# Licensed to the Apache Software Foundation (ASF) under one
# or more contributor license agreements.  See the NOTICE file
# distributed with this work for additional information
# regarding copyright ownership.  The ASF licenses this file
# to you under the Apache License, Version 2.0 (the
# "License"); you may not use this file except in compliance
# with the License.  You may obtain a copy of the License at
#
#  http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing,
# software distributed under the License is distributed on an
# "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY
# KIND, either express or implied.  See the License for the
# specific language governing permissions and limitations
# under the License.
#

syscfg.defs:
    MCU_FLASH_MIN_WRITE_SIZE:
        description: >
            Specifies the required alignment for internal flash writes.
            Used internally by the newt tool.
        value: 4
    I2C_0:
        description: 'I2C interface 0'
        value:  0
    I2C_0_FREQ_KHZ:
        description: 'Frequency in khz for I2C_0 bus'
        value:  100
    I2C_1:
        description: 'I2C interface 1'
        value:  0
    I2C_1_FREQ_KHZ:
        description: 'Frequency in khz for I2C_0 bus'
        value:  100
    I2C_2:
        description: 'I2C interface 2'
        value:  0
    I2C_2_FREQ_KHZ:
        description: 'Frequency in khz for I2C_0 bus'
        value:  100
    I2C_3:
        description: 'I2C interface 3'
        value:  0
    I2C_3_FREQ_KHZ:
        description: 'Frequency in khz for I2C_0 bus'
        value:  100
    I2C_4:
        description: 'I2C interface 4'
        value:  0
    I2C_4_FREQ_KHZ:
        description: 'Frequency in khz for I2C_0 bus'
        value:  100

    SPI_0_MASTER:
        description: 'SPI 0 master'
        value:  0
    SPI_0_MASTER_PIN_MOSI:
        description: 'MOSI pin for SPI_0_MASTER'
        value: 0xFF
    SPI_0_MASTER_PIN_MISO:
        description: 'MOSI pin for SPI_0_MASTER'
        value: 0xFF
    SPI_1_MASTER:
        description: 'SPI 1 master'
        value:  0
    SPI_1_MASTER_PIN_MOSI:
        description: 'MOSI pin for SPI_1_MASTER'
        value: 0xFF
    SPI_1_MASTER_PIN_MISO:
        description: 'MOSI pin for SPI_1_MASTER'
        value: 0xFF
    SPI_2_MASTER:
        description: 'SPI 2 master'
        value:  0
    SPI_2_MASTER_PIN_MOSI:
        description: 'MOSI pin for SPI_2_MASTER'
        value: 0xFF
    SPI_2_MASTER_PIN_MISO:
        description: 'MOSI pin for SPI_2_MASTER'
        value: 0xFF
    SPI_3_MASTER:
        description: 'SPI 3 master'
        value:  0
    SPI_3_MASTER_PIN_MOSI:
        description: 'MOSI pin for SPI_3_MASTER'
        value: 0xFF
    SPI_3_MASTER_PIN_MISO:
        description: 'MOSI pin for SPI_3_MASTER'
        value: 0xFF
    SPI_4_MASTER:
        description: 'SPI 4 master'
        value:  0
    SPI_4_MASTER_PIN_MOSI:
        description: 'MOSI pin for SPI_4_MASTER'
        value: 0xFF
    SPI_4_MASTER_PIN_MISO:
        description: 'MOSI pin for SPI_4_MASTER'
        value: 0xFF
    SPI_5_MASTER:
        description: 'SPI 5 master'
        value:  0
    SPI_5_MASTER_PIN_MOSI:
        description: 'MOSI pin for SPI_5_MASTER'
        value: 0xFF
    SPI_5_MASTER_PIN_MISO:
        description: 'MOSI pin for SPI_5_MASTER'
        value: 0xFF

    UART_0:
        description: Enable UART_0 (Datasheet peripheral name UART1)
        value: 0
    UART_0_PIN_TX:
        description: 'TX pin for UART_0'
        value: 0xFF
    UART_0_PIN_RX:
        description: 'RX pin for UART_0'
        value: 0xFF
    UART_0_PIN_RTS:
        description: 'RTS pin for UART_0'
        value: 0xFF
    UART_0_PIN_CTS:
        description: 'CTS pin for UART_0'
        value: 0xFF

    UART_1:
        description: Enable UART_1 (Datasheet peripheral name UART2)
        value: 0
    UART_1_PIN_TX:
        description: 'TX pin for UART_1'
        value: 0xFF
    UART_1_PIN_RX:
        description: 'RX pin for UART_1'
        value: 0xFF
    UART_1_PIN_RTS:
        description: 'RTS pin for UART_1'
        value: 0xFF
    UART_1_PIN_CTS:
        description: 'CTS pin for UART_1'
        value: 0xFF

    UART_2:
        description: Enable UART_2 (Datasheet peripheral name UART3)
        value: 0
    UART_2_PIN_TX:
        description: 'TX pin for UART_2'
        value: 0xFF
    UART_2_PIN_RX:
        description: 'RX pin for UART_2'
        value: 0xFF
    UART_2_PIN_RTS:
        description: 'RTS pin for UART_2'
        value: 0xFF
    UART_2_PIN_CTS:
        description: 'CTS pin for UART_2'
        value: 0xFF

    UART_3:
        description: Enable UART_4 (Datasheet peripheral name UART4)
        value: 0
    UART_3_PIN_TX:
        description: 'TX pin for UART_3'
        value: 0xFF
    UART_3_PIN_RX:
        description: 'RX pin for UART_3'
        value: 0xFF
    UART_3_PIN_RTS:
        description: 'RTS pin for UART_3'
        value: 0xFF
    UART_3_PIN_CTS:
        description: 'CTS pin for UART_3'
        value: 0xFF

    UART_4:
        description: Enable UART_4 (Datasheet peripheral name UART5)
        value: 0
    UART_4_PIN_TX:
        description: 'TX pin for UART_4'
        value: 0xFF
    UART_4_PIN_RX:
        description: 'RX pin for UART_4'
        value: 0xFF
    UART_4_PIN_RTS:
        description: 'RTS pin for UART_4'
        value: 0xFF
    UART_4_PIN_CTS:
        description: 'CTS pin for UART_4'
        value: 0xFF

    UART_5:
        description: Enable UART_5 (Datasheet peripheral name UART6)
        value: 0
    UART_5_PIN_TX:
        description: 'TX pin for UART_5'
        value: 0xFF
    UART_5_PIN_RX:
        description: 'RX pin for UART_5'
        value: 0xFF
    UART_5_PIN_RTS:
        description: 'RTS pin for UART_5'
        value: 0xFF
    UART_5_PIN_CTS:
        description: 'CTS pin for UART_5'
        value: 0xFF

    TIMER_0:
        description: "Whether to enable Timer 0"
        value:  1

    TIMER_1:
        description: "Whether to enable Timer 1"
        value:  0

    TIMER_2:
        description: "Whether to enable Timer 2"
        value:  0

    TIMER_3:
        description: "Whether to enable Timer 3"
        value:  0

    TIMER_4:
        description: "Whether to enable Timer 4"
        value:  0

    TIMER_5:
        description: "Whether to enable Timer 5"
        value:  0

    TIMER_6:
        description: "Whether to enable Timer 6"
        value:  0

    TIMER_7:
        description: "Whether to enable Timer 7"
        value:  0

    SYSTEM_CLOCK_OSC_FREQ:
        descriprion: HS Oscilator/External clock freqency.
        value:
    SYSTEM_CLOCK_SRC:
        description: >
            Select system clock source, that will affect both CONFIG registers
            and startup code.
        value:
        choices:
            - FRC_DIV
            - FRC_PLL
            - POSC
            - POSC_PLL
    SYSTEM_CLOCK_FRC_DIV:
        description: FRCDIV value
        range: 1,2,4,6,8,16,32,64,256
        value: 1
    SYSTEM_CLOCK_PLLIDIV:
        description:
        range: 1..8
        value:
    SYSTEM_CLOCK_PLLRANGE:
        description:
        range: 1..5
        value:
    SYSTEM_CLOCK_PLLMULT:
        description:
        range: 1..128
        value:
    SYSTEM_CLOCK_PLLODIV:
        description:
        range: 2,4,8,16,32
        value:

    MCU_NO_BOOTLOADER_BUILD:
        description: >
            Set this value to 1 when building elf files that are not
            converted to img files.
        value: 0

syscfg.vals:
    OS_TICKS_PER_SEC: 1000