL_SETTLE_TIME: 1500 |
| |
| syscfg.restrictions: |
| - "!UARTBB_0 || (UARTBB_0_PIN_TX >= 0 && UARTBB_0_PIN_RX >= 0)" |
| - "!BME280_ONB || SPI_0_MASTER" |
| - "!LIS2DH12_ONB || SPI_0_MASTER" |
| - "!LIS2DH12_ONB || BSP_RUUVITAG_REV >= 3" |
