| /** |
| ****************************************************************************** |
| * @file stm32f7xx_hal_cryp.c |
| * @author MCD Application Team |
| * @brief CRYP HAL module driver. |
| * This file provides firmware functions to manage the following |
| * functionalities of the Cryptography (CRYP) peripheral: |
| * + Initialization and de-initialization functions |
| * + AES processing functions |
| * + DES processing functions |
| * + TDES processing functions |
| * + DMA callback functions |
| * + CRYP IRQ handler management |
| * + Peripheral State functions |
| * |
| @verbatim |
| ============================================================================== |
| ##### How to use this driver ##### |
| ============================================================================== |
| [..] |
| The CRYP HAL driver can be used as follows: |
| |
| (#)Initialize the CRYP low level resources by implementing the HAL_CRYP_MspInit(): |
| (##) Enable the CRYP interface clock using __HAL_RCC_CRYP_CLK_ENABLE() |
| (##) In case of using interrupts (e.g. HAL_CRYP_AESECB_Encrypt_IT()) |
| (+++) Configure the CRYP interrupt priority using HAL_NVIC_SetPriority() |
| (+++) Enable the CRYP IRQ handler using HAL_NVIC_EnableIRQ() |
| (+++) In CRYP IRQ handler, call HAL_CRYP_IRQHandler() |
| (##) In case of using DMA to control data transfer (e.g. HAL_CRYP_AESECB_Encrypt_DMA()) |
| (+++) Enable the DMAx interface clock using __DMAx_CLK_ENABLE() |
| (+++) Configure and enable two DMA streams one for managing data transfer from |
| memory to peripheral (input stream) and another stream for managing data |
| transfer from peripheral to memory (output stream) |
| (+++) Associate the initialized DMA handle to the CRYP DMA handle |
| using __HAL_LINKDMA() |
| (+++) Configure the priority and enable the NVIC for the transfer complete |
| interrupt on the two DMA Streams. The output stream should have higher |
| priority than the input stream HAL_NVIC_SetPriority() and HAL_NVIC_EnableIRQ() |
| |
| (#)Initialize the CRYP HAL using HAL_CRYP_Init(). This function configures mainly: |
| (##) The data type: 1-bit, 8-bit, 16-bit and 32-bit |
| (##) The key size: 128, 192 and 256. This parameter is relevant only for AES |
| (##) The encryption/decryption key. It's size depends on the algorithm |
| used for encryption/decryption |
| (##) The initialization vector (counter). It is not used ECB mode. |
| |
| (#)Three processing (encryption/decryption) functions are available: |
| (##) Polling mode: encryption and decryption APIs are blocking functions |
| i.e. they process the data and wait till the processing is finished, |
| e.g. HAL_CRYP_AESCBC_Encrypt() |
| (##) Interrupt mode: encryption and decryption APIs are not blocking functions |
| i.e. they process the data under interrupt, |
| e.g. HAL_CRYP_AESCBC_Encrypt_IT() |
| (##) DMA mode: encryption and decryption APIs are not blocking functions |
| i.e. the data transfer is ensured by DMA, |
| e.g. HAL_CRYP_AESCBC_Encrypt_DMA() |
| |
| (#)When the processing function is called at first time after HAL_CRYP_Init() |
| the CRYP peripheral is initialized and processes the buffer in input. |
| At second call, the processing function performs an append of the already |
| processed buffer. |
| When a new data block is to be processed, call HAL_CRYP_Init() then the |
| processing function. |
| |
| (#)Call HAL_CRYP_DeInit() to deinitialize the CRYP peripheral. |
| |
| @endverbatim |
| ****************************************************************************** |
| * @attention |
| * |
| * <h2><center>© COPYRIGHT(c) 2017 STMicroelectronics</center></h2> |
| * |
| * Redistribution and use in source and binary forms, with or without modification, |
| * are permitted provided that the following conditions are met: |
| * 1. Redistributions of source code must retain the above copyright notice, |
| * this list of conditions and the following disclaimer. |
| * 2. Redistributions in binary form must reproduce the above copyright notice, |
| * this list of conditions and the following disclaimer in the documentation |
| * and/or other materials provided with the distribution. |
| * 3. Neither the name of STMicroelectronics nor the names of its contributors |
| * may be used to endorse or promote products derived from this software |
| * without specific prior written permission. |
| * |
| * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" |
| * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE |
| * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE |
| * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE |
| * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL |
| * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR |
| * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER |
| * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, |
| * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE |
| * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. |
| * |
| ****************************************************************************** |
| */ |
| |
| /* Includes ------------------------------------------------------------------*/ |
| #include "stm32f7xx_hal.h" |
| |
| #ifdef HAL_CRYP_MODULE_ENABLED |
| |
| #if defined (CRYP) |
| |
| /** @addtogroup STM32F7xx_HAL_Driver |
| * @{ |
| */ |
| /** @defgroup CRYP CRYP |
| * @brief CRYP HAL module driver. |
| * @{ |
| */ |
| |
| /* Private typedef -----------------------------------------------------------*/ |
| /* Private define ------------------------------------------------------------*/ |
| /** @addtogroup CRYP_Private_define |
| * @{ |
| */ |
| #define CRYP_TIMEOUT_VALUE 1 |
| /** |
| * @} |
| */ |
| |
| /* Private macro -------------------------------------------------------------*/ |
| /* Private variables ---------------------------------------------------------*/ |
| /* Private function prototypes -----------------------------------------------*/ |
| /** @addtogroup CRYP_Private_Functions_prototypes |
| * @{ |
| */ |
| static void CRYP_SetInitVector(CRYP_HandleTypeDef *hcryp, uint8_t *InitVector, uint32_t IVSize); |
| static void CRYP_SetKey(CRYP_HandleTypeDef *hcryp, uint8_t *Key, uint32_t KeySize); |
| static HAL_StatusTypeDef CRYP_ProcessData(CRYP_HandleTypeDef *hcryp, uint8_t* Input, uint16_t Ilength, uint8_t* Output, uint32_t Timeout); |
| static HAL_StatusTypeDef CRYP_ProcessData2Words(CRYP_HandleTypeDef *hcryp, uint8_t* Input, uint16_t Ilength, uint8_t* Output, uint32_t Timeout); |
| static void CRYP_DMAInCplt(DMA_HandleTypeDef *hdma); |
| static void CRYP_DMAOutCplt(DMA_HandleTypeDef *hdma); |
| static void CRYP_DMAError(DMA_HandleTypeDef *hdma); |
| static void CRYP_SetDMAConfig(CRYP_HandleTypeDef *hcryp, uint32_t inputaddr, uint16_t Size, uint32_t outputaddr); |
| static void CRYP_SetTDESECBMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction); |
| static void CRYP_SetTDESCBCMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction); |
| static void CRYP_SetDESECBMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction); |
| static void CRYP_SetDESCBCMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction); |
| /** |
| * @} |
| */ |
| /* Private functions ---------------------------------------------------------*/ |
| |
| /** @addtogroup CRYP_Private_Functions |
| * @{ |
| */ |
| |
| /** |
| * @brief DMA CRYP Input Data process complete callback. |
| * @param hdma DMA handle |
| * @retval None |
| */ |
| static void CRYP_DMAInCplt(DMA_HandleTypeDef *hdma) |
| { |
| CRYP_HandleTypeDef* hcryp = (CRYP_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent; |
| |
| /* Disable the DMA transfer for input FIFO request by resetting the DIEN bit |
| in the DMACR register */ |
| hcryp->Instance->DMACR &= (uint32_t)(~CRYP_DMACR_DIEN); |
| |
| /* Call input data transfer complete callback */ |
| HAL_CRYP_InCpltCallback(hcryp); |
| } |
| |
| /** |
| * @brief DMA CRYP Output Data process complete callback. |
| * @param hdma DMA handle |
| * @retval None |
| */ |
| static void CRYP_DMAOutCplt(DMA_HandleTypeDef *hdma) |
| { |
| CRYP_HandleTypeDef* hcryp = (CRYP_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent; |
| |
| /* Disable the DMA transfer for output FIFO request by resetting the DOEN bit |
| in the DMACR register */ |
| hcryp->Instance->DMACR &= (uint32_t)(~CRYP_DMACR_DOEN); |
| |
| /* Disable CRYP */ |
| __HAL_CRYP_DISABLE(hcryp); |
| |
| /* Change the CRYP state to ready */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| |
| /* Call output data transfer complete callback */ |
| HAL_CRYP_OutCpltCallback(hcryp); |
| } |
| |
| /** |
| * @brief DMA CRYP communication error callback. |
| * @param hdma DMA handle |
| * @retval None |
| */ |
| static void CRYP_DMAError(DMA_HandleTypeDef *hdma) |
| { |
| CRYP_HandleTypeDef* hcryp = (CRYP_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent; |
| hcryp->State= HAL_CRYP_STATE_READY; |
| HAL_CRYP_ErrorCallback(hcryp); |
| } |
| |
| /** |
| * @brief Writes the Key in Key registers. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param Key Pointer to Key buffer |
| * @param KeySize Size of Key |
| * @retval None |
| */ |
| static void CRYP_SetKey(CRYP_HandleTypeDef *hcryp, uint8_t *Key, uint32_t KeySize) |
| { |
| uint32_t keyaddr = (uint32_t)Key; |
| |
| switch(KeySize) |
| { |
| case CRYP_KEYSIZE_256B: |
| /* Key Initialisation */ |
| hcryp->Instance->K0LR = __REV(*(uint32_t*)(keyaddr)); |
| keyaddr+=4; |
| hcryp->Instance->K0RR = __REV(*(uint32_t*)(keyaddr)); |
| keyaddr+=4; |
| hcryp->Instance->K1LR = __REV(*(uint32_t*)(keyaddr)); |
| keyaddr+=4; |
| hcryp->Instance->K1RR = __REV(*(uint32_t*)(keyaddr)); |
| keyaddr+=4; |
| hcryp->Instance->K2LR = __REV(*(uint32_t*)(keyaddr)); |
| keyaddr+=4; |
| hcryp->Instance->K2RR = __REV(*(uint32_t*)(keyaddr)); |
| keyaddr+=4; |
| hcryp->Instance->K3LR = __REV(*(uint32_t*)(keyaddr)); |
| keyaddr+=4; |
| hcryp->Instance->K3RR = __REV(*(uint32_t*)(keyaddr)); |
| break; |
| case CRYP_KEYSIZE_192B: |
| hcryp->Instance->K1LR = __REV(*(uint32_t*)(keyaddr)); |
| keyaddr+=4; |
| hcryp->Instance->K1RR = __REV(*(uint32_t*)(keyaddr)); |
| keyaddr+=4; |
| hcryp->Instance->K2LR = __REV(*(uint32_t*)(keyaddr)); |
| keyaddr+=4; |
| hcryp->Instance->K2RR = __REV(*(uint32_t*)(keyaddr)); |
| keyaddr+=4; |
| hcryp->Instance->K3LR = __REV(*(uint32_t*)(keyaddr)); |
| keyaddr+=4; |
| hcryp->Instance->K3RR = __REV(*(uint32_t*)(keyaddr)); |
| break; |
| case CRYP_KEYSIZE_128B: |
| hcryp->Instance->K2LR = __REV(*(uint32_t*)(keyaddr)); |
| keyaddr+=4; |
| hcryp->Instance->K2RR = __REV(*(uint32_t*)(keyaddr)); |
| keyaddr+=4; |
| hcryp->Instance->K3LR = __REV(*(uint32_t*)(keyaddr)); |
| keyaddr+=4; |
| hcryp->Instance->K3RR = __REV(*(uint32_t*)(keyaddr)); |
| break; |
| default: |
| break; |
| } |
| } |
| |
| /** |
| * @brief Writes the InitVector/InitCounter in IV registers. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param InitVector Pointer to InitVector/InitCounter buffer |
| * @param IVSize Size of the InitVector/InitCounter |
| * @retval None |
| */ |
| static void CRYP_SetInitVector(CRYP_HandleTypeDef *hcryp, uint8_t *InitVector, uint32_t IVSize) |
| { |
| uint32_t ivaddr = (uint32_t)InitVector; |
| |
| switch(IVSize) |
| { |
| case CRYP_KEYSIZE_128B: |
| hcryp->Instance->IV0LR = __REV(*(uint32_t*)(ivaddr)); |
| ivaddr+=4; |
| hcryp->Instance->IV0RR = __REV(*(uint32_t*)(ivaddr)); |
| ivaddr+=4; |
| hcryp->Instance->IV1LR = __REV(*(uint32_t*)(ivaddr)); |
| ivaddr+=4; |
| hcryp->Instance->IV1RR = __REV(*(uint32_t*)(ivaddr)); |
| break; |
| /* Whatever key size 192 or 256, Init vector is written in IV0LR and IV0RR */ |
| case CRYP_KEYSIZE_192B: |
| hcryp->Instance->IV0LR = __REV(*(uint32_t*)(ivaddr)); |
| ivaddr+=4; |
| hcryp->Instance->IV0RR = __REV(*(uint32_t*)(ivaddr)); |
| break; |
| case CRYP_KEYSIZE_256B: |
| hcryp->Instance->IV0LR = __REV(*(uint32_t*)(ivaddr)); |
| ivaddr+=4; |
| hcryp->Instance->IV0RR = __REV(*(uint32_t*)(ivaddr)); |
| break; |
| default: |
| break; |
| } |
| } |
| |
| /** |
| * @brief Process Data: Writes Input data in polling mode and read the output data |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param Input Pointer to the Input buffer |
| * @param Ilength Length of the Input buffer, must be a multiple of 16. |
| * @param Output Pointer to the returned buffer |
| * @param Timeout Timeout value |
| * @retval None |
| */ |
| static HAL_StatusTypeDef CRYP_ProcessData(CRYP_HandleTypeDef *hcryp, uint8_t* Input, uint16_t Ilength, uint8_t* Output, uint32_t Timeout) |
| { |
| uint32_t tickstart = 0; |
| |
| uint32_t i = 0; |
| uint32_t inputaddr = (uint32_t)Input; |
| uint32_t outputaddr = (uint32_t)Output; |
| |
| for(i=0; (i < Ilength); i+=16) |
| { |
| /* Write the Input block in the IN FIFO */ |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| |
| /* Get tick */ |
| tickstart = HAL_GetTick(); |
| |
| while(HAL_IS_BIT_CLR(hcryp->Instance->SR, CRYP_FLAG_OFNE)) |
| { |
| /* Check for the Timeout */ |
| if(Timeout != HAL_MAX_DELAY) |
| { |
| if((Timeout == 0)||((HAL_GetTick() - tickstart ) > Timeout)) |
| { |
| /* Change state */ |
| hcryp->State = HAL_CRYP_STATE_TIMEOUT; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| return HAL_TIMEOUT; |
| } |
| } |
| } |
| /* Read the Output block from the Output FIFO */ |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| } |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Process Data: Write Input data in polling mode. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param Input Pointer to the Input buffer |
| * @param Ilength Length of the Input buffer, must be a multiple of 8 |
| * @param Output Pointer to the returned buffer |
| * @param Timeout Specify Timeout value |
| * @retval None |
| */ |
| static HAL_StatusTypeDef CRYP_ProcessData2Words(CRYP_HandleTypeDef *hcryp, uint8_t* Input, uint16_t Ilength, uint8_t* Output, uint32_t Timeout) |
| { |
| uint32_t tickstart = 0; |
| |
| uint32_t i = 0; |
| uint32_t inputaddr = (uint32_t)Input; |
| uint32_t outputaddr = (uint32_t)Output; |
| |
| for(i=0; (i < Ilength); i+=8) |
| { |
| /* Write the Input block in the IN FIFO */ |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| |
| /* Get tick */ |
| tickstart = HAL_GetTick(); |
| |
| while(HAL_IS_BIT_CLR(hcryp->Instance->SR, CRYP_FLAG_OFNE)) |
| { |
| /* Check for the Timeout */ |
| if(Timeout != HAL_MAX_DELAY) |
| { |
| if((Timeout == 0)||((HAL_GetTick() - tickstart ) > Timeout)) |
| { |
| /* Change state */ |
| hcryp->State = HAL_CRYP_STATE_TIMEOUT; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| return HAL_TIMEOUT; |
| } |
| } |
| } |
| /* Read the Output block from the Output FIFO */ |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| } |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Set the DMA configuration and start the DMA transfer |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param inputaddr address of the Input buffer |
| * @param Size Size of the Input buffer, must be a multiple of 16. |
| * @param outputaddr address of the Output buffer |
| * @retval None |
| */ |
| static void CRYP_SetDMAConfig(CRYP_HandleTypeDef *hcryp, uint32_t inputaddr, uint16_t Size, uint32_t outputaddr) |
| { |
| /* Set the CRYP DMA transfer complete callback */ |
| hcryp->hdmain->XferCpltCallback = CRYP_DMAInCplt; |
| /* Set the DMA error callback */ |
| hcryp->hdmain->XferErrorCallback = CRYP_DMAError; |
| |
| /* Set the CRYP DMA transfer complete callback */ |
| hcryp->hdmaout->XferCpltCallback = CRYP_DMAOutCplt; |
| /* Set the DMA error callback */ |
| hcryp->hdmaout->XferErrorCallback = CRYP_DMAError; |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Enable the DMA In DMA Stream */ |
| HAL_DMA_Start_IT(hcryp->hdmain, inputaddr, (uint32_t)&hcryp->Instance->DR, Size/4); |
| |
| /* Enable In DMA request */ |
| hcryp->Instance->DMACR = (CRYP_DMACR_DIEN); |
| |
| /* Enable the DMA Out DMA Stream */ |
| HAL_DMA_Start_IT(hcryp->hdmaout, (uint32_t)&hcryp->Instance->DOUT, outputaddr, Size/4); |
| |
| /* Enable Out DMA request */ |
| hcryp->Instance->DMACR |= CRYP_DMACR_DOEN; |
| |
| } |
| |
| /** |
| * @brief Sets the CRYP peripheral in DES ECB mode. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param Direction Encryption or decryption |
| * @retval None |
| */ |
| static void CRYP_SetDESECBMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction) |
| { |
| /* Check if initialization phase has already been performed */ |
| if(hcryp->Phase == HAL_CRYP_PHASE_READY) |
| { |
| /* Set the CRYP peripheral in AES ECB mode */ |
| __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_DES_ECB | Direction); |
| |
| /* Set the key */ |
| hcryp->Instance->K1LR = __REV(*(uint32_t*)(hcryp->Init.pKey)); |
| hcryp->Instance->K1RR = __REV(*(uint32_t*)(hcryp->Init.pKey+4)); |
| |
| /* Flush FIFO */ |
| __HAL_CRYP_FIFO_FLUSH(hcryp); |
| |
| /* Set the phase */ |
| hcryp->Phase = HAL_CRYP_PHASE_PROCESS; |
| } |
| } |
| |
| /** |
| * @brief Sets the CRYP peripheral in DES CBC mode. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param Direction Encryption or decryption |
| * @retval None |
| */ |
| static void CRYP_SetDESCBCMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction) |
| { |
| /* Check if initialization phase has already been performed */ |
| if(hcryp->Phase == HAL_CRYP_PHASE_READY) |
| { |
| /* Set the CRYP peripheral in AES ECB mode */ |
| __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_DES_CBC | Direction); |
| |
| /* Set the key */ |
| hcryp->Instance->K1LR = __REV(*(uint32_t*)(hcryp->Init.pKey)); |
| hcryp->Instance->K1RR = __REV(*(uint32_t*)(hcryp->Init.pKey+4)); |
| |
| /* Set the Initialization Vector */ |
| CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_256B); |
| |
| /* Flush FIFO */ |
| __HAL_CRYP_FIFO_FLUSH(hcryp); |
| |
| /* Set the phase */ |
| hcryp->Phase = HAL_CRYP_PHASE_PROCESS; |
| } |
| } |
| |
| /** |
| * @brief Sets the CRYP peripheral in TDES ECB mode. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param Direction Encryption or decryption |
| * @retval None |
| */ |
| static void CRYP_SetTDESECBMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction) |
| { |
| /* Check if initialization phase has already been performed */ |
| if(hcryp->Phase == HAL_CRYP_PHASE_READY) |
| { |
| /* Set the CRYP peripheral in AES ECB mode */ |
| __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_TDES_ECB | Direction); |
| |
| /* Set the key */ |
| CRYP_SetKey(hcryp, hcryp->Init.pKey, CRYP_KEYSIZE_192B); |
| |
| /* Flush FIFO */ |
| __HAL_CRYP_FIFO_FLUSH(hcryp); |
| |
| /* Set the phase */ |
| hcryp->Phase = HAL_CRYP_PHASE_PROCESS; |
| } |
| } |
| |
| /** |
| * @brief Sets the CRYP peripheral in TDES CBC mode |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param Direction Encryption or decryption |
| * @retval None |
| */ |
| static void CRYP_SetTDESCBCMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction) |
| { |
| /* Check if initialization phase has already been performed */ |
| if(hcryp->Phase == HAL_CRYP_PHASE_READY) |
| { |
| /* Set the CRYP peripheral in AES CBC mode */ |
| __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_TDES_CBC | Direction); |
| |
| /* Set the key */ |
| CRYP_SetKey(hcryp, hcryp->Init.pKey, CRYP_KEYSIZE_192B); |
| |
| /* Set the Initialization Vector */ |
| CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_256B); |
| |
| /* Flush FIFO */ |
| __HAL_CRYP_FIFO_FLUSH(hcryp); |
| |
| /* Set the phase */ |
| hcryp->Phase = HAL_CRYP_PHASE_PROCESS; |
| } |
| } |
| |
| /** |
| * @} |
| */ |
| |
| /* Exported functions --------------------------------------------------------*/ |
| /** @addtogroup CRYP_Exported_Functions |
| * @{ |
| */ |
| |
| /** @defgroup CRYP_Exported_Functions_Group1 Initialization and de-initialization functions |
| * @brief Initialization and Configuration functions. |
| * |
| @verbatim |
| ============================================================================== |
| ##### Initialization and de-initialization functions ##### |
| ============================================================================== |
| [..] This section provides functions allowing to: |
| (+) Initialize the CRYP according to the specified parameters |
| in the CRYP_InitTypeDef and creates the associated handle |
| (+) DeInitialize the CRYP peripheral |
| (+) Initialize the CRYP MSP |
| (+) DeInitialize CRYP MSP |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief Initializes the CRYP according to the specified |
| * parameters in the CRYP_InitTypeDef and creates the associated handle. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_Init(CRYP_HandleTypeDef *hcryp) |
| { |
| /* Check the CRYP handle allocation */ |
| if(hcryp == NULL) |
| { |
| return HAL_ERROR; |
| } |
| |
| /* Check the parameters */ |
| assert_param(IS_CRYP_KEYSIZE(hcryp->Init.KeySize)); |
| assert_param(IS_CRYP_DATATYPE(hcryp->Init.DataType)); |
| |
| if(hcryp->State == HAL_CRYP_STATE_RESET) |
| { |
| /* Allocate lock resource and initialize it */ |
| hcryp->Lock = HAL_UNLOCKED; |
| /* Init the low level hardware */ |
| HAL_CRYP_MspInit(hcryp); |
| } |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Set the key size and data type*/ |
| CRYP->CR = (uint32_t) (hcryp->Init.KeySize | hcryp->Init.DataType); |
| |
| /* Reset CrypInCount and CrypOutCount */ |
| hcryp->CrypInCount = 0; |
| hcryp->CrypOutCount = 0; |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| |
| /* Set the default CRYP phase */ |
| hcryp->Phase = HAL_CRYP_PHASE_READY; |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief DeInitializes the CRYP peripheral. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_DeInit(CRYP_HandleTypeDef *hcryp) |
| { |
| /* Check the CRYP handle allocation */ |
| if(hcryp == NULL) |
| { |
| return HAL_ERROR; |
| } |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Set the default CRYP phase */ |
| hcryp->Phase = HAL_CRYP_PHASE_READY; |
| |
| /* Reset CrypInCount and CrypOutCount */ |
| hcryp->CrypInCount = 0; |
| hcryp->CrypOutCount = 0; |
| |
| /* Disable the CRYP Peripheral Clock */ |
| __HAL_CRYP_DISABLE(hcryp); |
| |
| /* DeInit the low level hardware: CLOCK, NVIC.*/ |
| HAL_CRYP_MspDeInit(hcryp); |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_RESET; |
| |
| /* Release Lock */ |
| __HAL_UNLOCK(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the CRYP MSP. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @retval None |
| */ |
| __weak void HAL_CRYP_MspInit(CRYP_HandleTypeDef *hcryp) |
| { |
| /* Prevent unused argument(s) compilation warning */ |
| UNUSED(hcryp); |
| |
| /* NOTE : This function Should not be modified, when the callback is needed, |
| the HAL_CRYP_MspInit could be implemented in the user file |
| */ |
| } |
| |
| /** |
| * @brief DeInitializes CRYP MSP. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @retval None |
| */ |
| __weak void HAL_CRYP_MspDeInit(CRYP_HandleTypeDef *hcryp) |
| { |
| /* Prevent unused argument(s) compilation warning */ |
| UNUSED(hcryp); |
| |
| /* NOTE : This function Should not be modified, when the callback is needed, |
| the HAL_CRYP_MspDeInit could be implemented in the user file |
| */ |
| } |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup CRYP_Exported_Functions_Group2 AES processing functions |
| * @brief processing functions. |
| * |
| @verbatim |
| ============================================================================== |
| ##### AES processing functions ##### |
| ============================================================================== |
| [..] This section provides functions allowing to: |
| (+) Encrypt plaintext using AES-128/192/256 using chaining modes |
| (+) Decrypt cyphertext using AES-128/192/256 using chaining modes |
| [..] Three processing functions are available: |
| (+) Polling mode |
| (+) Interrupt mode |
| (+) DMA mode |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief Initializes the CRYP peripheral in AES ECB encryption mode |
| * then encrypt pPlainData. The cypher data are available in pCypherData |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 16. |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Timeout Specify Timeout value |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESECB_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Check if initialization phase has already been performed */ |
| if(hcryp->Phase == HAL_CRYP_PHASE_READY) |
| { |
| /* Set the key */ |
| CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); |
| |
| /* Set the CRYP peripheral in AES ECB mode */ |
| __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_ECB); |
| |
| /* Flush FIFO */ |
| __HAL_CRYP_FIFO_FLUSH(hcryp); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Set the phase */ |
| hcryp->Phase = HAL_CRYP_PHASE_PROCESS; |
| } |
| |
| /* Write Plain Data and Get Cypher Data */ |
| if(CRYP_ProcessData(hcryp, pPlainData, Size, pCypherData, Timeout) != HAL_OK) |
| { |
| return HAL_TIMEOUT; |
| } |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in AES CBC encryption mode |
| * then encrypt pPlainData. The cypher data are available in pCypherData |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 16. |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Timeout Specify Timeout value |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESCBC_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Check if initialization phase has already been performed */ |
| if(hcryp->Phase == HAL_CRYP_PHASE_READY) |
| { |
| /* Set the key */ |
| CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); |
| |
| /* Set the CRYP peripheral in AES ECB mode */ |
| __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CBC); |
| |
| /* Set the Initialization Vector */ |
| CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B); |
| |
| /* Flush FIFO */ |
| __HAL_CRYP_FIFO_FLUSH(hcryp); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Set the phase */ |
| hcryp->Phase = HAL_CRYP_PHASE_PROCESS; |
| } |
| |
| /* Write Plain Data and Get Cypher Data */ |
| if(CRYP_ProcessData(hcryp,pPlainData, Size, pCypherData, Timeout) != HAL_OK) |
| { |
| return HAL_TIMEOUT; |
| } |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in AES CTR encryption mode |
| * then encrypt pPlainData. The cypher data are available in pCypherData |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 16. |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Timeout Specify Timeout value |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESCTR_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Check if initialization phase has already been performed */ |
| if(hcryp->Phase == HAL_CRYP_PHASE_READY) |
| { |
| /* Set the key */ |
| CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); |
| |
| /* Set the CRYP peripheral in AES ECB mode */ |
| __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CTR); |
| |
| /* Set the Initialization Vector */ |
| CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B); |
| |
| /* Flush FIFO */ |
| __HAL_CRYP_FIFO_FLUSH(hcryp); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Set the phase */ |
| hcryp->Phase = HAL_CRYP_PHASE_PROCESS; |
| } |
| |
| /* Write Plain Data and Get Cypher Data */ |
| if(CRYP_ProcessData(hcryp, pPlainData, Size, pCypherData, Timeout) != HAL_OK) |
| { |
| return HAL_TIMEOUT; |
| } |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| |
| |
| /** |
| * @brief Initializes the CRYP peripheral in AES ECB decryption mode |
| * then decrypted pCypherData. The cypher data are available in pPlainData |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 16. |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Timeout Specify Timeout value |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESECB_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout) |
| { |
| uint32_t tickstart = 0; |
| |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Check if initialization phase has already been performed */ |
| if(hcryp->Phase == HAL_CRYP_PHASE_READY) |
| { |
| /* Set the key */ |
| CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); |
| |
| /* Set the CRYP peripheral in AES Key mode */ |
| __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_KEY | CRYP_CR_ALGODIR); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Get tick */ |
| tickstart = HAL_GetTick(); |
| |
| while(HAL_IS_BIT_SET(hcryp->Instance->SR, CRYP_FLAG_BUSY)) |
| { |
| /* Check for the Timeout */ |
| if(Timeout != HAL_MAX_DELAY) |
| { |
| if((Timeout == 0)||((HAL_GetTick() - tickstart ) > Timeout)) |
| { |
| /* Change state */ |
| hcryp->State = HAL_CRYP_STATE_TIMEOUT; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| return HAL_TIMEOUT; |
| } |
| } |
| } |
| |
| /* Disable CRYP */ |
| __HAL_CRYP_DISABLE(hcryp); |
| |
| /* Reset the ALGOMODE bits*/ |
| CRYP->CR &= (uint32_t)(~CRYP_CR_ALGOMODE); |
| |
| /* Set the CRYP peripheral in AES ECB decryption mode */ |
| __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_ECB | CRYP_CR_ALGODIR); |
| /* Flush FIFO */ |
| __HAL_CRYP_FIFO_FLUSH(hcryp); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Set the phase */ |
| hcryp->Phase = HAL_CRYP_PHASE_PROCESS; |
| } |
| |
| /* Write Plain Data and Get Cypher Data */ |
| if(CRYP_ProcessData(hcryp, pCypherData, Size, pPlainData, Timeout) != HAL_OK) |
| { |
| return HAL_TIMEOUT; |
| } |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in AES ECB decryption mode |
| * then decrypted pCypherData. The cypher data are available in pPlainData |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 16. |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Timeout Specify Timeout value |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESCBC_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout) |
| { |
| uint32_t tickstart = 0; |
| |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Check if initialization phase has already been performed */ |
| if(hcryp->Phase == HAL_CRYP_PHASE_READY) |
| { |
| /* Set the key */ |
| CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); |
| |
| /* Set the CRYP peripheral in AES Key mode */ |
| __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_KEY | CRYP_CR_ALGODIR); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Get tick */ |
| tickstart = HAL_GetTick(); |
| |
| while(HAL_IS_BIT_SET(hcryp->Instance->SR, CRYP_FLAG_BUSY)) |
| { |
| /* Check for the Timeout */ |
| if(Timeout != HAL_MAX_DELAY) |
| { |
| if((Timeout == 0)||((HAL_GetTick() - tickstart ) > Timeout)) |
| { |
| /* Change state */ |
| hcryp->State = HAL_CRYP_STATE_TIMEOUT; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| return HAL_TIMEOUT; |
| } |
| } |
| } |
| |
| /* Reset the ALGOMODE bits*/ |
| CRYP->CR &= (uint32_t)(~CRYP_CR_ALGOMODE); |
| |
| /* Set the CRYP peripheral in AES CBC decryption mode */ |
| __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CBC | CRYP_CR_ALGODIR); |
| |
| /* Set the Initialization Vector */ |
| CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B); |
| |
| /* Flush FIFO */ |
| __HAL_CRYP_FIFO_FLUSH(hcryp); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Set the phase */ |
| hcryp->Phase = HAL_CRYP_PHASE_PROCESS; |
| } |
| |
| /* Write Plain Data and Get Cypher Data */ |
| if(CRYP_ProcessData(hcryp, pCypherData, Size, pPlainData, Timeout) != HAL_OK) |
| { |
| return HAL_TIMEOUT; |
| } |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in AES CTR decryption mode |
| * then decrypted pCypherData. The cypher data are available in pPlainData |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 16. |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Timeout Specify Timeout value |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESCTR_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| /* Check if initialization phase has already been performed */ |
| if(hcryp->Phase == HAL_CRYP_PHASE_READY) |
| { |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Set the key */ |
| CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); |
| |
| /* Set the CRYP peripheral in AES CTR mode */ |
| __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CTR | CRYP_CR_ALGODIR); |
| |
| /* Set the Initialization Vector */ |
| CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B); |
| |
| /* Flush FIFO */ |
| __HAL_CRYP_FIFO_FLUSH(hcryp); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Set the phase */ |
| hcryp->Phase = HAL_CRYP_PHASE_PROCESS; |
| } |
| |
| /* Write Plain Data and Get Cypher Data */ |
| if(CRYP_ProcessData(hcryp, pCypherData, Size, pPlainData, Timeout) != HAL_OK) |
| { |
| return HAL_TIMEOUT; |
| } |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in AES ECB encryption mode using Interrupt. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 16 bytes |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESECB_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) |
| { |
| uint32_t inputaddr; |
| uint32_t outputaddr; |
| |
| if(hcryp->State == HAL_CRYP_STATE_READY) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| hcryp->CrypInCount = Size; |
| hcryp->pCrypInBuffPtr = pPlainData; |
| hcryp->pCrypOutBuffPtr = pCypherData; |
| hcryp->CrypOutCount = Size; |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Check if initialization phase has already been performed */ |
| if(hcryp->Phase == HAL_CRYP_PHASE_READY) |
| { |
| /* Set the key */ |
| CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); |
| |
| /* Set the CRYP peripheral in AES ECB mode */ |
| __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_ECB); |
| |
| /* Flush FIFO */ |
| __HAL_CRYP_FIFO_FLUSH(hcryp); |
| |
| /* Set the phase */ |
| hcryp->Phase = HAL_CRYP_PHASE_PROCESS; |
| } |
| |
| /* Enable Interrupts */ |
| __HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI)) |
| { |
| inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; |
| /* Write the Input block in the IN FIFO */ |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| hcryp->pCrypInBuffPtr += 16; |
| hcryp->CrypInCount -= 16; |
| if(hcryp->CrypInCount == 0) |
| { |
| __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI); |
| /* Call the Input data transfer complete callback */ |
| HAL_CRYP_InCpltCallback(hcryp); |
| } |
| } |
| else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI)) |
| { |
| outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; |
| /* Read the Output block from the Output FIFO */ |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| hcryp->pCrypOutBuffPtr += 16; |
| hcryp->CrypOutCount -= 16; |
| if(hcryp->CrypOutCount == 0) |
| { |
| __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI); |
| /* Process Locked */ |
| __HAL_UNLOCK(hcryp); |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| /* Call Input transfer complete callback */ |
| HAL_CRYP_OutCpltCallback(hcryp); |
| } |
| } |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in AES CBC encryption mode using Interrupt. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 16 bytes |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESCBC_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) |
| { |
| uint32_t inputaddr; |
| uint32_t outputaddr; |
| |
| if(hcryp->State == HAL_CRYP_STATE_READY) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| hcryp->CrypInCount = Size; |
| hcryp->pCrypInBuffPtr = pPlainData; |
| hcryp->pCrypOutBuffPtr = pCypherData; |
| hcryp->CrypOutCount = Size; |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Check if initialization phase has already been performed */ |
| if(hcryp->Phase == HAL_CRYP_PHASE_READY) |
| { |
| /* Set the key */ |
| CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); |
| |
| /* Set the CRYP peripheral in AES CBC mode */ |
| __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CBC); |
| |
| /* Set the Initialization Vector */ |
| CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B); |
| |
| /* Flush FIFO */ |
| __HAL_CRYP_FIFO_FLUSH(hcryp); |
| |
| /* Set the phase */ |
| hcryp->Phase = HAL_CRYP_PHASE_PROCESS; |
| } |
| /* Enable Interrupts */ |
| __HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI)) |
| { |
| inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; |
| /* Write the Input block in the IN FIFO */ |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| hcryp->pCrypInBuffPtr += 16; |
| hcryp->CrypInCount -= 16; |
| if(hcryp->CrypInCount == 0) |
| { |
| __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI); |
| /* Call the Input data transfer complete callback */ |
| HAL_CRYP_InCpltCallback(hcryp); |
| } |
| } |
| else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI)) |
| { |
| outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; |
| /* Read the Output block from the Output FIFO */ |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| hcryp->pCrypOutBuffPtr += 16; |
| hcryp->CrypOutCount -= 16; |
| if(hcryp->CrypOutCount == 0) |
| { |
| __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI); |
| /* Process Locked */ |
| __HAL_UNLOCK(hcryp); |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| /* Call Input transfer complete callback */ |
| HAL_CRYP_OutCpltCallback(hcryp); |
| } |
| } |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in AES CTR encryption mode using Interrupt. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 16 bytes |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESCTR_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) |
| { |
| uint32_t inputaddr; |
| uint32_t outputaddr; |
| |
| if(hcryp->State == HAL_CRYP_STATE_READY) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| hcryp->CrypInCount = Size; |
| hcryp->pCrypInBuffPtr = pPlainData; |
| hcryp->pCrypOutBuffPtr = pCypherData; |
| hcryp->CrypOutCount = Size; |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Check if initialization phase has already been performed */ |
| if(hcryp->Phase == HAL_CRYP_PHASE_READY) |
| { |
| /* Set the key */ |
| CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); |
| |
| /* Set the CRYP peripheral in AES CTR mode */ |
| __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CTR); |
| |
| /* Set the Initialization Vector */ |
| CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B); |
| |
| /* Flush FIFO */ |
| __HAL_CRYP_FIFO_FLUSH(hcryp); |
| |
| /* Set the phase */ |
| hcryp->Phase = HAL_CRYP_PHASE_PROCESS; |
| } |
| /* Enable Interrupts */ |
| __HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI)) |
| { |
| inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; |
| /* Write the Input block in the IN FIFO */ |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| hcryp->pCrypInBuffPtr += 16; |
| hcryp->CrypInCount -= 16; |
| if(hcryp->CrypInCount == 0) |
| { |
| __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI); |
| /* Call the Input data transfer complete callback */ |
| HAL_CRYP_InCpltCallback(hcryp); |
| } |
| } |
| else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI)) |
| { |
| outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; |
| /* Read the Output block from the Output FIFO */ |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| hcryp->pCrypOutBuffPtr += 16; |
| hcryp->CrypOutCount -= 16; |
| if(hcryp->CrypOutCount == 0) |
| { |
| __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI); |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| /* Call Input transfer complete callback */ |
| HAL_CRYP_OutCpltCallback(hcryp); |
| } |
| } |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| |
| /** |
| * @brief Initializes the CRYP peripheral in AES ECB decryption mode using Interrupt. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 16. |
| * @param pPlainData Pointer to the plaintext buffer |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESECB_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) |
| { |
| uint32_t tickstart = 0; |
| |
| uint32_t inputaddr; |
| uint32_t outputaddr; |
| |
| if(hcryp->State == HAL_CRYP_STATE_READY) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| hcryp->CrypInCount = Size; |
| hcryp->pCrypInBuffPtr = pCypherData; |
| hcryp->pCrypOutBuffPtr = pPlainData; |
| hcryp->CrypOutCount = Size; |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Check if initialization phase has already been performed */ |
| if(hcryp->Phase == HAL_CRYP_PHASE_READY) |
| { |
| /* Set the key */ |
| CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); |
| |
| /* Set the CRYP peripheral in AES Key mode */ |
| __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_KEY | CRYP_CR_ALGODIR); |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Get tick */ |
| tickstart = HAL_GetTick(); |
| |
| while(HAL_IS_BIT_SET(hcryp->Instance->SR, CRYP_FLAG_BUSY)) |
| { |
| /* Check for the Timeout */ |
| if((HAL_GetTick() - tickstart ) > CRYP_TIMEOUT_VALUE) |
| { |
| /* Change state */ |
| hcryp->State = HAL_CRYP_STATE_TIMEOUT; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| return HAL_TIMEOUT; |
| } |
| } |
| |
| /* Reset the ALGOMODE bits*/ |
| CRYP->CR &= (uint32_t)(~CRYP_CR_ALGOMODE); |
| |
| /* Set the CRYP peripheral in AES ECB decryption mode */ |
| __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_ECB | CRYP_CR_ALGODIR); |
| |
| /* Flush FIFO */ |
| __HAL_CRYP_FIFO_FLUSH(hcryp); |
| |
| /* Set the phase */ |
| hcryp->Phase = HAL_CRYP_PHASE_PROCESS; |
| } |
| |
| /* Enable Interrupts */ |
| __HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI)) |
| { |
| inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; |
| /* Write the Input block in the IN FIFO */ |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| hcryp->pCrypInBuffPtr += 16; |
| hcryp->CrypInCount -= 16; |
| if(hcryp->CrypInCount == 0) |
| { |
| __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI); |
| /* Call the Input data transfer complete callback */ |
| HAL_CRYP_InCpltCallback(hcryp); |
| } |
| } |
| else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI)) |
| { |
| outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; |
| /* Read the Output block from the Output FIFO */ |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| hcryp->pCrypOutBuffPtr += 16; |
| hcryp->CrypOutCount -= 16; |
| if(hcryp->CrypOutCount == 0) |
| { |
| __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI); |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| /* Call Input transfer complete callback */ |
| HAL_CRYP_OutCpltCallback(hcryp); |
| } |
| } |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in AES CBC decryption mode using IT. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 16 |
| * @param pPlainData Pointer to the plaintext buffer |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESCBC_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) |
| { |
| |
| uint32_t tickstart = 0; |
| uint32_t inputaddr; |
| uint32_t outputaddr; |
| |
| if(hcryp->State == HAL_CRYP_STATE_READY) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| /* Get the buffer addresses and sizes */ |
| hcryp->CrypInCount = Size; |
| hcryp->pCrypInBuffPtr = pCypherData; |
| hcryp->pCrypOutBuffPtr = pPlainData; |
| hcryp->CrypOutCount = Size; |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Check if initialization phase has already been performed */ |
| if(hcryp->Phase == HAL_CRYP_PHASE_READY) |
| { |
| /* Set the key */ |
| CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); |
| |
| /* Set the CRYP peripheral in AES Key mode */ |
| __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_KEY | CRYP_CR_ALGODIR); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Get tick */ |
| tickstart = HAL_GetTick(); |
| |
| while(HAL_IS_BIT_SET(hcryp->Instance->SR, CRYP_FLAG_BUSY)) |
| { |
| /* Check for the Timeout */ |
| if((HAL_GetTick() - tickstart ) > CRYP_TIMEOUT_VALUE) |
| { |
| /* Change state */ |
| hcryp->State = HAL_CRYP_STATE_TIMEOUT; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| return HAL_TIMEOUT; |
| } |
| } |
| |
| /* Reset the ALGOMODE bits*/ |
| CRYP->CR &= (uint32_t)(~CRYP_CR_ALGOMODE); |
| |
| /* Set the CRYP peripheral in AES CBC decryption mode */ |
| __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CBC | CRYP_CR_ALGODIR); |
| |
| /* Set the Initialization Vector */ |
| CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B); |
| |
| /* Flush FIFO */ |
| __HAL_CRYP_FIFO_FLUSH(hcryp); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Set the phase */ |
| hcryp->Phase = HAL_CRYP_PHASE_PROCESS; |
| } |
| |
| /* Enable Interrupts */ |
| __HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI)) |
| { |
| inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; |
| /* Write the Input block in the IN FIFO */ |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| hcryp->pCrypInBuffPtr += 16; |
| hcryp->CrypInCount -= 16; |
| if(hcryp->CrypInCount == 0) |
| { |
| __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI); |
| /* Call the Input data transfer complete callback */ |
| HAL_CRYP_InCpltCallback(hcryp); |
| } |
| } |
| else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI)) |
| { |
| outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; |
| /* Read the Output block from the Output FIFO */ |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| hcryp->pCrypOutBuffPtr += 16; |
| hcryp->CrypOutCount -= 16; |
| if(hcryp->CrypOutCount == 0) |
| { |
| __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI); |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| /* Call Input transfer complete callback */ |
| HAL_CRYP_OutCpltCallback(hcryp); |
| } |
| } |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in AES CTR decryption mode using Interrupt. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 16 |
| * @param pPlainData Pointer to the plaintext buffer |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESCTR_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) |
| { |
| uint32_t inputaddr; |
| uint32_t outputaddr; |
| |
| if(hcryp->State == HAL_CRYP_STATE_READY) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| /* Get the buffer addresses and sizes */ |
| hcryp->CrypInCount = Size; |
| hcryp->pCrypInBuffPtr = pCypherData; |
| hcryp->pCrypOutBuffPtr = pPlainData; |
| hcryp->CrypOutCount = Size; |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Check if initialization phase has already been performed */ |
| if(hcryp->Phase == HAL_CRYP_PHASE_READY) |
| { |
| /* Set the key */ |
| CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); |
| |
| /* Set the CRYP peripheral in AES CTR mode */ |
| __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CTR | CRYP_CR_ALGODIR); |
| |
| /* Set the Initialization Vector */ |
| CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B); |
| |
| /* Flush FIFO */ |
| __HAL_CRYP_FIFO_FLUSH(hcryp); |
| |
| /* Set the phase */ |
| hcryp->Phase = HAL_CRYP_PHASE_PROCESS; |
| } |
| |
| /* Enable Interrupts */ |
| __HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI)) |
| { |
| inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; |
| /* Write the Input block in the IN FIFO */ |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| hcryp->pCrypInBuffPtr += 16; |
| hcryp->CrypInCount -= 16; |
| if(hcryp->CrypInCount == 0) |
| { |
| __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI); |
| /* Call the Input data transfer complete callback */ |
| HAL_CRYP_InCpltCallback(hcryp); |
| } |
| } |
| else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI)) |
| { |
| outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; |
| /* Read the Output block from the Output FIFO */ |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| hcryp->pCrypOutBuffPtr += 16; |
| hcryp->CrypOutCount -= 16; |
| if(hcryp->CrypOutCount == 0) |
| { |
| __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI); |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| /* Call Input transfer complete callback */ |
| HAL_CRYP_OutCpltCallback(hcryp); |
| } |
| } |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in AES ECB encryption mode using DMA. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 16 bytes |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESECB_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) |
| { |
| uint32_t inputaddr; |
| uint32_t outputaddr; |
| |
| if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| inputaddr = (uint32_t)pPlainData; |
| outputaddr = (uint32_t)pCypherData; |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Check if initialization phase has already been performed */ |
| if(hcryp->Phase == HAL_CRYP_PHASE_READY) |
| { |
| /* Set the key */ |
| CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); |
| |
| /* Set the CRYP peripheral in AES ECB mode */ |
| __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_ECB); |
| |
| /* Flush FIFO */ |
| __HAL_CRYP_FIFO_FLUSH(hcryp); |
| |
| /* Set the phase */ |
| hcryp->Phase = HAL_CRYP_PHASE_PROCESS; |
| } |
| /* Set the input and output addresses and start DMA transfer */ |
| CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| else |
| { |
| return HAL_ERROR; |
| } |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in AES CBC encryption mode using DMA. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 16. |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESCBC_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) |
| { |
| uint32_t inputaddr; |
| uint32_t outputaddr; |
| |
| if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| inputaddr = (uint32_t)pPlainData; |
| outputaddr = (uint32_t)pCypherData; |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Check if initialization phase has already been performed */ |
| if(hcryp->Phase == HAL_CRYP_PHASE_READY) |
| { |
| /* Set the key */ |
| CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); |
| |
| /* Set the CRYP peripheral in AES ECB mode */ |
| __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CBC); |
| |
| /* Set the Initialization Vector */ |
| CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B); |
| |
| /* Flush FIFO */ |
| __HAL_CRYP_FIFO_FLUSH(hcryp); |
| |
| /* Set the phase */ |
| hcryp->Phase = HAL_CRYP_PHASE_PROCESS; |
| } |
| /* Set the input and output addresses and start DMA transfer */ |
| CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| else |
| { |
| return HAL_ERROR; |
| } |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in AES CTR encryption mode using DMA. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 16. |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESCTR_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) |
| { |
| uint32_t inputaddr; |
| uint32_t outputaddr; |
| |
| if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| inputaddr = (uint32_t)pPlainData; |
| outputaddr = (uint32_t)pCypherData; |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Check if initialization phase has already been performed */ |
| if(hcryp->Phase == HAL_CRYP_PHASE_READY) |
| { |
| /* Set the key */ |
| CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); |
| |
| /* Set the CRYP peripheral in AES ECB mode */ |
| __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CTR); |
| |
| /* Set the Initialization Vector */ |
| CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B); |
| |
| /* Flush FIFO */ |
| __HAL_CRYP_FIFO_FLUSH(hcryp); |
| |
| /* Set the phase */ |
| hcryp->Phase = HAL_CRYP_PHASE_PROCESS; |
| } |
| |
| /* Set the input and output addresses and start DMA transfer */ |
| CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| else |
| { |
| return HAL_ERROR; |
| } |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in AES ECB decryption mode using DMA. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 16 bytes |
| * @param pPlainData Pointer to the plaintext buffer |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESECB_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) |
| { |
| uint32_t tickstart = 0; |
| uint32_t inputaddr; |
| uint32_t outputaddr; |
| |
| if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| inputaddr = (uint32_t)pCypherData; |
| outputaddr = (uint32_t)pPlainData; |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Check if initialization phase has already been performed */ |
| if(hcryp->Phase == HAL_CRYP_PHASE_READY) |
| { |
| /* Set the key */ |
| CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); |
| |
| /* Set the CRYP peripheral in AES Key mode */ |
| __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_KEY | CRYP_CR_ALGODIR); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Get tick */ |
| tickstart = HAL_GetTick(); |
| |
| while(HAL_IS_BIT_SET(hcryp->Instance->SR, CRYP_FLAG_BUSY)) |
| { |
| /* Check for the Timeout */ |
| if((HAL_GetTick() - tickstart ) > CRYP_TIMEOUT_VALUE) |
| { |
| /* Change state */ |
| hcryp->State = HAL_CRYP_STATE_TIMEOUT; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| return HAL_TIMEOUT; |
| } |
| } |
| |
| /* Reset the ALGOMODE bits*/ |
| CRYP->CR &= (uint32_t)(~CRYP_CR_ALGOMODE); |
| |
| /* Set the CRYP peripheral in AES ECB decryption mode */ |
| __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_ECB | CRYP_CR_ALGODIR); |
| |
| /* Flush FIFO */ |
| __HAL_CRYP_FIFO_FLUSH(hcryp); |
| |
| /* Set the phase */ |
| hcryp->Phase = HAL_CRYP_PHASE_PROCESS; |
| } |
| |
| /* Set the input and output addresses and start DMA transfer */ |
| CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| else |
| { |
| return HAL_ERROR; |
| } |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in AES CBC encryption mode using DMA. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 16 bytes |
| * @param pPlainData Pointer to the plaintext buffer |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESCBC_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) |
| { |
| uint32_t tickstart = 0; |
| uint32_t inputaddr; |
| uint32_t outputaddr; |
| |
| if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| inputaddr = (uint32_t)pCypherData; |
| outputaddr = (uint32_t)pPlainData; |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Check if initialization phase has already been performed */ |
| if(hcryp->Phase == HAL_CRYP_PHASE_READY) |
| { |
| /* Set the key */ |
| CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); |
| |
| /* Set the CRYP peripheral in AES Key mode */ |
| __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_KEY | CRYP_CR_ALGODIR); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Get tick */ |
| tickstart = HAL_GetTick(); |
| |
| while(HAL_IS_BIT_SET(hcryp->Instance->SR, CRYP_FLAG_BUSY)) |
| { |
| /* Check for the Timeout */ |
| if((HAL_GetTick() - tickstart ) > CRYP_TIMEOUT_VALUE) |
| { |
| /* Change state */ |
| hcryp->State = HAL_CRYP_STATE_TIMEOUT; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| return HAL_TIMEOUT; |
| } |
| } |
| |
| /* Reset the ALGOMODE bits*/ |
| CRYP->CR &= (uint32_t)(~CRYP_CR_ALGOMODE); |
| |
| /* Set the CRYP peripheral in AES CBC decryption mode */ |
| __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CBC | CRYP_CR_ALGODIR); |
| |
| /* Set the Initialization Vector */ |
| CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B); |
| |
| /* Flush FIFO */ |
| __HAL_CRYP_FIFO_FLUSH(hcryp); |
| |
| /* Set the phase */ |
| hcryp->Phase = HAL_CRYP_PHASE_PROCESS; |
| } |
| |
| /* Set the input and output addresses and start DMA transfer */ |
| CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| else |
| { |
| return HAL_ERROR; |
| } |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in AES CTR decryption mode using DMA. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 16 |
| * @param pPlainData Pointer to the plaintext buffer |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESCTR_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) |
| { |
| uint32_t inputaddr; |
| uint32_t outputaddr; |
| |
| if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| inputaddr = (uint32_t)pCypherData; |
| outputaddr = (uint32_t)pPlainData; |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Check if initialization phase has already been performed */ |
| if(hcryp->Phase == HAL_CRYP_PHASE_READY) |
| { |
| /* Set the key */ |
| CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); |
| |
| /* Set the CRYP peripheral in AES CTR mode */ |
| __HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CTR | CRYP_CR_ALGODIR); |
| |
| /* Set the Initialization Vector */ |
| CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B); |
| |
| /* Flush FIFO */ |
| __HAL_CRYP_FIFO_FLUSH(hcryp); |
| |
| /* Set the phase */ |
| hcryp->Phase = HAL_CRYP_PHASE_PROCESS; |
| } |
| |
| /* Set the input and output addresses and start DMA transfer */ |
| CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| else |
| { |
| return HAL_ERROR; |
| } |
| } |
| |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup CRYP_Exported_Functions_Group3 DES processing functions |
| * @brief processing functions. |
| * |
| @verbatim |
| ============================================================================== |
| ##### DES processing functions ##### |
| ============================================================================== |
| [..] This section provides functions allowing to: |
| (+) Encrypt plaintext using DES using ECB or CBC chaining modes |
| (+) Decrypt cyphertext using ECB or CBC chaining modes |
| [..] Three processing functions are available: |
| (+) Polling mode |
| (+) Interrupt mode |
| (+) DMA mode |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief Initializes the CRYP peripheral in DES ECB encryption mode. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 8 |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Timeout Specify Timeout value |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_DESECB_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Set CRYP peripheral in DES ECB encryption mode */ |
| CRYP_SetDESECBMode(hcryp, 0); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Write Plain Data and Get Cypher Data */ |
| if(CRYP_ProcessData2Words(hcryp, pPlainData, Size, pCypherData, Timeout) != HAL_OK) |
| { |
| return HAL_TIMEOUT; |
| } |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in DES ECB decryption mode. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 8 |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Timeout Specify Timeout value |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_DESECB_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Set CRYP peripheral in DES ECB decryption mode */ |
| CRYP_SetDESECBMode(hcryp, CRYP_CR_ALGODIR); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Write Plain Data and Get Cypher Data */ |
| if(CRYP_ProcessData2Words(hcryp, pCypherData, Size, pPlainData, Timeout) != HAL_OK) |
| { |
| return HAL_TIMEOUT; |
| } |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in DES CBC encryption mode. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 8 |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Timeout Specify Timeout value |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_DESCBC_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Set CRYP peripheral in DES CBC encryption mode */ |
| CRYP_SetDESCBCMode(hcryp, 0); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Write Plain Data and Get Cypher Data */ |
| if(CRYP_ProcessData2Words(hcryp, pPlainData, Size, pCypherData, Timeout) != HAL_OK) |
| { |
| return HAL_TIMEOUT; |
| } |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in DES ECB decryption mode. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 8 |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Timeout Specify Timeout value |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_DESCBC_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Set CRYP peripheral in DES CBC decryption mode */ |
| CRYP_SetDESCBCMode(hcryp, CRYP_CR_ALGODIR); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Write Plain Data and Get Cypher Data */ |
| if(CRYP_ProcessData2Words(hcryp, pCypherData, Size, pPlainData, Timeout) != HAL_OK) |
| { |
| return HAL_TIMEOUT; |
| } |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in DES ECB encryption mode using IT. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 8 |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_DESECB_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) |
| { |
| uint32_t inputaddr; |
| uint32_t outputaddr; |
| |
| if(hcryp->State == HAL_CRYP_STATE_READY) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| hcryp->CrypInCount = Size; |
| hcryp->pCrypInBuffPtr = pPlainData; |
| hcryp->pCrypOutBuffPtr = pCypherData; |
| hcryp->CrypOutCount = Size; |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Set CRYP peripheral in DES ECB encryption mode */ |
| CRYP_SetDESECBMode(hcryp, 0); |
| |
| /* Enable Interrupts */ |
| __HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI)) |
| { |
| inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; |
| /* Write the Input block in the IN FIFO */ |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| |
| hcryp->pCrypInBuffPtr += 8; |
| hcryp->CrypInCount -= 8; |
| if(hcryp->CrypInCount == 0) |
| { |
| __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI); |
| /* Call the Input data transfer complete callback */ |
| HAL_CRYP_InCpltCallback(hcryp); |
| } |
| } |
| else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI)) |
| { |
| outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; |
| /* Read the Output block from the Output FIFO */ |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| |
| hcryp->pCrypOutBuffPtr += 8; |
| hcryp->CrypOutCount -= 8; |
| if(hcryp->CrypOutCount == 0) |
| { |
| /* Disable IT */ |
| __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI); |
| /* Disable CRYP */ |
| __HAL_CRYP_DISABLE(hcryp); |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| /* Call Input transfer complete callback */ |
| HAL_CRYP_OutCpltCallback(hcryp); |
| } |
| } |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in DES CBC encryption mode using interrupt. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 8 |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_DESCBC_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) |
| { |
| uint32_t inputaddr; |
| uint32_t outputaddr; |
| |
| if(hcryp->State == HAL_CRYP_STATE_READY) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| hcryp->CrypInCount = Size; |
| hcryp->pCrypInBuffPtr = pPlainData; |
| hcryp->pCrypOutBuffPtr = pCypherData; |
| hcryp->CrypOutCount = Size; |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Set CRYP peripheral in DES CBC encryption mode */ |
| CRYP_SetDESCBCMode(hcryp, 0); |
| |
| /* Enable Interrupts */ |
| __HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI)) |
| { |
| inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; |
| /* Write the Input block in the IN FIFO */ |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| |
| hcryp->pCrypInBuffPtr += 8; |
| hcryp->CrypInCount -= 8; |
| if(hcryp->CrypInCount == 0) |
| { |
| __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI); |
| /* Call the Input data transfer complete callback */ |
| HAL_CRYP_InCpltCallback(hcryp); |
| } |
| } |
| else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI)) |
| { |
| outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; |
| /* Read the Output block from the Output FIFO */ |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| |
| hcryp->pCrypOutBuffPtr += 8; |
| hcryp->CrypOutCount -= 8; |
| if(hcryp->CrypOutCount == 0) |
| { |
| /* Disable IT */ |
| __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI); |
| /* Disable CRYP */ |
| __HAL_CRYP_DISABLE(hcryp); |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| /* Call Input transfer complete callback */ |
| HAL_CRYP_OutCpltCallback(hcryp); |
| } |
| } |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in DES ECB decryption mode using IT. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 8 |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_DESECB_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) |
| { |
| uint32_t inputaddr; |
| uint32_t outputaddr; |
| |
| if(hcryp->State == HAL_CRYP_STATE_READY) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| hcryp->CrypInCount = Size; |
| hcryp->pCrypInBuffPtr = pCypherData; |
| hcryp->pCrypOutBuffPtr = pPlainData; |
| hcryp->CrypOutCount = Size; |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Set CRYP peripheral in DES ECB decryption mode */ |
| CRYP_SetDESECBMode(hcryp, CRYP_CR_ALGODIR); |
| |
| /* Enable Interrupts */ |
| __HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI)) |
| { |
| inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; |
| /* Write the Input block in the IN FIFO */ |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| |
| hcryp->pCrypInBuffPtr += 8; |
| hcryp->CrypInCount -= 8; |
| if(hcryp->CrypInCount == 0) |
| { |
| __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI); |
| /* Call the Input data transfer complete callback */ |
| HAL_CRYP_InCpltCallback(hcryp); |
| } |
| } |
| else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI)) |
| { |
| outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; |
| /* Read the Output block from the Output FIFO */ |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| |
| hcryp->pCrypOutBuffPtr += 8; |
| hcryp->CrypOutCount -= 8; |
| if(hcryp->CrypOutCount == 0) |
| { |
| /* Disable IT */ |
| __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI); |
| /* Disable CRYP */ |
| __HAL_CRYP_DISABLE(hcryp); |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| /* Call Input transfer complete callback */ |
| HAL_CRYP_OutCpltCallback(hcryp); |
| } |
| } |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in DES ECB decryption mode using interrupt. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 8 |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_DESCBC_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) |
| { |
| uint32_t inputaddr; |
| uint32_t outputaddr; |
| |
| if(hcryp->State == HAL_CRYP_STATE_READY) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| hcryp->CrypInCount = Size; |
| hcryp->pCrypInBuffPtr = pCypherData; |
| hcryp->pCrypOutBuffPtr = pPlainData; |
| hcryp->CrypOutCount = Size; |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Set CRYP peripheral in DES CBC decryption mode */ |
| CRYP_SetDESCBCMode(hcryp, CRYP_CR_ALGODIR); |
| |
| /* Enable Interrupts */ |
| __HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI)) |
| { |
| inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; |
| /* Write the Input block in the IN FIFO */ |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| |
| hcryp->pCrypInBuffPtr += 8; |
| hcryp->CrypInCount -= 8; |
| if(hcryp->CrypInCount == 0) |
| { |
| __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI); |
| /* Call the Input data transfer complete callback */ |
| HAL_CRYP_InCpltCallback(hcryp); |
| } |
| } |
| else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI)) |
| { |
| outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; |
| /* Read the Output block from the Output FIFO */ |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| |
| hcryp->pCrypOutBuffPtr += 8; |
| hcryp->CrypOutCount -= 8; |
| if(hcryp->CrypOutCount == 0) |
| { |
| /* Disable IT */ |
| __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI); |
| /* Disable CRYP */ |
| __HAL_CRYP_DISABLE(hcryp); |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| /* Call Input transfer complete callback */ |
| HAL_CRYP_OutCpltCallback(hcryp); |
| } |
| } |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in DES ECB encryption mode using DMA. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 8 |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_DESECB_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) |
| { |
| uint32_t inputaddr; |
| uint32_t outputaddr; |
| |
| if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| inputaddr = (uint32_t)pPlainData; |
| outputaddr = (uint32_t)pCypherData; |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Set CRYP peripheral in DES ECB encryption mode */ |
| CRYP_SetDESECBMode(hcryp, 0); |
| |
| /* Set the input and output addresses and start DMA transfer */ |
| CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| else |
| { |
| return HAL_ERROR; |
| } |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in DES CBC encryption mode using DMA. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 8 |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_DESCBC_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) |
| { |
| uint32_t inputaddr; |
| uint32_t outputaddr; |
| |
| if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| inputaddr = (uint32_t)pPlainData; |
| outputaddr = (uint32_t)pCypherData; |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Set CRYP peripheral in DES CBC encryption mode */ |
| CRYP_SetDESCBCMode(hcryp, 0); |
| |
| /* Set the input and output addresses and start DMA transfer */ |
| CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| else |
| { |
| return HAL_ERROR; |
| } |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in DES ECB decryption mode using DMA. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 8 |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_DESECB_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) |
| { |
| uint32_t inputaddr; |
| uint32_t outputaddr; |
| |
| if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| inputaddr = (uint32_t)pCypherData; |
| outputaddr = (uint32_t)pPlainData; |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Set CRYP peripheral in DES ECB decryption mode */ |
| CRYP_SetDESECBMode(hcryp, CRYP_CR_ALGODIR); |
| |
| /* Set the input and output addresses and start DMA transfer */ |
| CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| else |
| { |
| return HAL_ERROR; |
| } |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in DES ECB decryption mode using DMA. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 8 |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_DESCBC_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) |
| { |
| uint32_t inputaddr; |
| uint32_t outputaddr; |
| |
| if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| inputaddr = (uint32_t)pCypherData; |
| outputaddr = (uint32_t)pPlainData; |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Set CRYP peripheral in DES CBC decryption mode */ |
| CRYP_SetDESCBCMode(hcryp, CRYP_CR_ALGODIR); |
| |
| /* Set the input and output addresses and start DMA transfer */ |
| CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| else |
| { |
| return HAL_ERROR; |
| } |
| } |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup CRYP_Exported_Functions_Group4 TDES processing functions |
| * @brief processing functions. |
| * |
| @verbatim |
| ============================================================================== |
| ##### TDES processing functions ##### |
| ============================================================================== |
| [..] This section provides functions allowing to: |
| (+) Encrypt plaintext using TDES based on ECB or CBC chaining modes |
| (+) Decrypt cyphertext using TDES based on ECB or CBC chaining modes |
| [..] Three processing functions are available: |
| (+) Polling mode |
| (+) Interrupt mode |
| (+) DMA mode |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief Initializes the CRYP peripheral in TDES ECB encryption mode |
| * then encrypt pPlainData. The cypher data are available in pCypherData |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 8 |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Timeout Specify Timeout value |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_TDESECB_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Set CRYP peripheral in TDES ECB encryption mode */ |
| CRYP_SetTDESECBMode(hcryp, 0); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Write Plain Data and Get Cypher Data */ |
| if(CRYP_ProcessData2Words(hcryp, pPlainData, Size, pCypherData, Timeout) != HAL_OK) |
| { |
| return HAL_TIMEOUT; |
| } |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in TDES ECB decryption mode |
| * then decrypted pCypherData. The cypher data are available in pPlainData |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 8 |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Timeout Specify Timeout value |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_TDESECB_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Set CRYP peripheral in TDES ECB decryption mode */ |
| CRYP_SetTDESECBMode(hcryp, CRYP_CR_ALGODIR); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Write Cypher Data and Get Plain Data */ |
| if(CRYP_ProcessData2Words(hcryp, pCypherData, Size, pPlainData, Timeout) != HAL_OK) |
| { |
| return HAL_TIMEOUT; |
| } |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in TDES CBC encryption mode |
| * then encrypt pPlainData. The cypher data are available in pCypherData |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 8 |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Timeout Specify Timeout value |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_TDESCBC_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Set CRYP peripheral in TDES CBC encryption mode */ |
| CRYP_SetTDESCBCMode(hcryp, 0); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Write Plain Data and Get Cypher Data */ |
| if(CRYP_ProcessData2Words(hcryp, pPlainData, Size, pCypherData, Timeout) != HAL_OK) |
| { |
| return HAL_TIMEOUT; |
| } |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in TDES CBC decryption mode |
| * then decrypted pCypherData. The cypher data are available in pPlainData |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 8 |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Timeout Specify Timeout value |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_TDESCBC_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Set CRYP peripheral in TDES CBC decryption mode */ |
| CRYP_SetTDESCBCMode(hcryp, CRYP_CR_ALGODIR); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Write Cypher Data and Get Plain Data */ |
| if(CRYP_ProcessData2Words(hcryp, pCypherData, Size, pPlainData, Timeout) != HAL_OK) |
| { |
| return HAL_TIMEOUT; |
| } |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in TDES ECB encryption mode using interrupt. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 8 |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_TDESECB_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) |
| { |
| uint32_t inputaddr; |
| uint32_t outputaddr; |
| |
| if(hcryp->State == HAL_CRYP_STATE_READY) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| hcryp->CrypInCount = Size; |
| hcryp->pCrypInBuffPtr = pPlainData; |
| hcryp->pCrypOutBuffPtr = pCypherData; |
| hcryp->CrypOutCount = Size; |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Set CRYP peripheral in TDES ECB encryption mode */ |
| CRYP_SetTDESECBMode(hcryp, 0); |
| |
| /* Enable Interrupts */ |
| __HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI)) |
| { |
| inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; |
| /* Write the Input block in the IN FIFO */ |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| |
| hcryp->pCrypInBuffPtr += 8; |
| hcryp->CrypInCount -= 8; |
| if(hcryp->CrypInCount == 0) |
| { |
| __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI); |
| /* Call the Input data transfer complete callback */ |
| HAL_CRYP_InCpltCallback(hcryp); |
| } |
| } |
| else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI)) |
| { |
| outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; |
| /* Read the Output block from the Output FIFO */ |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| |
| hcryp->pCrypOutBuffPtr += 8; |
| hcryp->CrypOutCount -= 8; |
| if(hcryp->CrypOutCount == 0) |
| { |
| /* Disable IT */ |
| __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI); |
| /* Disable CRYP */ |
| __HAL_CRYP_DISABLE(hcryp); |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| /* Call the Output data transfer complete callback */ |
| HAL_CRYP_OutCpltCallback(hcryp); |
| } |
| } |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in TDES CBC encryption mode. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 8 |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_TDESCBC_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) |
| { |
| uint32_t inputaddr; |
| uint32_t outputaddr; |
| |
| if(hcryp->State == HAL_CRYP_STATE_READY) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| hcryp->CrypInCount = Size; |
| hcryp->pCrypInBuffPtr = pPlainData; |
| hcryp->pCrypOutBuffPtr = pCypherData; |
| hcryp->CrypOutCount = Size; |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Set CRYP peripheral in TDES CBC encryption mode */ |
| CRYP_SetTDESCBCMode(hcryp, 0); |
| |
| /* Enable Interrupts */ |
| __HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI)) |
| { |
| inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; |
| /* Write the Input block in the IN FIFO */ |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| |
| hcryp->pCrypInBuffPtr += 8; |
| hcryp->CrypInCount -= 8; |
| if(hcryp->CrypInCount == 0) |
| { |
| __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI); |
| /* Call the Input data transfer complete callback */ |
| HAL_CRYP_InCpltCallback(hcryp); |
| } |
| } |
| else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI)) |
| { |
| outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; |
| /* Read the Output block from the Output FIFO */ |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| |
| hcryp->pCrypOutBuffPtr += 8; |
| hcryp->CrypOutCount -= 8; |
| if(hcryp->CrypOutCount == 0) |
| { |
| __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI); |
| /* Disable CRYP */ |
| __HAL_CRYP_DISABLE(hcryp); |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| /* Call Input transfer complete callback */ |
| HAL_CRYP_OutCpltCallback(hcryp); |
| } |
| } |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in TDES ECB decryption mode. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 8 |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_TDESECB_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) |
| { |
| uint32_t inputaddr; |
| uint32_t outputaddr; |
| |
| if(hcryp->State == HAL_CRYP_STATE_READY) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| hcryp->CrypInCount = Size; |
| hcryp->pCrypInBuffPtr = pCypherData; |
| hcryp->pCrypOutBuffPtr = pPlainData; |
| hcryp->CrypOutCount = Size; |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Set CRYP peripheral in TDES ECB decryption mode */ |
| CRYP_SetTDESECBMode(hcryp, CRYP_CR_ALGODIR); |
| |
| /* Enable Interrupts */ |
| __HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI)) |
| { |
| inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; |
| /* Write the Input block in the IN FIFO */ |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| |
| hcryp->pCrypInBuffPtr += 8; |
| hcryp->CrypInCount -= 8; |
| if(hcryp->CrypInCount == 0) |
| { |
| __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI); |
| /* Call the Input data transfer complete callback */ |
| HAL_CRYP_InCpltCallback(hcryp); |
| } |
| } |
| else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI)) |
| { |
| outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; |
| /* Read the Output block from the Output FIFO */ |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| |
| hcryp->pCrypOutBuffPtr += 8; |
| hcryp->CrypOutCount -= 8; |
| if(hcryp->CrypOutCount == 0) |
| { |
| __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI); |
| /* Disable CRYP */ |
| __HAL_CRYP_DISABLE(hcryp); |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| /* Call Input transfer complete callback */ |
| HAL_CRYP_OutCpltCallback(hcryp); |
| } |
| } |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in TDES CBC decryption mode. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 8 |
| * @param pPlainData Pointer to the plaintext buffer |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_TDESCBC_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) |
| { |
| uint32_t inputaddr; |
| uint32_t outputaddr; |
| |
| if(hcryp->State == HAL_CRYP_STATE_READY) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| hcryp->CrypInCount = Size; |
| hcryp->pCrypInBuffPtr = pCypherData; |
| hcryp->pCrypOutBuffPtr = pPlainData; |
| hcryp->CrypOutCount = Size; |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Set CRYP peripheral in TDES CBC decryption mode */ |
| CRYP_SetTDESCBCMode(hcryp, CRYP_CR_ALGODIR); |
| |
| /* Enable Interrupts */ |
| __HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI); |
| |
| /* Enable CRYP */ |
| __HAL_CRYP_ENABLE(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI)) |
| { |
| inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; |
| /* Write the Input block in the IN FIFO */ |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DR = *(uint32_t*)(inputaddr); |
| |
| hcryp->pCrypInBuffPtr += 8; |
| hcryp->CrypInCount -= 8; |
| if(hcryp->CrypInCount == 0) |
| { |
| __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI); |
| /* Call the Input data transfer complete callback */ |
| HAL_CRYP_InCpltCallback(hcryp); |
| } |
| } |
| else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI)) |
| { |
| outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; |
| /* Read the Output block from the Output FIFO */ |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; |
| |
| hcryp->pCrypOutBuffPtr += 8; |
| hcryp->CrypOutCount -= 8; |
| if(hcryp->CrypOutCount == 0) |
| { |
| __HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI); |
| /* Disable CRYP */ |
| __HAL_CRYP_DISABLE(hcryp); |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| /* Call Input transfer complete callback */ |
| HAL_CRYP_OutCpltCallback(hcryp); |
| } |
| } |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in TDES ECB encryption mode using DMA. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 8 |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_TDESECB_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) |
| { |
| uint32_t inputaddr; |
| uint32_t outputaddr; |
| |
| if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| inputaddr = (uint32_t)pPlainData; |
| outputaddr = (uint32_t)pCypherData; |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Set CRYP peripheral in TDES ECB encryption mode */ |
| CRYP_SetTDESECBMode(hcryp, 0); |
| |
| /* Set the input and output addresses and start DMA transfer */ |
| CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| else |
| { |
| return HAL_ERROR; |
| } |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in TDES CBC encryption mode using DMA. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 8 |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_TDESCBC_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) |
| { |
| uint32_t inputaddr; |
| uint32_t outputaddr; |
| |
| if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| inputaddr = (uint32_t)pPlainData; |
| outputaddr = (uint32_t)pCypherData; |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Set CRYP peripheral in TDES CBC encryption mode */ |
| CRYP_SetTDESCBCMode(hcryp, 0); |
| |
| /* Set the input and output addresses and start DMA transfer */ |
| CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| else |
| { |
| return HAL_ERROR; |
| } |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in TDES ECB decryption mode using DMA. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 8 |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_TDESECB_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) |
| { |
| uint32_t inputaddr; |
| uint32_t outputaddr; |
| |
| if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| inputaddr = (uint32_t)pCypherData; |
| outputaddr = (uint32_t)pPlainData; |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Set CRYP peripheral in TDES ECB decryption mode */ |
| CRYP_SetTDESECBMode(hcryp, CRYP_CR_ALGODIR); |
| |
| /* Set the input and output addresses and start DMA transfer */ |
| CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| else |
| { |
| return HAL_ERROR; |
| } |
| } |
| |
| /** |
| * @brief Initializes the CRYP peripheral in TDES CBC decryption mode using DMA. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 8 |
| * @param pPlainData Pointer to the plaintext buffer |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_TDESCBC_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) |
| { |
| uint32_t inputaddr; |
| uint32_t outputaddr; |
| |
| if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) |
| { |
| /* Process Locked */ |
| __HAL_LOCK(hcryp); |
| |
| inputaddr = (uint32_t)pCypherData; |
| outputaddr = (uint32_t)pPlainData; |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Set CRYP peripheral in TDES CBC decryption mode */ |
| CRYP_SetTDESCBCMode(hcryp, CRYP_CR_ALGODIR); |
| |
| /* Set the input and output addresses and start DMA transfer */ |
| CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| else |
| { |
| return HAL_ERROR; |
| } |
| } |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup CRYP_Exported_Functions_Group5 DMA callback functions |
| * @brief DMA callback functions. |
| * |
| @verbatim |
| ============================================================================== |
| ##### DMA callback functions ##### |
| ============================================================================== |
| [..] This section provides DMA callback functions: |
| (+) DMA Input data transfer complete |
| (+) DMA Output data transfer complete |
| (+) DMA error |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief Input FIFO transfer completed callbacks. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @retval None |
| */ |
| __weak void HAL_CRYP_InCpltCallback(CRYP_HandleTypeDef *hcryp) |
| { |
| /* Prevent unused argument(s) compilation warning */ |
| UNUSED(hcryp); |
| |
| /* NOTE : This function Should not be modified, when the callback is needed, |
| the HAL_CRYP_InCpltCallback could be implemented in the user file |
| */ |
| } |
| |
| /** |
| * @brief Output FIFO transfer completed callbacks. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @retval None |
| */ |
| __weak void HAL_CRYP_OutCpltCallback(CRYP_HandleTypeDef *hcryp) |
| { |
| /* Prevent unused argument(s) compilation warning */ |
| UNUSED(hcryp); |
| |
| /* NOTE : This function Should not be modified, when the callback is needed, |
| the HAL_CRYP_OutCpltCallback could be implemented in the user file |
| */ |
| } |
| |
| /** |
| * @brief CRYP error callbacks. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @retval None |
| */ |
| __weak void HAL_CRYP_ErrorCallback(CRYP_HandleTypeDef *hcryp) |
| { |
| /* Prevent unused argument(s) compilation warning */ |
| UNUSED(hcryp); |
| |
| /* NOTE : This function Should not be modified, when the callback is needed, |
| the HAL_CRYP_ErrorCallback could be implemented in the user file |
| */ |
| } |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup CRYP_Exported_Functions_Group6 CRYP IRQ handler management |
| * @brief CRYP IRQ handler. |
| * |
| @verbatim |
| ============================================================================== |
| ##### CRYP IRQ handler management ##### |
| ============================================================================== |
| [..] This section provides CRYP IRQ handler function. |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief This function handles CRYP interrupt request. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @retval None |
| */ |
| void HAL_CRYP_IRQHandler(CRYP_HandleTypeDef *hcryp) |
| { |
| switch(CRYP->CR & CRYP_CR_ALGOMODE_DIRECTION) |
| { |
| case CRYP_CR_ALGOMODE_TDES_ECB_ENCRYPT: |
| HAL_CRYP_TDESECB_Encrypt_IT(hcryp, NULL, 0, NULL); |
| break; |
| |
| case CRYP_CR_ALGOMODE_TDES_ECB_DECRYPT: |
| HAL_CRYP_TDESECB_Decrypt_IT(hcryp, NULL, 0, NULL); |
| break; |
| |
| case CRYP_CR_ALGOMODE_TDES_CBC_ENCRYPT: |
| HAL_CRYP_TDESCBC_Encrypt_IT(hcryp, NULL, 0, NULL); |
| break; |
| |
| case CRYP_CR_ALGOMODE_TDES_CBC_DECRYPT: |
| HAL_CRYP_TDESCBC_Decrypt_IT(hcryp, NULL, 0, NULL); |
| break; |
| |
| case CRYP_CR_ALGOMODE_DES_ECB_ENCRYPT: |
| HAL_CRYP_DESECB_Encrypt_IT(hcryp, NULL, 0, NULL); |
| break; |
| |
| case CRYP_CR_ALGOMODE_DES_ECB_DECRYPT: |
| HAL_CRYP_DESECB_Decrypt_IT(hcryp, NULL, 0, NULL); |
| break; |
| |
| case CRYP_CR_ALGOMODE_DES_CBC_ENCRYPT: |
| HAL_CRYP_DESCBC_Encrypt_IT(hcryp, NULL, 0, NULL); |
| break; |
| |
| case CRYP_CR_ALGOMODE_DES_CBC_DECRYPT: |
| HAL_CRYP_DESCBC_Decrypt_IT(hcryp, NULL, 0, NULL); |
| break; |
| |
| case CRYP_CR_ALGOMODE_AES_ECB_ENCRYPT: |
| HAL_CRYP_AESECB_Encrypt_IT(hcryp, NULL, 0, NULL); |
| break; |
| |
| case CRYP_CR_ALGOMODE_AES_ECB_DECRYPT: |
| HAL_CRYP_AESECB_Decrypt_IT(hcryp, NULL, 0, NULL); |
| break; |
| |
| case CRYP_CR_ALGOMODE_AES_CBC_ENCRYPT: |
| HAL_CRYP_AESCBC_Encrypt_IT(hcryp, NULL, 0, NULL); |
| break; |
| |
| case CRYP_CR_ALGOMODE_AES_CBC_DECRYPT: |
| HAL_CRYP_AESCBC_Decrypt_IT(hcryp, NULL, 0, NULL); |
| break; |
| |
| case CRYP_CR_ALGOMODE_AES_CTR_ENCRYPT: |
| HAL_CRYP_AESCTR_Encrypt_IT(hcryp, NULL, 0, NULL); |
| break; |
| |
| case CRYP_CR_ALGOMODE_AES_CTR_DECRYPT: |
| HAL_CRYP_AESCTR_Decrypt_IT(hcryp, NULL, 0, NULL); |
| break; |
| |
| default: |
| break; |
| } |
| } |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup CRYP_Exported_Functions_Group7 Peripheral State functions |
| * @brief Peripheral State functions. |
| * |
| @verbatim |
| ============================================================================== |
| ##### Peripheral State functions ##### |
| ============================================================================== |
| [..] |
| This subsection permits to get in run-time the status of the peripheral. |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief Returns the CRYP state. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @retval HAL state |
| */ |
| HAL_CRYP_STATETypeDef HAL_CRYP_GetState(CRYP_HandleTypeDef *hcryp) |
| { |
| return hcryp->State; |
| } |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| /** |
| * @} |
| */ |
| /** |
| * @} |
| */ |
| #endif /* CRYP */ |
| |
| #if defined (AES) |
| |
| |
| /** @addtogroup STM32F7xx_HAL_Driver |
| * @{ |
| */ |
| |
| /** @defgroup AES AES |
| * @brief AES HAL module driver. |
| * @{ |
| */ |
| |
| |
| |
| /* Private typedef -----------------------------------------------------------*/ |
| /* Private define ------------------------------------------------------------*/ |
| /* Private macro -------------------------------------------------------------*/ |
| /* Private variables ---------------------------------------------------------*/ |
| /* Private functions --------------------------------------------------------*/ |
| |
| /** @defgroup CRYP_Private_Functions CRYP Private Functions |
| * @{ |
| */ |
| |
| static HAL_StatusTypeDef CRYP_SetInitVector(CRYP_HandleTypeDef *hcryp); |
| static HAL_StatusTypeDef CRYP_SetKey(CRYP_HandleTypeDef *hcryp); |
| static HAL_StatusTypeDef CRYP_AES_IT(CRYP_HandleTypeDef *hcryp); |
| |
| /** |
| * @} |
| */ |
| |
| /* Exported functions ---------------------------------------------------------*/ |
| |
| /** @defgroup CRYP_Exported_Functions CRYP Exported Functions |
| * @{ |
| */ |
| |
| /** @defgroup CRYP_Exported_Functions_Group1 Initialization and deinitialization functions |
| * @brief Initialization and Configuration functions. |
| * |
| @verbatim |
| ============================================================================== |
| ##### Initialization and deinitialization functions ##### |
| ============================================================================== |
| [..] This section provides functions allowing to: |
| (+) Initialize the CRYP according to the specified parameters |
| in the CRYP_InitTypeDef and creates the associated handle |
| (+) DeInitialize the CRYP peripheral |
| (+) Initialize the CRYP MSP (MCU Specific Package) |
| (+) De-Initialize the CRYP MSP |
| |
| [..] |
| (@) Specific care must be taken to format the key and the Initialization Vector IV! |
| |
| [..] If the key is defined as a 128-bit long array key[127..0] = {b127 ... b0} where |
| b127 is the MSB and b0 the LSB, the key must be stored in MCU memory |
| (+) as a sequence of words where the MSB word comes first (occupies the |
| lowest memory address) |
| (+) where each word is byte-swapped: |
| (++) address n+0 : 0b b103 .. b96 b111 .. b104 b119 .. b112 b127 .. b120 |
| (++) address n+4 : 0b b71 .. b64 b79 .. b72 b87 .. b80 b95 .. b88 |
| (++) address n+8 : 0b b39 .. b32 b47 .. b40 b55 .. b48 b63 .. b56 |
| (++) address n+C : 0b b7 .. b0 b15 .. b8 b23 .. b16 b31 .. b24 |
| [..] Hereafter, another illustration when considering a 128-bit long key made of 16 bytes {B15..B0}. |
| The 4 32-bit words that make the key must be stored as follows in MCU memory: |
| (+) address n+0 : 0x B12 B13 B14 B15 |
| (+) address n+4 : 0x B8 B9 B10 B11 |
| (+) address n+8 : 0x B4 B5 B6 B7 |
| (+) address n+C : 0x B0 B1 B2 B3 |
| [..] which leads to the expected setting |
| (+) AES_KEYR3 = 0x B15 B14 B13 B12 |
| (+) AES_KEYR2 = 0x B11 B10 B9 B8 |
| (+) AES_KEYR1 = 0x B7 B6 B5 B4 |
| (+) AES_KEYR0 = 0x B3 B2 B1 B0 |
| |
| [..] Same format must be applied for a 256-bit long key made of 32 bytes {B31..B0}. |
| The 8 32-bit words that make the key must be stored as follows in MCU memory: |
| (+) address n+00 : 0x B28 B29 B30 B31 |
| (+) address n+04 : 0x B24 B25 B26 B27 |
| (+) address n+08 : 0x B20 B21 B22 B23 |
| (+) address n+0C : 0x B16 B17 B18 B19 |
| (+) address n+10 : 0x B12 B13 B14 B15 |
| (+) address n+14 : 0x B8 B9 B10 B11 |
| (+) address n+18 : 0x B4 B5 B6 B7 |
| (+) address n+1C : 0x B0 B1 B2 B3 |
| [..] which leads to the expected setting |
| (+) AES_KEYR7 = 0x B31 B30 B29 B28 |
| (+) AES_KEYR6 = 0x B27 B26 B25 B24 |
| (+) AES_KEYR5 = 0x B23 B22 B21 B20 |
| (+) AES_KEYR4 = 0x B19 B18 B17 B16 |
| (+) AES_KEYR3 = 0x B15 B14 B13 B12 |
| (+) AES_KEYR2 = 0x B11 B10 B9 B8 |
| (+) AES_KEYR1 = 0x B7 B6 B5 B4 |
| (+) AES_KEYR0 = 0x B3 B2 B1 B0 |
| |
| [..] Initialization Vector IV (4 32-bit words) format must follow the same as |
| that of a 128-bit long key. |
| |
| [..] |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief Initialize the CRYP according to the specified |
| * parameters in the CRYP_InitTypeDef and initialize the associated handle. |
| * @note Specific care must be taken to format the key and the Initialization Vector IV |
| * stored in the MCU memory before calling HAL_CRYP_Init(). Refer to explanations |
| * hereabove. |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_Init(CRYP_HandleTypeDef *hcryp) |
| { |
| /* Check the CRYP handle allocation */ |
| if(hcryp == NULL) |
| { |
| return HAL_ERROR; |
| } |
| |
| /* Check the instance */ |
| assert_param(IS_AES_ALL_INSTANCE(hcryp->Instance)); |
| |
| /* Check the parameters */ |
| assert_param(IS_CRYP_KEYSIZE(hcryp->Init.KeySize)); |
| assert_param(IS_CRYP_DATATYPE(hcryp->Init.DataType)); |
| assert_param(IS_CRYP_ALGOMODE(hcryp->Init.OperatingMode)); |
| /* ChainingMode parameter is irrelevant when mode is set to Key derivation */ |
| if (hcryp->Init.OperatingMode != CRYP_ALGOMODE_KEYDERIVATION) |
| { |
| assert_param(IS_CRYP_CHAINMODE(hcryp->Init.ChainingMode)); |
| } |
| assert_param(IS_CRYP_WRITE(hcryp->Init.KeyWriteFlag)); |
| |
| /*========================================================*/ |
| /* Check the proper operating/chaining modes combinations */ |
| /*========================================================*/ |
| /* Check the proper chaining when the operating mode is key derivation and decryption */ |
| #if defined(AES_CR_NPBLB) |
| if ((hcryp->Init.OperatingMode == CRYP_ALGOMODE_KEYDERIVATION_DECRYPT) &&\ |
| ((hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CTR) \ |
| || (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_GCM_GMAC) \ |
| || (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CCM_CMAC))) |
| #else |
| if ((hcryp->Init.OperatingMode == CRYP_ALGOMODE_KEYDERIVATION_DECRYPT) &&\ |
| ((hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CTR) \ |
| || (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_GCM_GMAC) \ |
| || (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CMAC))) |
| #endif |
| { |
| return HAL_ERROR; |
| } |
| /* Check that key derivation is not set in CMAC mode or CCM mode when applicable */ |
| #if defined(AES_CR_NPBLB) |
| if ((hcryp->Init.OperatingMode == CRYP_ALGOMODE_KEYDERIVATION) |
| && (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CCM_CMAC)) |
| #else |
| if ((hcryp->Init.OperatingMode == CRYP_ALGOMODE_KEYDERIVATION) |
| && (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CMAC)) |
| #endif |
| { |
| return HAL_ERROR; |
| } |
| |
| |
| /*================*/ |
| /* Initialization */ |
| /*================*/ |
| /* Initialization start */ |
| if(hcryp->State == HAL_CRYP_STATE_RESET) |
| { |
| /* Allocate lock resource and initialize it */ |
| hcryp->Lock = HAL_UNLOCKED; |
| |
| /* Init the low level hardware */ |
| HAL_CRYP_MspInit(hcryp); |
| } |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Disable the Peripheral */ |
| __HAL_CRYP_DISABLE(); |
| |
| /*=============================================================*/ |
| /* AES initialization common to all operating modes */ |
| /*=============================================================*/ |
| /* Set the Key size selection */ |
| MODIFY_REG(hcryp->Instance->CR, AES_CR_KEYSIZE, hcryp->Init.KeySize); |
| |
| /* Set the default CRYP phase when this parameter is not used. |
| Phase is updated below in case of GCM/GMAC/CMAC(/CCM) setting. */ |
| hcryp->Phase = HAL_CRYP_PHASE_NOT_USED; |
| |
| |
| |
| /*=============================================================*/ |
| /* Carry on the initialization based on the AES operating mode */ |
| /*=============================================================*/ |
| /* Key derivation */ |
| if (hcryp->Init.OperatingMode == CRYP_ALGOMODE_KEYDERIVATION) |
| { |
| MODIFY_REG(hcryp->Instance->CR, AES_CR_MODE, CRYP_ALGOMODE_KEYDERIVATION); |
| |
| /* Configure the Key registers */ |
| if (CRYP_SetKey(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| } |
| else |
| /* Encryption / Decryption (with or without key derivation) / authentication */ |
| { |
| /* Set data type, operating and chaining modes. |
| In case of GCM or GMAC, data type is forced to 0b00 */ |
| if (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_GCM_GMAC) |
| { |
| MODIFY_REG(hcryp->Instance->CR, AES_CR_DATATYPE|AES_CR_MODE|AES_CR_CHMOD, hcryp->Init.OperatingMode|hcryp->Init.ChainingMode); |
| } |
| else |
| { |
| MODIFY_REG(hcryp->Instance->CR, AES_CR_DATATYPE|AES_CR_MODE|AES_CR_CHMOD, hcryp->Init.DataType|hcryp->Init.OperatingMode|hcryp->Init.ChainingMode); |
| } |
| |
| |
| /* Specify the encryption/decryption phase in case of Galois counter mode (GCM), |
| Galois message authentication code (GMAC), cipher message authentication code (CMAC) |
| or Counter with Cipher Mode (CCM) when applicable */ |
| #if defined(AES_CR_NPBLB) |
| if ((hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_GCM_GMAC) |
| || (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CCM_CMAC)) |
| #else |
| if ((hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_GCM_GMAC) |
| || (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CMAC)) |
| #endif |
| { |
| MODIFY_REG(hcryp->Instance->CR, AES_CR_GCMPH, hcryp->Init.GCMCMACPhase); |
| hcryp->Phase = HAL_CRYP_PHASE_START; |
| } |
| |
| |
| /* Configure the Key registers if no need to bypass this step */ |
| if (hcryp->Init.KeyWriteFlag == CRYP_KEY_WRITE_ENABLE) |
| { |
| if (CRYP_SetKey(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| } |
| |
| /* If applicable, configure the Initialization Vector */ |
| if (hcryp->Init.ChainingMode != CRYP_CHAINMODE_AES_ECB) |
| { |
| if (CRYP_SetInitVector(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| } |
| } |
| |
| #if defined(AES_CR_NPBLB) |
| /* Clear NPBLB field */ |
| CLEAR_BIT(hcryp->Instance->CR, AES_CR_NPBLB); |
| #endif |
| |
| /* Reset CrypInCount and CrypOutCount */ |
| hcryp->CrypInCount = 0; |
| hcryp->CrypOutCount = 0; |
| |
| /* Reset ErrorCode field */ |
| hcryp->ErrorCode = HAL_CRYP_ERROR_NONE; |
| |
| /* Reset Mode suspension request */ |
| hcryp->SuspendRequest = HAL_CRYP_SUSPEND_NONE; |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| |
| /* Enable the Peripheral */ |
| __HAL_CRYP_ENABLE(); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief DeInitialize the CRYP peripheral. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_DeInit(CRYP_HandleTypeDef *hcryp) |
| { |
| /* Check the CRYP handle allocation */ |
| if(hcryp == NULL) |
| { |
| return HAL_ERROR; |
| } |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_BUSY; |
| |
| /* Set the default CRYP phase */ |
| hcryp->Phase = HAL_CRYP_PHASE_READY; |
| |
| /* Reset CrypInCount and CrypOutCount */ |
| hcryp->CrypInCount = 0; |
| hcryp->CrypOutCount = 0; |
| |
| /* Disable the CRYP Peripheral Clock */ |
| __HAL_CRYP_DISABLE(); |
| |
| /* DeInit the low level hardware: CLOCK, NVIC.*/ |
| HAL_CRYP_MspDeInit(hcryp); |
| |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_RESET; |
| |
| /* Release Lock */ |
| __HAL_UNLOCK(hcryp); |
| |
| /* Return function status */ |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Initialize the CRYP MSP. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @retval None |
| */ |
| __weak void HAL_CRYP_MspInit(CRYP_HandleTypeDef *hcryp) |
| { |
| /* Prevent unused argument(s) compilation warning */ |
| UNUSED(hcryp); |
| |
| /* NOTE : This function should not be modified; when the callback is needed, |
| the HAL_CRYP_MspInit can be implemented in the user file |
| */ |
| } |
| |
| /** |
| * @brief DeInitialize CRYP MSP. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @retval None |
| */ |
| __weak void HAL_CRYP_MspDeInit(CRYP_HandleTypeDef *hcryp) |
| { |
| /* Prevent unused argument(s) compilation warning */ |
| UNUSED(hcryp); |
| |
| /* NOTE : This function should not be modified; when the callback is needed, |
| the HAL_CRYP_MspDeInit can be implemented in the user file |
| */ |
| } |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup CRYP_Exported_Functions_Group2 AES processing functions |
| * @brief Processing functions. |
| * |
| @verbatim |
| ============================================================================== |
| ##### AES processing functions ##### |
| ============================================================================== |
| [..] This section provides functions allowing to: |
| (+) Encrypt plaintext using AES algorithm in different chaining modes |
| (+) Decrypt cyphertext using AES algorithm in different chaining modes |
| [..] Three processing functions are available: |
| (+) Polling mode |
| (+) Interrupt mode |
| (+) DMA mode |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| |
| /** |
| * @brief Encrypt pPlainData in AES ECB encryption mode. The cypher data are available in pCypherData. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Timeout Specify Timeout value |
| * @note This API is provided only to maintain compatibility with legacy software. Users should directly |
| * resort to generic HAL_CRYPEx_AES() API instead (usage recommended). |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESECB_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout) |
| { |
| /* Re-initialize AES IP with proper parameters */ |
| if (HAL_CRYP_DeInit(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| hcryp->Init.OperatingMode = CRYP_ALGOMODE_ENCRYPT; |
| hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_ECB; |
| hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; |
| if (HAL_CRYP_Init(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| |
| return HAL_CRYPEx_AES(hcryp, pPlainData, Size, pCypherData, Timeout); |
| } |
| |
| |
| /** |
| * @brief Encrypt pPlainData in AES CBC encryption mode with key derivation. The cypher data are available in pCypherData. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Timeout Specify Timeout value |
| * @note This API is provided only to maintain compatibility with legacy software. Users should directly |
| * resort to generic HAL_CRYPEx_AES() API instead (usage recommended). |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESCBC_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout) |
| { |
| /* Re-initialize AES IP with proper parameters */ |
| if (HAL_CRYP_DeInit(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| hcryp->Init.OperatingMode = CRYP_ALGOMODE_ENCRYPT; |
| hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CBC; |
| hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; |
| if (HAL_CRYP_Init(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| |
| return HAL_CRYPEx_AES(hcryp, pPlainData, Size, pCypherData, Timeout); |
| } |
| |
| |
| /** |
| * @brief Encrypt pPlainData in AES CTR encryption mode. The cypher data are available in pCypherData |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Timeout Specify Timeout value |
| * @note This API is provided only to maintain compatibility with legacy software. Users should directly |
| * resort to generic HAL_CRYPEx_AES() API instead (usage recommended). |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESCTR_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout) |
| { |
| /* Re-initialize AES IP with proper parameters */ |
| if (HAL_CRYP_DeInit(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| hcryp->Init.OperatingMode = CRYP_ALGOMODE_ENCRYPT; |
| hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CTR; |
| hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; |
| if (HAL_CRYP_Init(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| |
| return HAL_CRYPEx_AES(hcryp, pPlainData, Size, pCypherData, Timeout); |
| } |
| |
| /** |
| * @brief Decrypt pCypherData in AES ECB decryption mode with key derivation, |
| * the decyphered data are available in pPlainData. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Timeout Specify Timeout value |
| * @note This API is provided only to maintain compatibility with legacy software. Users should directly |
| * resort to generic HAL_CRYPEx_AES() API instead (usage recommended). |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESECB_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout) |
| { |
| /* Re-initialize AES IP with proper parameters */ |
| if (HAL_CRYP_DeInit(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| hcryp->Init.OperatingMode = CRYP_ALGOMODE_KEYDERIVATION_DECRYPT; |
| hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_ECB; |
| hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; |
| if (HAL_CRYP_Init(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| |
| return HAL_CRYPEx_AES(hcryp, pCypherData, Size, pPlainData, Timeout); |
| } |
| |
| /** |
| * @brief Decrypt pCypherData in AES ECB decryption mode with key derivation, |
| * the decyphered data are available in pPlainData. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Timeout Specify Timeout value |
| * @note This API is provided only to maintain compatibility with legacy software. Users should directly |
| * resort to generic HAL_CRYPEx_AES() API instead (usage recommended). |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESCBC_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout) |
| { |
| /* Re-initialize AES IP with proper parameters */ |
| if (HAL_CRYP_DeInit(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| hcryp->Init.OperatingMode = CRYP_ALGOMODE_KEYDERIVATION_DECRYPT; |
| hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CBC; |
| hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; |
| if (HAL_CRYP_Init(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| |
| return HAL_CRYPEx_AES(hcryp, pCypherData, Size, pPlainData, Timeout); |
| } |
| |
| /** |
| * @brief Decrypt pCypherData in AES CTR decryption mode, |
| * the decyphered data are available in pPlainData. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Timeout Specify Timeout value |
| * @note This API is provided only to maintain compatibility with legacy software. Users should directly |
| * resort to generic HAL_CRYPEx_AES() API instead (usage recommended). |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESCTR_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout) |
| { |
| /* Re-initialize AES IP with proper parameters */ |
| if (HAL_CRYP_DeInit(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| hcryp->Init.OperatingMode = CRYP_ALGOMODE_DECRYPT; |
| hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CTR; |
| hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; |
| if (HAL_CRYP_Init(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| |
| return HAL_CRYPEx_AES(hcryp, pCypherData, Size, pPlainData, Timeout); |
| } |
| |
| /** |
| * @brief Encrypt pPlainData in AES ECB encryption mode using Interrupt, |
| * the cypher data are available in pCypherData. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @note This API is provided only to maintain compatibility with legacy software. Users should directly |
| * resort to generic HAL_CRYPEx_AES_IT() API instead (usage recommended). |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESECB_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) |
| { |
| /* Re-initialize AES IP with proper parameters */ |
| if (HAL_CRYP_DeInit(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| hcryp->Init.OperatingMode = CRYP_ALGOMODE_ENCRYPT; |
| hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_ECB; |
| hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; |
| if (HAL_CRYP_Init(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| |
| return HAL_CRYPEx_AES_IT(hcryp, pPlainData, Size, pCypherData); |
| } |
| |
| /** |
| * @brief Encrypt pPlainData in AES CBC encryption mode using Interrupt, |
| * the cypher data are available in pCypherData. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @note This API is provided only to maintain compatibility with legacy software. Users should directly |
| * resort to generic HAL_CRYPEx_AES_IT() API instead (usage recommended). |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESCBC_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) |
| { |
| /* Re-initialize AES IP with proper parameters */ |
| if (HAL_CRYP_DeInit(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| hcryp->Init.OperatingMode = CRYP_ALGOMODE_ENCRYPT; |
| hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CBC; |
| hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; |
| if (HAL_CRYP_Init(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| |
| return HAL_CRYPEx_AES_IT(hcryp, pPlainData, Size, pCypherData); |
| } |
| |
| |
| /** |
| * @brief Encrypt pPlainData in AES CTR encryption mode using Interrupt, |
| * the cypher data are available in pCypherData. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @note This API is provided only to maintain compatibility with legacy software. Users should directly |
| * resort to generic HAL_CRYPEx_AES_IT() API instead (usage recommended). |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESCTR_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) |
| { |
| /* Re-initialize AES IP with proper parameters */ |
| if (HAL_CRYP_DeInit(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| hcryp->Init.OperatingMode = CRYP_ALGOMODE_ENCRYPT; |
| hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CTR; |
| hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; |
| if (HAL_CRYP_Init(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| |
| return HAL_CRYPEx_AES_IT(hcryp, pPlainData, Size, pCypherData); |
| } |
| |
| /** |
| * @brief Decrypt pCypherData in AES ECB decryption mode using Interrupt, |
| * the decyphered data are available in pPlainData. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. |
| * @param pPlainData Pointer to the plaintext buffer. |
| * @note This API is provided only to maintain compatibility with legacy software. Users should directly |
| * resort to generic HAL_CRYPEx_AES_IT() API instead (usage recommended). |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESECB_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) |
| { |
| /* Re-initialize AES IP with proper parameters */ |
| if (HAL_CRYP_DeInit(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| hcryp->Init.OperatingMode = CRYP_ALGOMODE_KEYDERIVATION_DECRYPT; |
| hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_ECB; |
| hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; |
| if (HAL_CRYP_Init(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| |
| return HAL_CRYPEx_AES_IT(hcryp, pCypherData, Size, pPlainData); |
| } |
| |
| /** |
| * @brief Decrypt pCypherData in AES CBC decryption mode using Interrupt, |
| * the decyphered data are available in pPlainData. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. |
| * @param pPlainData Pointer to the plaintext buffer |
| * @note This API is provided only to maintain compatibility with legacy software. Users should directly |
| * resort to generic HAL_CRYPEx_AES_IT() API instead (usage recommended). |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESCBC_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) |
| { |
| /* Re-initialize AES IP with proper parameters */ |
| if (HAL_CRYP_DeInit(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| hcryp->Init.OperatingMode = CRYP_ALGOMODE_KEYDERIVATION_DECRYPT; |
| hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CBC; |
| hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; |
| if (HAL_CRYP_Init(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| |
| return HAL_CRYPEx_AES_IT(hcryp, pCypherData, Size, pPlainData); |
| } |
| |
| /** |
| * @brief Decrypt pCypherData in AES CTR decryption mode using Interrupt, |
| * the decyphered data are available in pPlainData. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. |
| * @param pPlainData Pointer to the plaintext buffer |
| * @note This API is provided only to maintain compatibility with legacy software. Users should directly |
| * resort to generic HAL_CRYPEx_AES_IT() API instead (usage recommended). |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESCTR_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) |
| { |
| /* Re-initialize AES IP with proper parameters */ |
| if (HAL_CRYP_DeInit(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| hcryp->Init.OperatingMode = CRYP_ALGOMODE_DECRYPT; |
| hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CTR; |
| hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; |
| if (HAL_CRYP_Init(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| |
| return HAL_CRYPEx_AES_IT(hcryp, pCypherData, Size, pPlainData); |
| } |
| |
| /** |
| * @brief Encrypt pPlainData in AES ECB encryption mode using DMA, |
| * the cypher data are available in pCypherData. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @note This API is provided only to maintain compatibility with legacy software. Users should directly |
| * resort to generic HAL_CRYPEx_AES_DMA() API instead (usage recommended). |
| * @note pPlainData and pCypherData buffers must be 32-bit aligned to ensure a correct DMA transfer to and from the IP. |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESECB_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) |
| { |
| /* Re-initialize AES IP with proper parameters */ |
| if (HAL_CRYP_DeInit(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| hcryp->Init.OperatingMode = CRYP_ALGOMODE_ENCRYPT; |
| hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_ECB; |
| hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; |
| if (HAL_CRYP_Init(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| |
| return HAL_CRYPEx_AES_DMA(hcryp, pPlainData, Size, pCypherData); |
| } |
| |
| |
| |
| /** |
| * @brief Encrypt pPlainData in AES CBC encryption mode using DMA, |
| * the cypher data are available in pCypherData. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer, must be a multiple of 16. |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @note This API is provided only to maintain compatibility with legacy software. Users should directly |
| * resort to generic HAL_CRYPEx_AES_DMA() API instead (usage recommended). |
| * @note pPlainData and pCypherData buffers must be 32-bit aligned to ensure a correct DMA transfer to and from the IP. |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESCBC_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) |
| { |
| /* Re-initialize AES IP with proper parameters */ |
| if (HAL_CRYP_DeInit(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| hcryp->Init.OperatingMode = CRYP_ALGOMODE_ENCRYPT; |
| hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CBC; |
| hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; |
| if (HAL_CRYP_Init(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| |
| return HAL_CRYPEx_AES_DMA(hcryp, pPlainData, Size, pCypherData); |
| } |
| |
| /** |
| * @brief Encrypt pPlainData in AES CTR encryption mode using DMA, |
| * the cypher data are available in pCypherData. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pPlainData Pointer to the plaintext buffer |
| * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. |
| * @param pCypherData Pointer to the cyphertext buffer. |
| * @note This API is provided only to maintain compatibility with legacy software. Users should directly |
| * resort to generic HAL_CRYPEx_AES_DMA() API instead (usage recommended). |
| * @note pPlainData and pCypherData buffers must be 32-bit aligned to ensure a correct DMA transfer to and from the IP. |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESCTR_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) |
| { |
| /* Re-initialize AES IP with proper parameters */ |
| if (HAL_CRYP_DeInit(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| hcryp->Init.OperatingMode = CRYP_ALGOMODE_ENCRYPT; |
| hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CTR; |
| hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; |
| if (HAL_CRYP_Init(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| |
| return HAL_CRYPEx_AES_DMA(hcryp, pPlainData, Size, pCypherData); |
| } |
| |
| /** |
| * @brief Decrypt pCypherData in AES ECB decryption mode using DMA, |
| * the decyphered data are available in pPlainData. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. |
| * @param pPlainData Pointer to the plaintext buffer |
| * @note This API is provided only to maintain compatibility with legacy software. Users should directly |
| * resort to generic HAL_CRYPEx_AES_DMA() API instead (usage recommended). |
| * @note pPlainData and pCypherData buffers must be 32-bit aligned to ensure a correct DMA transfer to and from the IP. |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESECB_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) |
| { |
| /* Re-initialize AES IP with proper parameters */ |
| if (HAL_CRYP_DeInit(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| hcryp->Init.OperatingMode = CRYP_ALGOMODE_KEYDERIVATION_DECRYPT; |
| hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_ECB; |
| hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; |
| if (HAL_CRYP_Init(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| |
| return HAL_CRYPEx_AES_DMA(hcryp, pCypherData, Size, pPlainData); |
| } |
| |
| /** |
| * @brief Decrypt pCypherData in AES CBC decryption mode using DMA, |
| * the decyphered data are available in pPlainData. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. |
| * @param pPlainData Pointer to the plaintext buffer |
| * @note This API is provided only to maintain compatibility with legacy software. Users should directly |
| * resort to generic HAL_CRYPEx_AES_DMA() API instead (usage recommended). |
| * @note pPlainData and pCypherData buffers must be 32-bit aligned to ensure a correct DMA transfer to and from the IP. |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESCBC_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) |
| { |
| /* Re-initialize AES IP with proper parameters */ |
| if (HAL_CRYP_DeInit(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| hcryp->Init.OperatingMode = CRYP_ALGOMODE_KEYDERIVATION_DECRYPT; |
| hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CBC; |
| hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; |
| if (HAL_CRYP_Init(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| |
| return HAL_CRYPEx_AES_DMA(hcryp, pCypherData, Size, pPlainData); |
| } |
| |
| /** |
| * @brief Decrypt pCypherData in AES CTR decryption mode using DMA, |
| * the decyphered data are available in pPlainData. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @param pCypherData Pointer to the cyphertext buffer |
| * @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. |
| * @param pPlainData Pointer to the plaintext buffer |
| * @note This API is provided only to maintain compatibility with legacy software. Users should directly |
| * resort to generic HAL_CRYPEx_AES_DMA() API instead (usage recommended). |
| * @note pPlainData and pCypherData buffers must be 32-bit aligned to ensure a correct DMA transfer to and from the IP. |
| * @retval HAL status |
| */ |
| HAL_StatusTypeDef HAL_CRYP_AESCTR_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) |
| { |
| /* Re-initialize AES IP with proper parameters */ |
| if (HAL_CRYP_DeInit(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| hcryp->Init.OperatingMode = CRYP_ALGOMODE_DECRYPT; |
| hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CTR; |
| hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; |
| if (HAL_CRYP_Init(hcryp) != HAL_OK) |
| { |
| return HAL_ERROR; |
| } |
| |
| return HAL_CRYPEx_AES_DMA(hcryp, pCypherData, Size, pPlainData); |
| } |
| |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup CRYP_Exported_Functions_Group3 Callback functions |
| * @brief Callback functions. |
| * |
| @verbatim |
| ============================================================================== |
| ##### Callback functions ##### |
| ============================================================================== |
| [..] This section provides Interruption and DMA callback functions: |
| (+) DMA Input data transfer complete |
| (+) DMA Output data transfer complete |
| (+) DMA or Interrupt error |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief CRYP error callback. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @retval None |
| */ |
| __weak void HAL_CRYP_ErrorCallback(CRYP_HandleTypeDef *hcryp) |
| { |
| /* Prevent unused argument(s) compilation warning */ |
| UNUSED(hcryp); |
| |
| /* NOTE : This function should not be modified; when the callback is needed, |
| the HAL_CRYP_ErrorCallback can be implemented in the user file |
| */ |
| } |
| |
| /** |
| * @brief Input DMA transfer complete callback. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @retval None |
| */ |
| __weak void HAL_CRYP_InCpltCallback(CRYP_HandleTypeDef *hcryp) |
| { |
| /* Prevent unused argument(s) compilation warning */ |
| UNUSED(hcryp); |
| |
| /* NOTE : This function should not be modified; when the callback is needed, |
| the HAL_CRYP_InCpltCallback can be implemented in the user file |
| */ |
| } |
| |
| /** |
| * @brief Output DMA transfer complete callback. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @retval None |
| */ |
| __weak void HAL_CRYP_OutCpltCallback(CRYP_HandleTypeDef *hcryp) |
| { |
| /* Prevent unused argument(s) compilation warning */ |
| UNUSED(hcryp); |
| |
| /* NOTE : This function should not be modified; when the callback is needed, |
| the HAL_CRYP_OutCpltCallback can be implemented in the user file |
| */ |
| } |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup CRYP_Exported_Functions_Group4 CRYP IRQ handler |
| * @brief AES IRQ handler. |
| * |
| @verbatim |
| ============================================================================== |
| ##### AES IRQ handler management ##### |
| ============================================================================== |
| [..] This section provides AES IRQ handler function. |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief Handle AES interrupt request. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @retval None |
| */ |
| void HAL_CRYP_IRQHandler(CRYP_HandleTypeDef *hcryp) |
| { |
| /* Check if error occurred */ |
| if (__HAL_CRYP_GET_IT_SOURCE(CRYP_IT_ERRIE) != RESET) |
| { |
| /* If Write Error occurred */ |
| if (__HAL_CRYP_GET_FLAG(CRYP_IT_WRERR) != RESET) |
| { |
| hcryp->ErrorCode |= HAL_CRYP_WRITE_ERROR; |
| hcryp->State = HAL_CRYP_STATE_ERROR; |
| } |
| /* If Read Error occurred */ |
| if (__HAL_CRYP_GET_FLAG(CRYP_IT_RDERR) != RESET) |
| { |
| hcryp->ErrorCode |= HAL_CRYP_READ_ERROR; |
| hcryp->State = HAL_CRYP_STATE_ERROR; |
| } |
| |
| /* If an error has been reported */ |
| if (hcryp->State == HAL_CRYP_STATE_ERROR) |
| { |
| /* Disable Error and Computation Complete Interrupts */ |
| __HAL_CRYP_DISABLE_IT(CRYP_IT_CCFIE|CRYP_IT_ERRIE); |
| /* Clear all Interrupt flags */ |
| __HAL_CRYP_CLEAR_FLAG(CRYP_ERR_CLEAR|CRYP_CCF_CLEAR); |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| HAL_CRYP_ErrorCallback(hcryp); |
| |
| return; |
| } |
| } |
| |
| /* Check if computation complete interrupt is enabled |
| and if the computation complete flag is raised */ |
| if((__HAL_CRYP_GET_FLAG(CRYP_IT_CCF) != RESET) && (__HAL_CRYP_GET_IT_SOURCE(CRYP_IT_CCFIE) != RESET)) |
| { |
| #if defined(AES_CR_NPBLB) |
| if ((hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_GCM_GMAC) |
| || (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CCM_CMAC)) |
| #else |
| if ((hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_GCM_GMAC) |
| || (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CMAC)) |
| #endif |
| { |
| /* To ensure proper suspension requests management, CCF flag |
| is reset in CRYP_AES_Auth_IT() according to the current |
| phase under handling */ |
| CRYP_AES_Auth_IT(hcryp); |
| } |
| else |
| { |
| /* Clear Computation Complete Flag */ |
| __HAL_CRYP_CLEAR_FLAG(CRYP_CCF_CLEAR); |
| CRYP_AES_IT(hcryp); |
| } |
| } |
| } |
| |
| /** |
| * @} |
| */ |
| |
| /** @defgroup CRYP_Exported_Functions_Group5 Peripheral State functions |
| * @brief Peripheral State functions. |
| * |
| @verbatim |
| ============================================================================== |
| ##### Peripheral State functions ##### |
| ============================================================================== |
| [..] |
| This subsection permits to get in run-time the status of the peripheral. |
| |
| @endverbatim |
| * @{ |
| */ |
| |
| /** |
| * @brief Return the CRYP handle state. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @retval HAL state |
| */ |
| HAL_CRYP_STATETypeDef HAL_CRYP_GetState(CRYP_HandleTypeDef *hcryp) |
| { |
| /* Return CRYP handle state */ |
| return hcryp->State; |
| } |
| |
| /** |
| * @brief Return the CRYP peripheral error. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @note The returned error is a bit-map combination of possible errors |
| * @retval Error bit-map |
| */ |
| uint32_t HAL_CRYP_GetError(CRYP_HandleTypeDef *hcryp) |
| { |
| return hcryp->ErrorCode; |
| } |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| /** @addtogroup CRYP_Private_Functions |
| * @{ |
| */ |
| |
| |
| /** |
| * @brief Write the Key in KeyRx registers. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @retval None |
| */ |
| static HAL_StatusTypeDef CRYP_SetKey(CRYP_HandleTypeDef *hcryp) |
| { |
| uint32_t keyaddr = 0x0; |
| |
| if ((uint32_t)(hcryp->Init.pKey == NULL)) |
| { |
| return HAL_ERROR; |
| } |
| |
| |
| keyaddr = (uint32_t)(hcryp->Init.pKey); |
| |
| if (hcryp->Init.KeySize == CRYP_KEYSIZE_256B) |
| { |
| hcryp->Instance->KEYR7 = __REV(*(uint32_t*)(keyaddr)); |
| keyaddr+=4; |
| hcryp->Instance->KEYR6 = __REV(*(uint32_t*)(keyaddr)); |
| keyaddr+=4; |
| hcryp->Instance->KEYR5 = __REV(*(uint32_t*)(keyaddr)); |
| keyaddr+=4; |
| hcryp->Instance->KEYR4 = __REV(*(uint32_t*)(keyaddr)); |
| keyaddr+=4; |
| } |
| |
| hcryp->Instance->KEYR3 = __REV(*(uint32_t*)(keyaddr)); |
| keyaddr+=4; |
| hcryp->Instance->KEYR2 = __REV(*(uint32_t*)(keyaddr)); |
| keyaddr+=4; |
| hcryp->Instance->KEYR1 = __REV(*(uint32_t*)(keyaddr)); |
| keyaddr+=4; |
| hcryp->Instance->KEYR0 = __REV(*(uint32_t*)(keyaddr)); |
| |
| return HAL_OK; |
| } |
| |
| /** |
| * @brief Write the InitVector/InitCounter in IVRx registers. |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module |
| * @retval None |
| */ |
| static HAL_StatusTypeDef CRYP_SetInitVector(CRYP_HandleTypeDef *hcryp) |
| { |
| uint32_t ivaddr = 0x0; |
| |
| #if !defined(AES_CR_NPBLB) |
| if (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CMAC) |
| { |
| hcryp->Instance->IVR3 = 0; |
| hcryp->Instance->IVR2 = 0; |
| hcryp->Instance->IVR1 = 0; |
| hcryp->Instance->IVR0 = 0; |
| } |
| else |
| #endif |
| { |
| if (hcryp->Init.pInitVect == NULL) |
| { |
| return HAL_ERROR; |
| } |
| |
| ivaddr = (uint32_t)(hcryp->Init.pInitVect); |
| |
| hcryp->Instance->IVR3 = __REV(*(uint32_t*)(ivaddr)); |
| ivaddr+=4; |
| hcryp->Instance->IVR2 = __REV(*(uint32_t*)(ivaddr)); |
| ivaddr+=4; |
| hcryp->Instance->IVR1 = __REV(*(uint32_t*)(ivaddr)); |
| ivaddr+=4; |
| hcryp->Instance->IVR0 = __REV(*(uint32_t*)(ivaddr)); |
| } |
| return HAL_OK; |
| } |
| |
| |
| |
| /** |
| * @brief Handle CRYP block input/output data handling under interruption. |
| * @note The function is called under interruption only, once |
| * interruptions have been enabled by HAL_CRYPEx_AES_IT(). |
| * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains |
| * the configuration information for CRYP module. |
| * @retval HAL status |
| */ |
| static HAL_StatusTypeDef CRYP_AES_IT(CRYP_HandleTypeDef *hcryp) |
| { |
| uint32_t inputaddr = 0; |
| uint32_t outputaddr = 0; |
| |
| if(hcryp->State == HAL_CRYP_STATE_BUSY) |
| { |
| if (hcryp->Init.OperatingMode != CRYP_ALGOMODE_KEYDERIVATION) |
| { |
| /* Get the output data address */ |
| outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; |
| |
| /* Read the last available output block from the Data Output Register */ |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUTR; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUTR; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUTR; |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = hcryp->Instance->DOUTR; |
| hcryp->pCrypOutBuffPtr += 16; |
| hcryp->CrypOutCount -= 16; |
| |
| } |
| else |
| { |
| /* Read the derived key from the Key registers */ |
| if (hcryp->Init.KeySize == CRYP_KEYSIZE_256B) |
| { |
| *(uint32_t*)(outputaddr) = __REV(hcryp->Instance->KEYR7); |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = __REV(hcryp->Instance->KEYR6); |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = __REV(hcryp->Instance->KEYR5); |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = __REV(hcryp->Instance->KEYR4); |
| outputaddr+=4; |
| } |
| |
| *(uint32_t*)(outputaddr) = __REV(hcryp->Instance->KEYR3); |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = __REV(hcryp->Instance->KEYR2); |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = __REV(hcryp->Instance->KEYR1); |
| outputaddr+=4; |
| *(uint32_t*)(outputaddr) = __REV(hcryp->Instance->KEYR0); |
| } |
| |
| /* In case of ciphering or deciphering, check if all output text has been retrieved; |
| In case of key derivation, stop right there */ |
| if ((hcryp->CrypOutCount == 0) || (hcryp->Init.OperatingMode == CRYP_ALGOMODE_KEYDERIVATION)) |
| { |
| /* Disable Computation Complete Flag and Errors Interrupts */ |
| __HAL_CRYP_DISABLE_IT(CRYP_IT_CCFIE|CRYP_IT_ERRIE); |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_READY; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| /* Call computation complete callback */ |
| HAL_CRYPEx_ComputationCpltCallback(hcryp); |
| |
| return HAL_OK; |
| } |
| /* If suspension flag has been raised, suspend processing */ |
| else if (hcryp->SuspendRequest == HAL_CRYP_SUSPEND) |
| { |
| /* reset ModeSuspend */ |
| hcryp->SuspendRequest = HAL_CRYP_SUSPEND_NONE; |
| |
| /* Disable Computation Complete Flag and Errors Interrupts */ |
| __HAL_CRYP_DISABLE_IT(CRYP_IT_CCFIE|CRYP_IT_ERRIE); |
| /* Change the CRYP state */ |
| hcryp->State = HAL_CRYP_STATE_SUSPENDED; |
| |
| /* Process Unlocked */ |
| __HAL_UNLOCK(hcryp); |
| |
| return HAL_OK; |
| } |
| else /* Process the rest of input data */ |
| { |
| /* Get the Intput data address */ |
| inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; |
| |
| /* Increment/decrement instance pointer/counter */ |
| hcryp->pCrypInBuffPtr += 16; |
| hcryp->CrypInCount -= 16; |
| |
| /* Write the next input block in the Data Input register */ |
| hcryp->Instance->DINR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DINR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DINR = *(uint32_t*)(inputaddr); |
| inputaddr+=4; |
| hcryp->Instance->DINR = *(uint32_t*)(inputaddr); |
| |
| return HAL_OK; |
| } |
| } |
| else |
| { |
| return HAL_BUSY; |
| } |
| } |
| |
| |
| |
| |
| /** |
| * @} |
| */ |
| |
| |
| |
| /** |
| * @} |
| */ |
| |
| /** |
| * @} |
| */ |
| |
| #endif /* AES */ |
| |
| #endif /* HAL_CRYP_MODULE_ENABLED */ |
| |
| /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |