
                  Testing Apache with the Perl Test Harness
Prerequisites
-------------
These two modules must first be installed;

- perl-ExtUtils-MakeMaker 
- perl-Test 

You'll need to install the CPAN modules listed in:
Apache-Test/lib/Bundle/ApacheTest.pm
All you have to do to install them all in one shot is:
perl -MCPAN -e 'install Bundle::ApacheTest'

Which are also available in one tarball here:
http://perl.apache.org/~dougm/httpd-test-bundle-0.02.tar.gz

Note: Crypt::SSLeay requires OpenSSL to be installed (only required
for t/TEST -ssl): http://www.openssl.org/
More accurate results may be obtained by using the same openssl command
line and libraries as consumed by APR-util and mod_ssl, due to X509
formatting behavior differences.

For an extensive documentation see
http://perl.apache.org/docs/general/testing/testing.html
 or
http://svn.apache.org/viewvc/perl/modperl/docs/trunk/src/docs/general/testing/testing.pod

To run the tests for all Apache web server modules, some additional 
CPAN modules will be required. If the tests don't work, make sure
that you have up to date versions of each of these perl modules:
- HTTP::DAV (DAV tests)
- DateTime (mod_include tests)
- Time::HiRes
- Protocol::HTTP2::Client and AnyEvent (mod_http2 tests)
- Test
- Test::Harness
- Crypt::SSLeay
- Net::SSLeay
- IO::Socket::SSL
- IO::Socket::IP
- IO::Select
- LWP::Protocol::https

Quick Start 
----------- 

If you don't care how it works and just want to run the tests, here's
how you go about doing that.

1. You need an installation of Apache. (1.3.x thru trunk)
2. Any DSOs you wish to use should be configured in that Apache's
   httpd.conf (the test harness will pick this configuration up)
3. Setup:
   perl Makefile.PL -apxs /path/to/apache/bin/apxs
4. Run the tests:
   t/TEST
5. Evaluate test output.

Getting a little deeper
-----------------------

The test harness will run every .t file under the t/ directory.  So
let's say you only want to run the tests for PHP.  Do this:
    t/TEST -httpd /path/to/apache/bin/httpd t/php

That will start the test server, run the .t tests under t/php and shut
down the test server.  You can also control each of these steps.

This will start the test server:
    t/TEST -httpd /path/to/apache/bin/httpd -start

This will run the PHP tests in the test environment:
    t/TEST t/php

This will stop the test server:
    t/TEST -stop

This will run the server under gdb (using -X):
    t/TEST -d gdb

Note: At this point, you have a working test environment.  You can
look in t/conf for the test server configuration files.  These are
generated by the test harness.  Once you have a working test
environment, you do not need to specify 'httpd' on the t/TEST command
line.  For instance, to start the server up again, the command
    t/TEST -start
would be sufficient.

Running Regression Tests 
------------------------
For a full regression test, you should have all modules loaded. Build the server
with 
  configure --enable-modules=reallyall --enable-load-all-modules ...
among other things. Edit the generated httpd.conf and comment all mpm modules
that you do not want. Run "t/TEST -clean" again.

You will see some
  skipped: cannot find module 'XXX'
as not all modules are in every apache release (but the tests run for all).

All in all, some >4k tests will run and the result needs to be: PASS

Trouble Shooting
----------------
If you have a "PASS" at the end of "t/TEST", congratulations! If not, this
sections gives some advise in order to find the cause. Feel free to expand
this to make life easier for others.

0. If your test startup hangs forever in "waiting for server to warm up", but
   the test server is reachable under port 8529, you might be the victim of
   ipv4/6 confusion. The default servername configured is "localhost" and 
   some operating systems define 127.0.0.1 *as well as* ::1 in /etc/hosts.
   If the test server listens only on 0.0.0.0 it might not answer requests to 
   ::1 and that causes the test startup to hang.
   Solution: comment the ::1 line in /etc/hosts and see if that improves matters.
1. Run "t/TEST -clean" every time you change something in your Apache 
   configuration. The test suite picks up certain things from your installed
   httpd.conf (such as LoadModule statements) and will not see your changes
   unless you clean it.
2. Failures in proxy.t may originate from the fact that the test script cannot
   open the specified port. This happens on some machines if you abort a test
   run and the socket is not properly shut down. Check if the error goes
   away after a reboot. (proxy.t tests are slow, so chances you interrupt tests
   at that point are good.)
3. Failures in access.t may result from reverse lookups not working or giving
   other answers than expected. In the cause 0 above, if the test client
   connects via 127.0.0.1, a "Grant for localhost" might resolve to "::1"
   and therefore will not match the access rules of the tests.
   Solution: check that your servername is 'localhost' (which is
   the default) and that it *always* resolves to 127.0.0.1.
4. If some ssl test cases fail, especially when t/ssl/proxy.t fails, the
   reason can be mismatches between your installed SSL library and the one
   httpd uses. The "openssl" binary found in your $PATH is used to create
   binary setup files by t/TEST. If another version of openssl then tries
   to read these from your Apache server process, it might fail.
   Try the following:
      > t/TEST -clean
      > PATH=<bin dir of correct openssl>:$PATH t/TEST
   If a lot of ssl tests fail, check in the error log for the presence of
   a certificate validation error. If you find it, check the expiration date
   of the TLS/SSL certificates used by the tests, they might be expired.
   Running TEST -clean should delete the old ssl certificates, so they'll be
   regenerated during the next run.
5. If you see failures in the modules/h2.t test cases, please notify the dev
   mailing list with a description of your setup. These tests are quite young,
   currently only valid in 2.4.x and later and interact with quite some other
   modules as well as Openssl versions installed. Some tests require mod_ssl
   so make sure to load it in the httpd conf.
6. Segmentation faults and core dumps occurring while executing the test suite
   might indicate a real problem but always run again the tests after
   a clean make install to avoid inconsistencies from old objects.
7. If you see error messages like "Parse errors: Bad plan.
   You planned X tests but ran Y." it usually means that you are missing
   a perl module or the tested httpd module depends on another one
   not loaded in the httpd config.
8. If you see SSL certificate errors, remove t/conf/ssl/ca prior to 
   t/TEST -clean
9. perl 5.28 in MacOS homebrew seems to hang the test suite.  Invoking 
   /usr/bin/perl Makefile.PL -apxs ... will cause an older perl to be used.

Smoking Tests
-------------

Sometimes it's possible that the test is passing properly for the
first time, when it's run for the first time in the thread. But when
you run it again, the test might fail. It's important to run the
repetition smoke testing. For example to repeat the tests 5 times you
can run:

    t/SMOKE -times=5

It's also possible that a test will pass when it's run after a
particular test, but if moved to run after a different state it may
fail. For this reason by default the tests run in random order.

Since it's important to be able to reproduce the problem with the
random testing, whenever -order=random is used, the used seed is
printed to STDERR. Which can be then fed into the future tests with:
via APACHE_TEST_SEED environment variable.

By adding the option -order=repeat, the tests will be run in
alphabetical order.

Combining these two important smoke testing techniques, one can run
tests with:

    t/SMOKE -times=N -order=(repeat|random)

For example, to run the mod_rewrite tests 5 times, one would:

    t/SMOKE -times=5 -verbose t/modules/rewrite.t

So the tests can be repeated N times, and run in the following three
modes:

- randomize all tests
- repeat the whole tests suite N times

For configuration options and default settings run:

    t/SMOKE -help

For more information refer to the Apache::TestSmoke manpage.


Test Environment Configuration
------------------------------

The test server is configured with conf files like any normal Apache
server.  The tricky part is those conf files are generated by the
harness just prior to starting the server.  t/conf/httpd.conf is
generated by t/conf/httpd.conf.in.  If that does not exist, the
harness will generate a working configuration and will include
LoadModule (and AddModule for Apache 1.3) directives from the
httpd.conf associated with the httpd binary you are using for testing.
If t/conf/extra.conf.in exists, t/conf/extra.conf will be generated
from that, and an Include directive for that file will be put in the
generated t/conf/httpd.conf.  t/conf/apache_test_config.pm is
generated from the test configuration.  It contains all the
information about the configuration of your test server.  You can
access this information in test scripts by:
	my $env = Apache::TestConfig->thaw;
Apache::TestConfig access apache_test_config.pm and returns a hash
reference with all the information.  Look through
apache_test_config.pm, it's a lot of stuff.  Once these conf files are
generated, you have a working test environment, and they must be
'cleaned' if you wish to make changes to them.  To clean the
environment:
	t/TEST -clean
(Now you will have to specify your httpd binary when starting back up
again.)


More Information 
---------------- 

For more information on using the test harness and writing tests, see
the README in Apache-Test and the examples in Apache-Test/t.  

The test harness was originally written by Doug MacEachern and is
discussed on the httpd dev mailing list (dev@httpd.apache.org).  

It is also included in modperl-2.0 source along with tests for
modperl-2.0.