diff --git a/README.md b/README.md
index f84113e..925cc3e 100644
--- a/README.md
+++ b/README.md
@@ -232,6 +232,8 @@
 recommended that the swarm manager is specified on a worker node as it runs docker containers. Check
 out [Portainer] if you want to run a management UI for your swarm cluster.
 
+7. `elkserver` - Sets up the Elasticsearch, Logstash, and Kibana stack. This allows logging data to be search, analyzed, and visualized in real time. 
+
 If you run the `muchos setup` command and a failure occurs, you can repeat the command until setup
 completes. Any work that was successfully completed will not be repeated. While some setup steps can
 take over a minute, use `ctrl-c` to stop setup if it hangs for a long time. Just remember to run
@@ -260,6 +262,7 @@
  * Grafana Metrics and Monitoring - [http://metrics:3000/](http://metrics:3000/)
  * Mesos status - [http://leader1:5050/](http://leader1:5050/) (if `mesosmaster` configured on leader1)
  * Marathon status - [http://leader1:8080/](http://leader1:8080/) (if `mesosmaster` configured on leader1)
+ * Kibana status - [http://leader1:5601/](http://leader1:5601) (But Kibana is configured on all nodes)
 
 ## Run a Fluo application
 
@@ -389,3 +392,4 @@
 [checksums]: conf/checksums
 [HDFS HA]: https://hadoop.apache.org/docs/current/hadoop-project-dist/hadoop-hdfs/HDFSHighAvailabilityWithQJM.html
 [Accumulo HA]: https://accumulo.apache.org/1.9/accumulo_user_manual.html#_components
+[ELK Stack]: https://www.elastic.co/
diff --git a/ansible/docker.yml b/ansible/docker.yml
index f33ff13..7f63232 100644
--- a/ansible/docker.yml
+++ b/ansible/docker.yml
@@ -19,6 +19,7 @@
   become: yes
   roles:
     - docker
+
 - hosts: swarmmanager
   become: yes
   tasks:
@@ -30,13 +31,15 @@
       register: swarm_status
       changed_when: "'active' not in swarm_status.stdout_lines"
     - name: initialize swarm
-      shell: >
+      shell: |
+        docker swarm leave --force || echo "leaving swarm for multiple setups"
         docker swarm init --advertise-addr={{ ansible_default_ipv4.address }}:2377
       when: "'active' not in swarm_status.stdout_lines"
     - name: get swarm token
       command: docker swarm join-token -q worker
       register: swarm_token
       changed_when: "'active' not in swarm_status.stdout_lines"
+
 - hosts: workers:!swarmmanager
   become: yes
   vars:
diff --git a/ansible/elk.yml b/ansible/elk.yml
new file mode 100644
index 0000000..cd02578
--- /dev/null
+++ b/ansible/elk.yml
@@ -0,0 +1,27 @@
+---
+#
+# Licensed to the Apache Software Foundation (ASF) under one or more
+# contributor license agreements.  See the NOTICE file distributed with
+# this work for additional information regarding copyright ownership.
+# The ASF licenses this file to You under the Apache License, Version 2.0
+# (the "License"); you may not use this file except in compliance with
+# the License.  You may obtain a copy of the License at
+#
+#    http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+#
+#
+
+# Playbook to install the ELK stack + Beats
+#
+- hosts: all:!{{ azure_proxy_host }}
+  roles:
+    - { role: elasticsearch }
+    - { role: filebeat }
+    - { role: kibana }
+    - { role: logstash }
diff --git a/ansible/kill.yml b/ansible/kill.yml
index 93c984f..080ddf3 100644
--- a/ansible/kill.yml
+++ b/ansible/kill.yml
@@ -18,18 +18,22 @@
 - hosts: mesosmaster
   become: yes
   tasks:
-    - name: "stop mesos-master & marathon"
-      service: name={{ item }} state=stopped
-      when: "'mesosmaster' in groups"
-      with_items:
-        - mesos-master
-        - marathon
+  - name: "stop mesos-master & marathon"
+    service:
+      name: item
+      state: stopped
+    when: "'mesosmaster' in groups"
+    with_items:
+      - mesos-master
+      - marathon
 - hosts: workers
   become: yes
   tasks:
-    - name: "stop mesos slaves"
-      service: name=mesos-slave state=stopped
-      when: "'mesosmaster' in groups"
+  - name: "stop mesos slaves"
+    service:
+      name: mesos-slave
+      state: stopped
+    when: "'mesosmaster' in groups"
 - hosts: all:!{{ azure_proxy_host }}
   become: yes
   tasks:
diff --git a/ansible/roles/accumulo/tasks/main.yml b/ansible/roles/accumulo/tasks/main.yml
index b1341f4..8d5b9ba 100644
--- a/ansible/roles/accumulo/tasks/main.yml
+++ b/ansible/roles/accumulo/tasks/main.yml
@@ -74,7 +74,7 @@
 - name: "Copy the modified accumulo-cluster script that supports systemd to bin"
   copy: src=roles/accumulo/files/accumulo-cluster-systemd dest={{ accumulo_home }}/bin/accumulo-cluster-systemd mode=0755
   when: use_systemd
-- name: "Remove the exisiting accumulo-service and accumulo-cluster scripts"
+- name: "Remove the existing accumulo-service and accumulo-cluster scripts"
   file: path={{ accumulo_home }}/bin/{{ item }} state=absent
   with_items:
     - accumulo-service
diff --git a/ansible/roles/azure/tasks/log_analytics_ws_common.yml b/ansible/roles/azure/tasks/log_analytics_ws_common.yml
index 86fa102..10ff083 100644
--- a/ansible/roles/azure/tasks/log_analytics_ws_common.yml
+++ b/ansible/roles/azure/tasks/log_analytics_ws_common.yml
@@ -39,7 +39,7 @@
 
 - name: Query all the resources in the resource group
   azure_rm_resource_info:
-    resource_group:  "{{ resource_group }}"
+    resource_group: "{{ resource_group }}"
     resource_type: resources
   register: rgfacts
 
diff --git a/ansible/roles/elasticsearch/defaults/main.yml b/ansible/roles/elasticsearch/defaults/main.yml
new file mode 100644
index 0000000..38a8ade
--- /dev/null
+++ b/ansible/roles/elasticsearch/defaults/main.yml
@@ -0,0 +1,19 @@
+#
+# Licensed to the Apache Software Foundation (ASF) under one or more
+# contributor license agreements.  See the NOTICE file distributed with
+# this work for additional information regarding copyright ownership.
+# The ASF licenses this file to You under the Apache License, Version 2.0
+# (the "License"); you may not use this file except in compliance with
+# the License.  You may obtain a copy of the License at
+#
+#    http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+#
+
+elasticsearch_rpm: elasticsearch-oss-7.8.0-x86_64.rpm
+elasticsearch_checksum: "sha512:0dfaf62bafd6830ebbf571d9e264411913078781f5fcf57a6bd427bab01c4c001d66245dcb268317b65161e8fc2d4e3d020e2e38d4f3b8ad3477d99e17c2d9d1 "
diff --git a/ansible/roles/elasticsearch/defaults/workers b/ansible/roles/elasticsearch/defaults/workers
new file mode 100644
index 0000000..cd3348c
--- /dev/null
+++ b/ansible/roles/elasticsearch/defaults/workers
@@ -0,0 +1,3 @@
+{% for host in groups['workers'] %}
+{{ host }}
+{% endfor %}
diff --git a/ansible/roles/elasticsearch/tasks/main.yml b/ansible/roles/elasticsearch/tasks/main.yml
new file mode 100644
index 0000000..d041127
--- /dev/null
+++ b/ansible/roles/elasticsearch/tasks/main.yml
@@ -0,0 +1,83 @@
+---
+#
+# Licensed to the Apache Software Foundation (ASF) under one or more
+# contributor license agreements.  See the NOTICE file distributed with
+# this work for additional information regarding copyright ownership.
+# The ASF licenses this file to You under the Apache License, Version 2.0
+# (the "License"); you may not use this file except in compliance with
+# the License.  You may obtain a copy of the License at
+#
+#    http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+#
+
+#
+# Installing Elasticsearch
+#
+
+# Add the Elasticsearch yum repo.
+- name: "download elasticsearch rpm"
+  get_url:
+  args:
+    url: https://artifacts.elastic.co/downloads/elasticsearch/{{ elasticsearch_rpm }}
+    dest: /tmp/{{ elasticsearch_rpm }}
+    checksum: "{{ elasticsearch_checksum }}"
+    force: no
+
+# Install elasticsearch
+- name: "ensure elasticsearch is installed"
+  become: true
+  yum:
+    name: /tmp/{{ elasticsearch_rpm }}
+    state: present
+
+# Update Elasticsearch config file to allow access (to secure Elasticsearch, bind to 'localhost').
+- name: Updating the config file to allow outside access
+  lineinfile:
+    destfile: /etc/elasticsearch/elasticsearch.yml
+    regexp: "network.host:"
+    line: "network.host: 0.0.0.0"
+  become: true
+
+# Update Elasticsearch port in config file
+- name: Updating the port in config file
+  lineinfile:
+    destfile: /etc/elasticsearch/elasticsearch.yml
+    regexp: "http.port:"
+    line: "http.port: 9200"
+  become: true
+
+# Update Discovery Settings in config file
+- name: Update the Discovery Seed Host
+  lineinfile:
+    destfile: /etc/elasticsearch/elasticsearch.yml
+    regexp: "discovery.seed_hosts:"
+    line: "discovery.seed_hosts: [\"{{ groups['elkserver'][0] }}\"]"
+  become: true
+
+# Update Discovery Settings in config file
+- name: Update the Discovery Seed Host
+  lineinfile:
+    destfile: /etc/elasticsearch/elasticsearch.yml
+    regexp: "cluster.initial_master_nodes:"
+    line: "cluster.initial_master_nodes: [\"{{ groups['elkserver'][0] }}\"]"
+  become: true
+
+# Enable Elasticsearch
+- name: Enable Elasticsearch
+  service:
+    name: elasticsearch
+    enabled: yes
+  become: true
+
+# Restart Elasticsearch
+- name: Start Elasticsearch
+  service:
+    name: elasticsearch
+    state: started
+  become: yes
diff --git a/ansible/roles/filebeat/defaults/main.yml b/ansible/roles/filebeat/defaults/main.yml
new file mode 100644
index 0000000..d9290b9
--- /dev/null
+++ b/ansible/roles/filebeat/defaults/main.yml
@@ -0,0 +1,21 @@
+---
+#
+# Licensed to the Apache Software Foundation (ASF) under one or more
+# contributor license agreements.  See the NOTICE file distributed with
+# this work for additional information regarding copyright ownership.
+# The ASF licenses this file to You under the Apache License, Version 2.0
+# (the "License"); you may not use this file except in compliance with
+# the License.  You may obtain a copy of the License at
+#
+#    http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,e
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+#
+
+filebeat_rpm: filebeat-7.8.0-x86_64.rpm
+filebeat_checksum: "sha512:d3483622cc55f8e0e5a3198bb179bd6e74d66a50a6b6d8df82a3e22eae9b345886505fce9439003b8ab57b3cf70bcfbcfaec40ff3fbd41ff385f1fb9ae6a34e0"
+
diff --git a/ansible/roles/filebeat/tasks/main.yml b/ansible/roles/filebeat/tasks/main.yml
new file mode 100644
index 0000000..c48b315
--- /dev/null
+++ b/ansible/roles/filebeat/tasks/main.yml
@@ -0,0 +1,61 @@
+---
+#
+# Licensed to the Apache Software Foundation (ASF) under one or more
+# contributor license agreements.  See the NOTICE file distributed with
+# this work for additional information regarding copyright ownership.
+# The ASF licenses this file to You under the Apache License, Version 2.0
+# (the "License"); you may not use this file except in compliance with
+# the License.  You may obtain a copy of the License at
+#
+#    http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,e
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+#
+
+# Installing Filebeat
+#
+
+# download Filebeat
+- name: "download filebeat rpm"
+  get_url:
+  args:
+    url: https://artifacts.elastic.co/downloads/beats/filebeat/{{ filebeat_rpm }}
+    dest: /tmp/{{ filebeat_rpm }}
+    checksum: "{{ filebeat_checksum }}"
+    force: no
+
+  #Install filebeat"
+- name: "Install filebeat rpm"
+  become: true
+  yum:
+    name: /tmp/{{ filebeat_rpm }}
+    state: present
+
+#Configure Filebeat yml file
+
+- name: Copy filebeat.yml to /etc
+  template:
+    src: ../../filebeat/templates/filebeat.yml
+    dest: /etc/filebeat/
+    backup: yes
+  become: true
+
+- name: Copy filebeat.reference.yml to /etc
+  copy:
+    src: ../../filebeat/templates/filebeat.reference.yml
+    dest: /etc/filebeat/
+    backup: yes
+  become: true
+
+- name: Enable logstash module
+  command: filebeat modules enable logstash
+  become: true
+
+#Run Filebeat
+- name: Run Filebeat in the background
+  command: screen -d -m ./filebeat -e -c filebeat.yml -d "publish"
+  become: true
diff --git a/ansible/roles/filebeat/templates/filebeat.reference.yml b/ansible/roles/filebeat/templates/filebeat.reference.yml
new file mode 100644
index 0000000..9a35915
--- /dev/null
+++ b/ansible/roles/filebeat/templates/filebeat.reference.yml
@@ -0,0 +1,2071 @@
+#
+# Licensed to the Apache Software Foundation (ASF) under one or more
+# contributor license agreements.  See the NOTICE file distributed with
+# this work for additional information regarding copyright ownership.
+# The ASF licenses this file to You under the Apache License, Version 2.0
+# (the "License"); you may not use this file except in compliance with
+# the License.  You may obtain a copy of the License at
+#
+#    http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,e
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+#
+
+######################## Filebeat Configuration ############################
+
+# This file is a full configuration example documenting all non-deprecated
+# options in comments. For a shorter configuration example, that contains only
+# the most common options, please see filebeat.yml in the same directory.
+#
+# You can find the full configuration reference here:
+# https://www.elastic.co/guide/en/beats/filebeat/index.html
+
+#==========================  Modules configuration =============================
+filebeat.modules:
+  #-------------------------------- System Module --------------------------------
+  #- module: system
+  # Syslog
+  #syslog:
+  #enabled: true
+
+  # Set custom paths for the log files. If left empty,
+  # Filebeat will choose the paths depending on your OS.
+  #var.paths:
+
+  # Input configuration (advanced). Any input configuration option
+  # can be added under this section.
+  #input:
+
+  # Authorization logs
+  #auth:
+  #enabled: true
+
+  # Set custom paths for the log files. If left empty,
+  # Filebeat will choose the paths depending on your OS.
+  #var.paths:
+
+  # Input configuration (advanced). Any input configuration option
+  # can be added under this section.
+  #input:
+
+  #-------------------------------- Apache Module --------------------------------
+  #- module: apache
+  # Access logs
+  #access:
+  #enabled: true
+
+  # Set custom paths for the log files. If left empty,
+  # Filebeat will choose the paths depending on your OS.
+  #var.paths:
+
+  # Input configuration (advanced). Any input configuration option
+  # can be added under this section.
+  #input:
+
+  # Error logs
+  #error:
+  #enabled: true
+
+  # Set custom paths for the log files. If left empty,
+  # Filebeat will choose the paths depending on your OS.
+  #var.paths:
+
+  # Input configuration (advanced). Any input configuration option
+  # can be added under this section.
+  #input:
+
+  #-------------------------------- Auditd Module --------------------------------
+  #- module: auditd
+  #log:
+  #enabled: true
+
+  # Set custom paths for the log files. If left empty,
+  # Filebeat will choose the paths depending on your OS.
+  #var.paths:
+
+  # Input configuration (advanced). Any input configuration option
+  # can be added under this section.
+  #input:
+
+  #---------------------------- Elasticsearch Module ----------------------------
+  - module: elasticsearch
+    # Server log
+    server:
+      enabled: true
+      # Set custom paths for the log files. If left empty,
+      # Filebeat will choose the paths depending on your OS.
+      #var.paths:
+
+    gc:
+      enabled: true
+      # Set custom paths for the log files. If left empty,
+      # Filebeat will choose the paths depending on your OS.
+      #var.paths:
+
+    audit:
+      enabled: true
+      # Set custom paths for the log files. If left empty,
+      # Filebeat will choose the paths depending on your OS.
+      #var.paths:
+
+    slowlog:
+      enabled: true
+      # Set custom paths for the log files. If left empty,
+      # Filebeat will choose the paths depending on your OS.
+      #var.paths:
+
+    deprecation:
+      enabled: true
+      # Set custom paths for the log files. If left empty,
+      # Filebeat will choose the paths depending on your OS.
+      #var.paths:
+
+  #------------------------------- HAProxy Module -------------------------------
+  - module: haproxy
+    # All logs
+    log:
+      enabled: true
+      # Set which input to use between syslog (default) or file.
+      #var.input:
+      # Set custom paths for the log files. If left empty,
+      # Filebeat will choose the paths depending on your OS.
+      #var.paths:
+
+  #-------------------------------- Icinga Module --------------------------------
+  #- module: icinga
+  # Main logs
+  #main:
+  #enabled: true
+
+  # Set custom paths for the log files. If left empty,
+  # Filebeat will choose the paths depending on your OS.
+  #var.paths:
+
+  # Input configuration (advanced). Any input configuration option
+  # can be added under this section.
+  #input:
+
+  # Debug logs
+  #debug:
+  #enabled: true
+
+  # Set custom paths for the log files. If left empty,
+  # Filebeat will choose the paths depending on your OS.
+  #var.paths:
+
+  # Input configuration (advanced). Any input configuration option
+  # can be added under this section.
+  #input:
+
+  # Startup logs
+  #startup:
+  #enabled: true
+
+  # Set custom paths for the log files. If left empty,
+  # Filebeat will choose the paths depending on your OS.
+  #var.paths:
+
+  # Input configuration (advanced). Any input configuration option
+  # can be added under this section.
+  #input:
+
+  #--------------------------------- IIS Module ---------------------------------
+  #- module: iis
+  # Access logs
+  #access:
+  #enabled: true
+
+  # Set custom paths for the log files. If left empty,
+  # Filebeat will choose the paths depending on your OS.
+  #var.paths:
+
+  # Input configuration (advanced). Any input configuration option
+  # can be added under this section.
+  #input:
+
+  # Error logs
+  #error:
+  #enabled: true
+
+  # Set custom paths for the log files. If left empty,
+  # Filebeat will choose the paths depending on your OS.
+  #var.paths:
+
+  # Input configuration (advanced). Any input configuration option
+  # can be added under this section.
+  #input:
+
+  #-------------------------------- Kafka Module --------------------------------
+  - module: kafka
+    # All logs
+    log:
+      enabled: true
+      # Set custom paths for Kafka. If left empty,
+      # Filebeat will look under /opt.
+      #var.kafka_home:
+      # Set custom paths for the log files. If left empty,
+      # Filebeat will choose the paths depending on your OS.
+      #var.paths:
+
+  #-------------------------------- Kibana Module --------------------------------
+  - module: kibana
+    # All logs
+    log:
+      enabled: true
+      # Set custom paths for the log files. If left empty,
+      # Filebeat will choose the paths depending on your OS.
+      #var.paths:
+
+  #------------------------------- Logstash Module -------------------------------
+  #- module: logstash
+  # logs
+  #log:
+  #enabled: true
+
+  # Set custom paths for the log files. If left empty,
+  # Filebeat will choose the paths depending on your OS.
+  # var.paths:
+
+  # Slow logs
+  #slowlog:
+  #enabled: true
+
+  # Set custom paths for the log files. If left empty,
+  # Filebeat will choose the paths depending on your OS.
+  #var.paths:
+
+  #------------------------------- Mongodb Module -------------------------------
+  #- module: mongodb
+  # Logs
+  #log:
+  #enabled: true
+
+  # Set custom paths for the log files. If left empty,
+  # Filebeat will choose the paths depending on your OS.
+  #var.paths:
+
+  # Input configuration (advanced). Any input configuration option
+  # can be added under this section.
+  #input:
+
+  #-------------------------------- MySQL Module --------------------------------
+  #- module: mysql
+  # Error logs
+  #error:
+  #enabled: true
+
+  # Set custom paths for the log files. If left empty,
+  # Filebeat will choose the paths depending on your OS.
+  #var.paths:
+
+  # Input configuration (advanced). Any input configuration option
+  # can be added under this section.
+  #input:
+
+  # Slow logs
+  #slowlog:
+  #enabled: true
+
+  # Set custom paths for the log files. If left empty,
+  # Filebeat will choose the paths depending on your OS.
+  #var.paths:
+
+  # Input configuration (advanced). Any input configuration option
+  # can be added under this section.
+  #input:
+
+  #--------------------------------- NATS Module ---------------------------------
+  - module: nats
+    # All logs
+    log:
+      enabled: true
+      # Set custom paths for the log files. If left empty,
+      # Filebeat will choose the paths depending on your OS.
+      #var.paths:
+
+  #-------------------------------- Nginx Module --------------------------------
+  #- module: nginx
+  # Access logs
+  #access:
+  #enabled: true
+
+  # Set custom paths for the log files. If left empty,
+  # Filebeat will choose the paths depending on your OS.
+  #var.paths:
+
+  # Input configuration (advanced). Any input configuration option
+  # can be added under this section.
+  #input:
+
+  # Error logs
+  #error:
+  #enabled: true
+
+  # Set custom paths for the log files. If left empty,
+  # Filebeat will choose the paths depending on your OS.
+  #var.paths:
+
+  # Input configuration (advanced). Any input configuration option
+  # can be added under this section.
+  #input:
+
+  # Ingress-nginx controller logs. This is disabled by default. It could be used in Kubernetes environments to parse ingress-nginx logs
+  #ingress_controller:
+  #  enabled: false
+  #
+  #  # Set custom paths for the log files. If left empty,
+  #  # Filebeat will choose the paths depending on your OS.
+  #  #var.paths:
+
+  #------------------------------- Osquery Module -------------------------------
+  - module: osquery
+    result:
+      enabled: true
+      # Set custom paths for the log files. If left empty,
+      # Filebeat will choose the paths depending on your OS.
+      #var.paths:
+      # If true, all fields created by this module are prefixed with
+      # `osquery.result`. Set to false to copy the fields in the root
+      # of the document. The default is true.
+      #var.use_namespace: true
+
+  #------------------------------ PostgreSQL Module ------------------------------
+  #- module: postgresql
+  # Logs
+  #log:
+  #enabled: true
+
+  # Set custom paths for the log files. If left empty,
+  # Filebeat will choose the paths depending on your OS.
+  #var.paths:
+
+  # Input configuration (advanced). Any input configuration option
+  # can be added under this section.
+  #input:
+
+  #-------------------------------- Redis Module --------------------------------
+  #- module: redis
+  # Main logs
+  #log:
+  #enabled: true
+
+  # Set custom paths for the log files. If left empty,
+  # Filebeat will choose the paths depending on your OS.
+  #var.paths: ["/var/log/redis/redis-server.log*"]
+
+  # Slow logs, retrieved via the Redis API (SLOWLOG)
+  #slowlog:
+  #enabled: true
+
+  # The Redis hosts to connect to.
+  #var.hosts: ["localhost:6379"]
+
+  # Optional, the password to use when connecting to Redis.
+  #var.password:
+
+  #----------------------------- Google Santa Module -----------------------------
+  - module: santa
+    log:
+      enabled: true
+      # Set custom paths for the log files. If left empty,
+      # Filebeat will choose the the default path.
+      #var.paths:
+
+#------------------------------- Traefik Module -------------------------------
+#- module: traefik
+# Access logs
+#access:
+#enabled: true
+
+# Set custom paths for the log files. If left empty,
+# Filebeat will choose the paths depending on your OS.
+#var.paths:
+
+# Input configuration (advanced). Any input configuration option
+# can be added under this section.
+#input:
+
+#=========================== Filebeat inputs =============================
+
+# List of inputs to fetch data.
+filebeat.inputs:
+  # Each - is an input. Most options can be set at the input level, so
+  # you can use different inputs for various configurations.
+  # Below are the input specific configurations.
+
+  # Type of the files. Based on this the way the file is read is decided.
+  # The different types cannot be mixed in one input
+  #
+  # Possible options are:
+  # * log: Reads every line of the log file (default)
+  # * stdin: Reads the standard in
+
+  #------------------------------ Log input --------------------------------
+  - type: log
+
+    # Change to true to enable this input configuration.
+    enabled: false
+
+    # Paths that should be crawled and fetched. Glob based paths.
+    # To fetch all ".log" files from a specific level of subdirectories
+    # /var/log/*/*.log can be used.
+    # For each file found under this path, a harvester is started.
+    # Make sure not file is defined twice as this can lead to unexpected behaviour.
+    paths:
+      - /var/log/*.log
+      #- c:\programdata\elasticsearch\logs\*
+
+    # Configure the file encoding for reading files with international characters
+    # following the W3C recommendation for HTML5 (http://www.w3.org/TR/encoding).
+    # Some sample encodings:
+    #   plain, utf-8, utf-16be-bom, utf-16be, utf-16le, big5, gb18030, gbk,
+    #    hz-gb-2312, euc-kr, euc-jp, iso-2022-jp, shift-jis, ...
+    #encoding: plain
+
+    # Exclude lines. A list of regular expressions to match. It drops the lines that are
+    # matching any regular expression from the list. The include_lines is called before
+    # exclude_lines. By default, no lines are dropped.
+    #exclude_lines: ['^DBG']
+
+    # Include lines. A list of regular expressions to match. It exports the lines that are
+    # matching any regular expression from the list. The include_lines is called before
+    # exclude_lines. By default, all the lines are exported.
+    #include_lines: ['^ERR', '^WARN']
+
+    # Exclude files. A list of regular expressions to match. Filebeat drops the files that
+    # are matching any regular expression from the list. By default, no files are dropped.
+    #exclude_files: ['.gz$']
+
+    # Optional additional fields. These fields can be freely picked
+    # to add additional information to the crawled log files for filtering
+    #fields:
+    #  level: debug
+    #  review: 1
+
+    # Set to true to store the additional fields as top level fields instead
+    # of under the "fields" sub-dictionary. In case of name conflicts with the
+    # fields added by Filebeat itself, the custom fields overwrite the default
+    # fields.
+    #fields_under_root: false
+
+    # Set to true to publish fields with null values in events.
+    #keep_null: false
+
+    # Ignore files which were modified more then the defined timespan in the past.
+    # ignore_older is disabled by default, so no files are ignored by setting it to 0.
+    # Time strings like 2h (2 hours), 5m (5 minutes) can be used.
+    #ignore_older: 0
+
+    # How often the input checks for new files in the paths that are specified
+    # for harvesting. Specify 1s to scan the directory as frequently as possible
+    # without causing Filebeat to scan too frequently. Default: 10s.
+    #scan_frequency: 10s
+
+    # Defines the buffer size every harvester uses when fetching the file
+    #harvester_buffer_size: 16384
+
+    # Maximum number of bytes a single log event can have
+    # All bytes after max_bytes are discarded and not sent. The default is 10MB.
+    # This is especially useful for multiline log messages which can get large.
+    #max_bytes: 10485760
+
+    # Characters which separate the lines. Valid values: auto, line_feed, vertical_tab, form_feed,
+    # carriage_return, carriage_return_line_feed, next_line, line_separator, paragraph_separator.
+    #line_terminator: auto
+
+    ### Recursive glob configuration
+
+    # Expand "**" patterns into regular glob patterns.
+    #recursive_glob.enabled: true
+
+    ### JSON configuration
+
+    # Decode JSON options. Enable this if your logs are structured in JSON.
+    # JSON key on which to apply the line filtering and multiline settings. This key
+    # must be top level and its value must be string, otherwise it is ignored. If
+    # no text key is defined, the line filtering and multiline features cannot be used.
+    #json.message_key:
+
+    # By default, the decoded JSON is placed under a "json" key in the output document.
+    # If you enable this setting, the keys are copied top level in the output document.
+    #json.keys_under_root: false
+
+    # If keys_under_root and this setting are enabled, then the values from the decoded
+    # JSON object overwrite the fields that Filebeat normally adds (type, source, offset, etc.)
+    # in case of conflicts.
+    #json.overwrite_keys: false
+
+    # If this setting is enabled, Filebeat adds a "error.message" and "error.key: json" key in case of JSON
+    # unmarshaling errors or when a text key is defined in the configuration but cannot
+    # be used.
+    #json.add_error_key: false
+
+    ### Multiline options
+
+    # Multiline can be used for log messages spanning multiple lines. This is common
+    # for Java Stack Traces or C-Line Continuation
+
+    # The regexp Pattern that has to be matched. The example pattern matches all lines starting with [
+    #multiline.pattern: ^\[
+
+    # Defines if the pattern set under pattern should be negated or not. Default is false.
+    #multiline.negate: false
+
+    # Match can be set to "after" or "before". It is used to define if lines should be append to a pattern
+    # that was (not) matched before or after or as long as a pattern is not matched based on negate.
+    # Note: After is the equivalent to previous and before is the equivalent to to next in Logstash
+    #multiline.match: after
+
+    # The maximum number of lines that are combined to one event.
+    # In case there are more the max_lines the additional lines are discarded.
+    # Default is 500
+    #multiline.max_lines: 500
+
+    # After the defined timeout, an multiline event is sent even if no new pattern was found to start a new event
+    # Default is 5s.
+    #multiline.timeout: 5s
+
+    # Setting tail_files to true means filebeat starts reading new files at the end
+    # instead of the beginning. If this is used in combination with log rotation
+    # this can mean that the first entries of a new file are skipped.
+    #tail_files: false
+
+    # The Ingest Node pipeline ID associated with this input. If this is set, it
+    # overwrites the pipeline option from the Elasticsearch output.
+    #pipeline:
+
+    # If symlinks is enabled, symlinks are opened and harvested. The harvester is opening the
+    # original for harvesting but will report the symlink name as source.
+    #symlinks: false
+
+    # Backoff values define how aggressively filebeat crawls new files for updates
+    # The default values can be used in most cases. Backoff defines how long it is waited
+    # to check a file again after EOF is reached. Default is 1s which means the file
+    # is checked every second if new lines were added. This leads to a near real time crawling.
+    # Every time a new line appears, backoff is reset to the initial value.
+    #backoff: 1s
+
+    # Max backoff defines what the maximum backoff time is. After having backed off multiple times
+    # from checking the files, the waiting time will never exceed max_backoff independent of the
+    # backoff factor. Having it set to 10s means in the worst case a new line can be added to a log
+    # file after having backed off multiple times, it takes a maximum of 10s to read the new line
+    #max_backoff: 10s
+
+    # The backoff factor defines how fast the algorithm backs off. The bigger the backoff factor,
+    # the faster the max_backoff value is reached. If this value is set to 1, no backoff will happen.
+    # The backoff value will be multiplied each time with the backoff_factor until max_backoff is reached
+    #backoff_factor: 2
+
+    # Max number of harvesters that are started in parallel.
+    # Default is 0 which means unlimited
+    #harvester_limit: 0
+
+    ### Harvester closing options
+
+    # Close inactive closes the file handler after the predefined period.
+    # The period starts when the last line of the file was, not the file ModTime.
+    # Time strings like 2h (2 hours), 5m (5 minutes) can be used.
+    #close_inactive: 5m
+
+    # Close renamed closes a file handler when the file is renamed or rotated.
+    # Note: Potential data loss. Make sure to read and understand the docs for this option.
+    #close_renamed: false
+
+    # When enabling this option, a file handler is closed immediately in case a file can't be found
+    # any more. In case the file shows up again later, harvesting will continue at the last known position
+    # after scan_frequency.
+    #close_removed: true
+
+    # Closes the file handler as soon as the harvesters reaches the end of the file.
+    # By default this option is disabled.
+    # Note: Potential data loss. Make sure to read and understand the docs for this option.
+    #close_eof: false
+
+    ### State options
+
+    # Files for the modification data is older then clean_inactive the state from the registry is removed
+    # By default this is disabled.
+    #clean_inactive: 0
+
+    # Removes the state for file which cannot be found on disk anymore immediately
+    #clean_removed: true
+
+    # Close timeout closes the harvester after the predefined time.
+    # This is independent if the harvester did finish reading the file or not.
+    # By default this option is disabled.
+    # Note: Potential data loss. Make sure to read and understand the docs for this option.
+    #close_timeout: 0
+
+    # Defines if inputs is enabled
+    #enabled: true
+
+#----------------------------- Stdin input -------------------------------
+# Configuration to use stdin input
+#- type: stdin
+
+#------------------------- Redis slowlog input ---------------------------
+# Experimental: Config options for the redis slow log input
+#- type: redis
+#enabled: false
+
+# List of hosts to pool to retrieve the slow log information.
+#hosts: ["localhost:6379"]
+
+# How often the input checks for redis slow log.
+#scan_frequency: 10s
+
+# Timeout after which time the input should return an error
+#timeout: 1s
+
+# Network type to be used for redis connection. Default: tcp
+#network: tcp
+
+# Max number of concurrent connections. Default: 10
+#maxconn: 10
+
+# Redis AUTH password. Empty by default.
+#password: foobared
+
+#------------------------------ Udp input --------------------------------
+# Experimental: Config options for the udp input
+#- type: udp
+#enabled: false
+
+# Maximum size of the message received over UDP
+#max_message_size: 10KiB
+
+# Size of the UDP read buffer in bytes
+#read_buffer: 0
+
+#------------------------------ TCP input --------------------------------
+# Experimental: Config options for the TCP input
+#- type: tcp
+#enabled: false
+
+# The host and port to receive the new event
+#host: "localhost:9000"
+
+# Character used to split new message
+#line_delimiter: "\n"
+
+# Maximum size in bytes of the message received over TCP
+#max_message_size: 20MiB
+
+# Max number of concurrent connections, or 0 for no limit. Default: 0
+#max_connections: 0
+
+# The number of seconds of inactivity before a remote connection is closed.
+#timeout: 300s
+
+# Use SSL settings for TCP.
+#ssl.enabled: true
+
+# List of supported/valid TLS versions. By default all TLS versions 1.0 up to
+# 1.2 are enabled.
+#ssl.supported_protocols: [TLSv1.0, TLSv1.1, TLSv1.2]
+
+# SSL configuration. By default is off.
+# List of root certificates for client verifications
+#ssl.certificate_authorities: ["/etc/pki/root/ca.pem"]
+
+# Certificate for SSL server authentication.
+#ssl.certificate: "/etc/pki/client/cert.pem"
+
+# Server Certificate Key,
+#ssl.key: "/etc/pki/client/cert.key"
+
+# Optional passphrase for decrypting the Certificate Key.
+#ssl.key_passphrase: ''
+
+# Configure cipher suites to be used for SSL connections.
+#ssl.cipher_suites: []
+
+# Configure curve types for ECDHE based cipher suites.
+#ssl.curve_types: []
+
+# Configure what types of client authentication are supported. Valid options
+# are `none`, `optional`, and `required`. When `certificate_authorities` is set it will
+# default to `required` otherwise it will be set to `none`.
+#ssl.client_authentication: "required"
+
+#------------------------------ Syslog input --------------------------------
+# Experimental: Config options for the Syslog input
+# Accept RFC3164 formatted syslog event via UDP.
+#- type: syslog
+#enabled: false
+#protocol.udp:
+# The host and port to receive the new event
+#host: "localhost:9000"
+
+# Maximum size of the message received over UDP
+#max_message_size: 10KiB
+
+# Accept RFC3164 formatted syslog event via TCP.
+#- type: syslog
+#enabled: false
+
+#protocol.tcp:
+# The host and port to receive the new event
+#host: "localhost:9000"
+
+# Character used to split new message
+#line_delimiter: "\n"
+
+# Maximum size in bytes of the message received over TCP
+#max_message_size: 20MiB
+
+# The number of seconds of inactivity before a remote connection is closed.
+#timeout: 300s
+
+# Use SSL settings for TCP.
+#ssl.enabled: true
+
+# List of supported/valid TLS versions. By default all TLS versions 1.0 up to
+# 1.2 are enabled.
+#ssl.supported_protocols: [TLSv1.0, TLSv1.1, TLSv1.2]
+
+# SSL configuration. By default is off.
+# List of root certificates for client verifications
+#ssl.certificate_authorities: ["/etc/pki/root/ca.pem"]
+
+# Certificate for SSL server authentication.
+#ssl.certificate: "/etc/pki/client/cert.pem"
+
+# Server Certificate Key,
+#ssl.key: "/etc/pki/client/cert.key"
+
+# Optional passphrase for decrypting the Certificate Key.
+#ssl.key_passphrase: ''
+
+# Configure cipher suites to be used for SSL connections.
+#ssl.cipher_suites: []
+
+# Configure curve types for ECDHE based cipher suites.
+#ssl.curve_types: []
+
+# Configure what types of client authentication are supported. Valid options
+# are `none`, `optional`, and `required`. When `certificate_authorities` is set it will
+# default to `required` otherwise it will be set to `none`.
+#ssl.client_authentication: "required"
+
+#------------------------------ Container input --------------------------------
+#- type: container
+#enabled: false
+
+# Paths for container logs that should be crawled and fetched.
+#paths:
+#  -/var/lib/docker/containers/*/*.log
+
+# Configure stream to filter to a specific stream: stdout, stderr or all (default)
+#stream: all
+
+#========================== Filebeat autodiscover ==============================
+
+# Autodiscover allows you to detect changes in the system and spawn new modules
+# or inputs as they happen.
+
+#filebeat.autodiscover:
+# List of enabled autodiscover providers
+#  providers:
+#    - type: docker
+#      templates:
+#        - condition:
+#            equals.docker.container.image: busybox
+#          config:
+#            - type: container
+#              paths:
+#                - /var/lib/docker/containers/${data.docker.container.id}/*.log
+
+#========================= Filebeat global options ============================
+
+# Registry data path. If a relative path is used, it is considered relative to the
+# data path.
+#filebeat.registry.path: ${path.data}/registry
+
+# The permissions mask to apply on registry data, and meta files. The default
+# value is 0600.  Must be a valid Unix-style file permissions mask expressed in
+# octal notation.  This option is not supported on Windows.
+#filebeat.registry.file_permissions: 0600
+
+# The timeout value that controls when registry entries are written to disk
+# (flushed). When an unwritten update exceeds this value, it triggers a write
+# to disk. When flush is set to 0s, the registry is written to disk after each
+# batch of events has been published successfully. The default value is 0s.
+#filebeat.registry.flush: 0s
+
+# Starting with Filebeat 7.0, the registry uses a new directory format to store
+# Filebeat state. After you upgrade, Filebeat will automatically migrate a 6.x
+# registry file to use the new directory format. If you changed
+# filebeat.registry.path while upgrading, set filebeat.registry.migrate_file to
+# point to the old registry file.
+#filebeat.registry.migrate_file: ${path.data}/registry
+
+# By default Ingest pipelines are not updated if a pipeline with the same ID
+# already exists. If this option is enabled Filebeat overwrites pipelines
+# everytime a new Elasticsearch connection is established.
+#filebeat.overwrite_pipelines: false
+
+# How long filebeat waits on shutdown for the publisher to finish.
+# Default is 0, not waiting.
+#filebeat.shutdown_timeout: 0
+
+# Enable filebeat config reloading
+#filebeat.config:
+#inputs:
+#enabled: false
+#path: inputs.d/*.yml
+#reload.enabled: true
+#reload.period: 10s
+#modules:
+#enabled: false
+#path: modules.d/*.yml
+#reload.enabled: true
+#reload.period: 10s
+
+#================================ General ======================================
+
+# The name of the shipper that publishes the network data. It can be used to group
+# all the transactions sent by a single shipper in the web interface.
+# If this options is not defined, the hostname is used.
+#name:
+
+# The tags of the shipper are included in their own field with each
+# transaction published. Tags make it easy to group servers by different
+# logical properties.
+#tags: ["service-X", "web-tier"]
+
+# Optional fields that you can specify to add additional information to the
+# output. Fields can be scalar values, arrays, dictionaries, or any nested
+# combination of these.
+#fields:
+#  env: staging
+
+# If this option is set to true, the custom fields are stored as top-level
+# fields in the output document instead of being grouped under a fields
+# sub-dictionary. Default is false.
+#fields_under_root: false
+
+# Internal queue configuration for buffering events to be published.
+#queue:
+# Queue type by name (default 'mem')
+# The memory queue will present all available events (up to the outputs
+# bulk_max_size) to the output, the moment the output is ready to server
+# another batch of events.
+#mem:
+# Max number of events the queue can buffer.
+#events: 4096
+
+# Hints the minimum number of events stored in the queue,
+# before providing a batch of events to the outputs.
+# The default value is set to 2048.
+# A value of 0 ensures events are immediately available
+# to be sent to the outputs.
+#flush.min_events: 2048
+
+# Maximum duration after which events are available to the outputs,
+# if the number of events stored in the queue is < `flush.min_events`.
+#flush.timeout: 1s
+
+# The spool queue will store events in a local spool file, before
+# forwarding the events to the outputs.
+#
+# Beta: spooling to disk is currently a beta feature. Use with care.
+#
+# The spool file is a circular buffer, which blocks once the file/buffer is full.
+# Events are put into a write buffer and flushed once the write buffer
+# is full or the flush_timeout is triggered.
+# Once ACKed by the output, events are removed immediately from the queue,
+# making space for new events to be persisted.
+#spool:
+# The file namespace configures the file path and the file creation settings.
+# Once the file exists, the `size`, `page_size` and `prealloc` settings
+# will have no more effect.
+#file:
+# Location of spool file. The default value is ${path.data}/spool.dat.
+#path: "${path.data}/spool.dat"
+
+# Configure file permissions if file is created. The default value is 0600.
+#permissions: 0600
+
+# File size hint. The spool blocks, once this limit is reached. The default value is 100 MiB.
+#size: 100MiB
+
+# The files page size. A file is split into multiple pages of the same size. The default value is 4KiB.
+#page_size: 4KiB
+
+# If prealloc is set, the required space for the file is reserved using
+# truncate. The default value is true.
+#prealloc: true
+
+# Spool writer settings
+# Events are serialized into a write buffer. The write buffer is flushed if:
+# - The buffer limit has been reached.
+# - The configured limit of buffered events is reached.
+# - The flush timeout is triggered.
+#write:
+# Sets the write buffer size.
+#buffer_size: 1MiB
+
+# Maximum duration after which events are flushed if the write buffer
+# is not full yet. The default value is 1s.
+#flush.timeout: 1s
+
+# Number of maximum buffered events. The write buffer is flushed once the
+# limit is reached.
+#flush.events: 16384
+
+# Configure the on-disk event encoding. The encoding can be changed
+# between restarts.
+# Valid encodings are: json, ubjson, and cbor.
+#codec: cbor
+#read:
+# Reader flush timeout, waiting for more events to become available, so
+# to fill a complete batch as required by the outputs.
+# If flush_timeout is 0, all available events are forwarded to the
+# outputs immediately.
+# The default value is 0s.
+#flush.timeout: 0s
+
+# Sets the maximum number of CPUs that can be executing simultaneously. The
+# default is the number of logical CPUs available in the system.
+#max_procs:
+
+#================================ Processors ===================================
+
+# Processors are used to reduce the number of fields in the exported event or to
+# enhance the event with external metadata. This section defines a list of
+# processors that are applied one by one and the first one receives the initial
+# event:
+#
+#   event -> filter1 -> event1 -> filter2 ->event2 ...
+#
+# The supported processors are drop_fields, drop_event, include_fields,
+# decode_json_fields, and add_cloud_metadata.
+#
+# For example, you can use the following processors to keep the fields that
+# contain CPU load percentages, but remove the fields that contain CPU ticks
+# values:
+#
+#processors:
+#  - include_fields:
+#      fields: ["cpu"]
+#  - drop_fields:
+#      fields: ["cpu.user", "cpu.system"]
+#
+# The following example drops the events that have the HTTP response code 200:
+#
+#processors:
+#  - drop_event:
+#      when:
+#        equals:
+#          http.code: 200
+#
+# The following example renames the field a to b:
+#
+#processors:
+#  - rename:
+#      fields:
+#        - from: "a"
+#          to: "b"
+#
+# The following example tokenizes the string into fields:
+#
+#processors:
+#  - dissect:
+#      tokenizer: "%{key1} - %{key2}"
+#      field: "message"
+#      target_prefix: "dissect"
+#
+# The following example enriches each event with metadata from the cloud
+# provider about the host machine. It works on EC2, GCE, DigitalOcean,
+# Tencent Cloud, and Alibaba Cloud.
+#
+#processors:
+#  - add_cloud_metadata: ~
+#
+# The following example enriches each event with the machine's local time zone
+# offset from UTC.
+#
+#processors:
+#  - add_locale:
+#      format: offset
+#
+# The following example enriches each event with docker metadata, it matches
+# given fields to an existing container id and adds info from that container:
+#
+#processors:
+#  - add_docker_metadata:
+#      host: "unix:///var/run/docker.sock"
+#      match_fields: ["system.process.cgroup.id"]
+#      match_pids: ["process.pid", "process.ppid"]
+#      match_source: true
+#      match_source_index: 4
+#      match_short_id: false
+#      cleanup_timeout: 60
+#      labels.dedot: false
+#      # To connect to Docker over TLS you must specify a client and CA certificate.
+#      #ssl:
+#      #  certificate_authority: "/etc/pki/root/ca.pem"
+#      #  certificate:           "/etc/pki/client/cert.pem"
+#      #  key:                   "/etc/pki/client/cert.key"
+#
+# The following example enriches each event with docker metadata, it matches
+# container id from log path available in `source` field (by default it expects
+# it to be /var/lib/docker/containers/*/*.log).
+#
+#processors:
+#  - add_docker_metadata: ~
+#
+# The following example enriches each event with host metadata.
+#
+#processors:
+#  - add_host_metadata: ~
+#
+# The following example enriches each event with process metadata using
+# process IDs included in the event.
+#
+#processors:
+#  - add_process_metadata:
+#      match_pids: ["system.process.ppid"]
+#      target: system.process.parent
+#
+# The following example decodes fields containing JSON strings
+# and replaces the strings with valid JSON objects.
+#
+#processors:
+#  - decode_json_fields:
+#      fields: ["field1", "field2", ...]
+#      process_array: false
+#      max_depth: 1
+#      target: ""
+#      overwrite_keys: false
+#
+#processors:
+#  - decompress_gzip_field:
+#      from: "field1"
+#      to: "field2"
+#      ignore_missing: false
+#      fail_on_error: true
+#
+# The following example copies the value of message to message_copied
+#
+#processors:
+#  - copy_fields:
+#      fields:
+#        - from: message
+#          to: message_copied
+#      fail_on_error: true
+#      ignore_missing: false
+#
+# The following example truncates the value of message to 1024 bytes
+#
+#processors:
+#  - truncate_fields:
+#      fields:
+#        - message
+#      max_bytes: 1024
+#      fail_on_error: false
+#      ignore_missing: true
+#
+# The following example preserves the raw message under event.original
+#
+#processors:
+#  - copy_fields:
+#      fields:
+#        - from: message
+#          to: event.original
+#      fail_on_error: false
+#      ignore_missing: true
+#  - truncate_fields:
+#      fields:
+#        - event.original
+#      max_bytes: 1024
+#      fail_on_error: false
+#      ignore_missing: true
+
+#============================= Elastic Cloud ==================================
+
+# These settings simplify using Filebeat with the Elastic Cloud (https://cloud.elastic.co/).
+
+# The cloud.id setting overwrites the `output.elasticsearch.hosts` and
+# `setup.kibana.host` options.
+# You can find the `cloud.id` in the Elastic Cloud web UI.
+#cloud.id:
+
+# The cloud.auth setting overwrites the `output.elasticsearch.username` and
+# `output.elasticsearch.password` settings. The format is `<user>:<pass>`.
+#cloud.auth:
+
+#================================ Outputs ======================================
+
+# Configure what output to use when sending the data collected by the beat.
+
+#-------------------------- Elasticsearch output -------------------------------
+output.elasticsearch:
+  # Boolean flag to enable or disable the output module.
+  #enabled: true
+
+  # Array of hosts to connect to.
+  # Scheme and port can be left out and will be set to the default (http and 9200)
+  # In case you specify and additional path, the scheme is required: http://localhost:9200/path
+  # IPv6 addresses should always be defined as: https://[2001:db8::1]:9200
+  hosts: ["localhost:9200"]
+
+  # Set gzip compression level.
+  #compression_level: 0
+  # Configure escaping HTML symbols in strings.
+  #escape_html: false
+  # Protocol - either `http` (default) or `https`.
+  #protocol: "https"
+  # Authentication credentials - either API key or username/password.
+  #api_key: "id:api_key"
+  #username: "elastic"
+  #password: "changeme"
+  # Dictionary of HTTP parameters to pass within the URL with index operations.
+  #parameters:
+  #param1: value1
+  #param2: value2
+  # Number of workers per Elasticsearch host.
+  #worker: 1
+  # Optional index name. The default is "filebeat" plus date
+  # and generates [filebeat-]YYYY.MM.DD keys.
+  # In case you modify this pattern you must update setup.template.name and setup.template.pattern accordingly.
+  #index: "filebeat-%{[agent.version]}-%{+yyyy.MM.dd}"
+  # Optional ingest node pipeline. By default no pipeline will be used.
+  #pipeline: ""
+  # Optional HTTP path
+  #path: "/elasticsearch"
+  # Custom HTTP headers to add to each request
+  #headers:
+  #  X-My-Header: Contents of the header
+  # Proxy server URL
+  #proxy_url: http://proxy:3128
+  # Whether to disable proxy settings for outgoing connections. If true, this
+  # takes precedence over both the proxy_url field and any environment settings
+  # (HTTP_PROXY, HTTPS_PROXY). The default is false.
+  #proxy_disable: false
+  # The number of times a particular Elasticsearch index operation is attempted. If
+  # the indexing operation doesn't succeed after this many retries, the events are
+  # dropped. The default is 3.
+  #max_retries: 3
+  # The maximum number of events to bulk in a single Elasticsearch bulk API index request.
+  # The default is 50.
+  #bulk_max_size: 50
+  # The number of seconds to wait before trying to reconnect to Elasticsearch
+  # after a network error. After waiting backoff.init seconds, the Beat
+  # tries to reconnect. If the attempt fails, the backoff timer is increased
+  # exponentially up to backoff.max. After a successful connection, the backoff
+  # timer is reset. The default is 1s.
+  #backoff.init: 1s
+  # The maximum number of seconds to wait before attempting to connect to
+  # Elasticsearch after a network error. The default is 60s.
+  #backoff.max: 60s
+  # Configure HTTP request timeout before failing a request to Elasticsearch.
+  #timeout: 90
+  # Use SSL settings for HTTPS.
+  #ssl.enabled: true
+  # Configure SSL verification mode. If `none` is configured, all server hosts
+  # and certificates will be accepted. In this mode, SSL-based connections are
+  # susceptible to man-in-the-middle attacks. Use only for testing. Default is
+  # `full`.
+  #ssl.verification_mode: full
+  # List of supported/valid TLS versions. By default all TLS versions from 1.1
+  # up to 1.3 are enabled.
+  #ssl.supported_protocols: [TLSv1.1, TLSv1.2, TLSv1.3]
+  # List of root certificates for HTTPS server verifications
+  #ssl.certificate_authorities: ["/etc/pki/root/ca.pem"]
+  # Certificate for SSL client authentication
+  #ssl.certificate: "/etc/pki/client/cert.pem"
+  # Client certificate key
+  #ssl.key: "/etc/pki/client/cert.key"
+  # Optional passphrase for decrypting the certificate key.
+  #ssl.key_passphrase: ''
+  # Configure cipher suites to be used for SSL connections
+  #ssl.cipher_suites: []
+  # Configure curve types for ECDHE-based cipher suites
+  #ssl.curve_types: []
+  # Configure what types of renegotiation are supported. Valid options are
+  # never, once, and freely. Default is never.
+  #ssl.renegotiation: never
+  # Configure a pin that can be used to do extra validation of the verified certificate chain,
+  # this allow you to ensure that a specific certificate is used to validate the chain of trust.
+  #
+  # The pin is a base64 encoded string of the SHA-256 fingerprint.
+  #ssl.ca_sha256
+
+#----------------------------- Logstash output ---------------------------------
+output.logstash:
+  # Boolean flag to enable or disable the output module.
+  enabled: true
+
+  # The Logstash hosts
+  hosts: ["localhost:5044"]
+
+  # Number of workers per Logstash host.
+  worker: 1
+
+  # Set gzip compression level.
+  compression_level: 3
+
+  # Configure escaping HTML symbols in strings.
+  escape_html: false
+
+  # Optional maximum time to live for a connection to Logstash, after which the
+  # connection will be re-established.  A value of `0s` (the default) will
+  # disable this feature.
+  #
+  # Not yet supported for async connections (i.e. with the "pipelining" option set)
+  #ttl: 30s
+
+  # Optionally load-balance events between Logstash hosts. Default is false.
+  #loadbalance: false
+
+  # Number of batches to be sent asynchronously to Logstash while processing
+  # new batches.
+  pipelining: 2
+
+  # If enabled only a subset of events in a batch of events is transferred per
+  # transaction.  The number of events to be sent increases up to `bulk_max_size`
+  # if no error is encountered.
+  slow_start: false
+
+  # The number of seconds to wait before trying to reconnect to Logstash
+  # after a network error. After waiting backoff.init seconds, the Beat
+  # tries to reconnect. If the attempt fails, the backoff timer is increased
+  # exponentially up to backoff.max. After a successful connection, the backoff
+  # timer is reset. The default is 1s.
+  backoff.init: 1s
+
+  # The maximum number of seconds to wait before attempting to connect to
+  # Logstash after a network error. The default is 60s.
+  backoff.max: 60s
+
+  # Optional index name. The default index name is set to filebeat
+  # in all lowercase.
+  index: "filebeat"
+
+  # SOCKS5 proxy server URL
+  #proxy_url: socks5://user:password@socks5-server:2233
+
+  # Resolve names locally when using a proxy server. Defaults to false.
+  #proxy_use_local_resolver: false
+
+  # Enable SSL support. SSL is automatically enabled if any SSL setting is set.
+  #ssl.enabled: true
+
+  # Configure SSL verification mode. If `none` is configured, all server hosts
+  # and certificates will be accepted. In this mode, SSL based connections are
+  # susceptible to man-in-the-middle attacks. Use only for testing. Default is
+  # `full`.
+  #ssl.verification_mode: full
+
+  # List of supported/valid TLS versions. By default all TLS versions from 1.1
+  # up to 1.3 are enabled.
+  #ssl.supported_protocols: [TLSv1.1, TLSv1.2, TLSv1.3]
+
+  # Optional SSL configuration options. SSL is off by default.
+  # List of root certificates for HTTPS server verifications
+  #ssl.certificate_authorities: ["/etc/pki/root/ca.pem"]
+
+  # Certificate for SSL client authentication
+  #ssl.certificate: "/etc/pki/client/cert.pem"
+
+  # Client certificate key
+  #ssl.key: "/etc/pki/client/cert.key"
+
+  # Optional passphrase for decrypting the Certificate Key.
+  #ssl.key_passphrase: ''
+
+  # Configure cipher suites to be used for SSL connections
+  #ssl.cipher_suites: []
+
+  # Configure curve types for ECDHE-based cipher suites
+  #ssl.curve_types: []
+
+  # Configure what types of renegotiation are supported. Valid options are
+  # never, once, and freely. Default is never.
+  #ssl.renegotiation: never
+
+  # Configure a pin that can be used to do extra validation of the verified certificate chain,
+  # this allow you to ensure that a specific certificate is used to validate the chain of trust.
+  #
+  # The pin is a base64 encoded string of the SHA-256 fingerprint.
+  #ssl.ca_sha256
+
+  # The number of times to retry publishing an event after a publishing failure.
+  # After the specified number of retries, the events are typically dropped.
+  # Some Beats, such as Filebeat and Winlogbeat, ignore the max_retries setting
+  # and retry until all events are published.  Set max_retries to a value less
+  # than 0 to retry until all events are published. The default is 3.
+  max_retries: 3
+
+  # The maximum number of events to bulk in a single Logstash request. The
+  # default is 2048.
+  bulk_max_size: 2048
+
+  # The number of seconds to wait for responses from the Logstash server before
+  # timing out. The default is 30s.
+  timeout: 30s
+
+#------------------------------- Kafka output ----------------------------------
+#output.kafka:
+# Boolean flag to enable or disable the output module.
+#enabled: true
+
+# The list of Kafka broker addresses from which to fetch the cluster metadata.
+# The cluster metadata contain the actual Kafka brokers events are published
+# to.
+#hosts: ["localhost:9092"]
+
+# The Kafka topic used for produced events. The setting can be a format string
+# using any event field. To set the topic from document type use `%{[type]}`.
+#topic: beats
+
+# The Kafka event key setting. Use format string to create a unique event key.
+# By default no event key will be generated.
+#key: ''
+
+# The Kafka event partitioning strategy. Default hashing strategy is `hash`
+# using the `output.kafka.key` setting or randomly distributes events if
+# `output.kafka.key` is not configured.
+#partition.hash:
+# If enabled, events will only be published to partitions with reachable
+# leaders. Default is false.
+#reachable_only: false
+
+# Configure alternative event field names used to compute the hash value.
+# If empty `output.kafka.key` setting will be used.
+# Default value is empty list.
+#hash: []
+
+# Authentication details. Password is required if username is set.
+#username: ''
+#password: ''
+
+# Kafka version Filebeat is assumed to run against. Defaults to the "1.0.0".
+#version: '1.0.0'
+
+# Configure JSON encoding
+#codec.json:
+# Pretty-print JSON event
+#pretty: false
+
+# Configure escaping HTML symbols in strings.
+#escape_html: false
+
+# Metadata update configuration. Metadata contains leader information
+# used to decide which broker to use when publishing.
+#metadata:
+# Max metadata request retry attempts when cluster is in middle of leader
+# election. Defaults to 3 retries.
+#retry.max: 3
+
+# Wait time between retries during leader elections. Default is 250ms.
+#retry.backoff: 250ms
+
+# Refresh metadata interval. Defaults to every 10 minutes.
+#refresh_frequency: 10m
+
+# Strategy for fetching the topics metadata from the broker. Default is false.
+#full: false
+
+# The number of concurrent load-balanced Kafka output workers.
+#worker: 1
+
+# The number of times to retry publishing an event after a publishing failure.
+# After the specified number of retries, events are typically dropped.
+# Some Beats, such as Filebeat, ignore the max_retries setting and retry until
+# all events are published.  Set max_retries to a value less than 0 to retry
+# until all events are published. The default is 3.
+#max_retries: 3
+
+# The maximum number of events to bulk in a single Kafka request. The default
+# is 2048.
+#bulk_max_size: 2048
+
+# Duration to wait before sending bulk Kafka request. 0 is no delay. The default
+# is 0.
+#bulk_flush_frequency: 0s
+
+# The number of seconds to wait for responses from the Kafka brokers before
+# timing out. The default is 30s.
+#timeout: 30s
+
+# The maximum duration a broker will wait for number of required ACKs. The
+# default is 10s.
+#broker_timeout: 10s
+
+# The number of messages buffered for each Kafka broker. The default is 256.
+#channel_buffer_size: 256
+
+# The keep-alive period for an active network connection. If 0s, keep-alives
+# are disabled. The default is 0 seconds.
+#keep_alive: 0
+
+# Sets the output compression codec. Must be one of none, snappy and gzip. The
+# default is gzip.
+#compression: gzip
+
+# Set the compression level. Currently only gzip provides a compression level
+# between 0 and 9. The default value is chosen by the compression algorithm.
+#compression_level: 4
+
+# The maximum permitted size of JSON-encoded messages. Bigger messages will be
+# dropped. The default value is 1000000 (bytes). This value should be equal to
+# or less than the broker's message.max.bytes.
+#max_message_bytes: 1000000
+
+# The ACK reliability level required from broker. 0=no response, 1=wait for
+# local commit, -1=wait for all replicas to commit. The default is 1.  Note:
+# If set to 0, no ACKs are returned by Kafka. Messages might be lost silently
+# on error.
+#required_acks: 1
+
+# The configurable ClientID used for logging, debugging, and auditing
+# purposes.  The default is "beats".
+#client_id: beats
+
+# Enable SSL support. SSL is automatically enabled if any SSL setting is set.
+#ssl.enabled: true
+
+# Optional SSL configuration options. SSL is off by default.
+# List of root certificates for HTTPS server verifications
+#ssl.certificate_authorities: ["/etc/pki/root/ca.pem"]
+
+# Configure SSL verification mode. If `none` is configured, all server hosts
+# and certificates will be accepted. In this mode, SSL based connections are
+# susceptible to man-in-the-middle attacks. Use only for testing. Default is
+# `full`.
+#ssl.verification_mode: full
+
+# List of supported/valid TLS versions. By default all TLS versions from 1.1
+# up to 1.3 are enabled.
+#ssl.supported_protocols: [TLSv1.1, TLSv1.2, TLSv1.3]
+
+# Certificate for SSL client authentication
+#ssl.certificate: "/etc/pki/client/cert.pem"
+
+# Client Certificate Key
+#ssl.key: "/etc/pki/client/cert.key"
+
+# Optional passphrase for decrypting the Certificate Key.
+#ssl.key_passphrase: ''
+
+# Configure cipher suites to be used for SSL connections
+#ssl.cipher_suites: []
+
+# Configure curve types for ECDHE-based cipher suites
+#ssl.curve_types: []
+
+# Configure what types of renegotiation are supported. Valid options are
+# never, once, and freely. Default is never.
+#ssl.renegotiation: never
+
+# Authentication type to use with Kerberos. Available options: keytab, password.
+#kerberos.auth_type: password
+
+# Path to the keytab file. It is used when auth_type is set to keytab.
+#kerberos.keytab: /etc/security/keytabs/kafka.keytab
+
+# Path to the Kerberos configuration.
+#kerberos.config_path: /etc/krb5.conf
+
+# The service name. Service principal name is contructed from
+# service_name/hostname@realm.
+#kerberos.service_name: kafka
+
+# Name of the Kerberos user.
+#kerberos.username: elastic
+
+# Password of the Kerberos user. It is used when auth_type is set to password.
+#kerberos.password: changeme
+
+# Kerberos realm.
+#kerberos.realm: ELASTIC
+
+#------------------------------- Redis output ----------------------------------
+#output.redis:
+# Boolean flag to enable or disable the output module.
+#enabled: true
+
+# Configure JSON encoding
+#codec.json:
+# Pretty print json event
+#pretty: false
+
+# Configure escaping HTML symbols in strings.
+#escape_html: false
+
+# The list of Redis servers to connect to. If load-balancing is enabled, the
+# events are distributed to the servers in the list. If one server becomes
+# unreachable, the events are distributed to the reachable servers only.
+# The hosts setting supports redis and rediss urls with custom password like
+# redis://:password@localhost:6379.
+#hosts: ["localhost:6379"]
+
+# The name of the Redis list or channel the events are published to. The
+# default is filebeat.
+#key: filebeat
+
+# The password to authenticate to Redis with. The default is no authentication.
+#password:
+
+# The Redis database number where the events are published. The default is 0.
+#db: 0
+
+# The Redis data type to use for publishing events. If the data type is list,
+# the Redis RPUSH command is used. If the data type is channel, the Redis
+# PUBLISH command is used. The default value is list.
+#datatype: list
+
+# The number of workers to use for each host configured to publish events to
+# Redis. Use this setting along with the loadbalance option. For example, if
+# you have 2 hosts and 3 workers, in total 6 workers are started (3 for each
+# host).
+#worker: 1
+
+# If set to true and multiple hosts or workers are configured, the output
+# plugin load balances published events onto all Redis hosts. If set to false,
+# the output plugin sends all events to only one host (determined at random)
+# and will switch to another host if the currently selected one becomes
+# unreachable. The default value is true.
+#loadbalance: true
+
+# The Redis connection timeout in seconds. The default is 5 seconds.
+#timeout: 5s
+
+# The number of times to retry publishing an event after a publishing failure.
+# After the specified number of retries, the events are typically dropped.
+# Some Beats, such as Filebeat, ignore the max_retries setting and retry until
+# all events are published. Set max_retries to a value less than 0 to retry
+# until all events are published. The default is 3.
+#max_retries: 3
+
+# The number of seconds to wait before trying to reconnect to Redis
+# after a network error. After waiting backoff.init seconds, the Beat
+# tries to reconnect. If the attempt fails, the backoff timer is increased
+# exponentially up to backoff.max. After a successful connection, the backoff
+# timer is reset. The default is 1s.
+#backoff.init: 1s
+
+# The maximum number of seconds to wait before attempting to connect to
+# Redis after a network error. The default is 60s.
+#backoff.max: 60s
+
+# The maximum number of events to bulk in a single Redis request or pipeline.
+# The default is 2048.
+#bulk_max_size: 2048
+
+# The URL of the SOCKS5 proxy to use when connecting to the Redis servers. The
+# value must be a URL with a scheme of socks5://.
+#proxy_url:
+
+# This option determines whether Redis hostnames are resolved locally when
+# using a proxy. The default value is false, which means that name resolution
+# occurs on the proxy server.
+#proxy_use_local_resolver: false
+
+# Enable SSL support. SSL is automatically enabled, if any SSL setting is set.
+#ssl.enabled: true
+
+# Configure SSL verification mode. If `none` is configured, all server hosts
+# and certificates will be accepted. In this mode, SSL based connections are
+# susceptible to man-in-the-middle attacks. Use only for testing. Default is
+# `full`.
+#ssl.verification_mode: full
+
+# List of supported/valid TLS versions. By default all TLS versions from 1.1
+# up to 1.3 are enabled.
+#ssl.supported_protocols: [TLSv1.1, TLSv1.2, TLSv1.3]
+
+# Optional SSL configuration options. SSL is off by default.
+# List of root certificates for HTTPS server verifications
+#ssl.certificate_authorities: ["/etc/pki/root/ca.pem"]
+
+# Certificate for SSL client authentication
+#ssl.certificate: "/etc/pki/client/cert.pem"
+
+# Client Certificate Key
+#ssl.key: "/etc/pki/client/cert.key"
+
+# Optional passphrase for decrypting the Certificate Key.
+#ssl.key_passphrase: ''
+
+# Configure cipher suites to be used for SSL connections
+#ssl.cipher_suites: []
+
+# Configure curve types for ECDHE based cipher suites
+#ssl.curve_types: []
+
+# Configure what types of renegotiation are supported. Valid options are
+# never, once, and freely. Default is never.
+#ssl.renegotiation: never
+
+#------------------------------- File output -----------------------------------
+#output.file:
+# Boolean flag to enable or disable the output module.
+#enabled: true
+
+# Configure JSON encoding
+#codec.json:
+# Pretty-print JSON event
+#pretty: false
+
+# Configure escaping HTML symbols in strings.
+#escape_html: false
+
+# Path to the directory where to save the generated files. The option is
+# mandatory.
+#path: "/tmp/filebeat"
+
+# Name of the generated files. The default is `filebeat` and it generates
+# files: `filebeat`, `filebeat.1`, `filebeat.2`, etc.
+#filename: filebeat
+
+# Maximum size in kilobytes of each file. When this size is reached, and on
+# every Filebeat restart, the files are rotated. The default value is 10240
+# kB.
+#rotate_every_kb: 10000
+
+# Maximum number of files under path. When this number of files is reached,
+# the oldest file is deleted and the rest are shifted from last to first. The
+# default is 7 files.
+#number_of_files: 7
+
+# Permissions to use for file creation. The default is 0600.
+#permissions: 0600
+
+#----------------------------- Console output ---------------------------------
+#output.console:
+# Boolean flag to enable or disable the output module.
+#enabled: true
+
+# Configure JSON encoding
+#codec.json:
+# Pretty-print JSON event
+#pretty: false
+
+# Configure escaping HTML symbols in strings.
+#escape_html: false
+
+#================================= Paths ======================================
+
+# The home path for the Filebeat installation. This is the default base path
+# for all other path settings and for miscellaneous files that come with the
+# distribution (for example, the sample dashboards).
+# If not set by a CLI flag or in the configuration file, the default for the
+# home path is the location of the binary.
+path.home: /usr/share/filebeat/
+
+# The configuration path for the Filebeat installation. This is the default
+# base path for configuration files, including the main YAML configuration file
+# and the Elasticsearch template file. If not set by a CLI flag or in the
+# configuration file, the default for the configuration path is the home path.
+path.config: /etc/filebeat
+
+# The data path for the Filebeat installation. This is the default base path
+# for all the files in which Filebeat needs to store its data. If not set by a
+# CLI flag or in the configuration file, the default for the data path is a data
+# subdirectory inside the home path.
+path.data: /usr/share/filebeat
+
+# The logs path for a Filebeat installation. This is the default location for
+# the Beat's log files. If not set by a CLI flag or in the configuration file,
+# the default for the logs path is a logs subdirectory inside the home path.
+path.logs: ${path.home}/logs
+
+#================================ Keystore ==========================================
+# Location of the Keystore containing the keys and their sensitive values.
+#keystore.path: "${path.config}/beats.keystore"
+
+#============================== Dashboards =====================================
+# These settings control loading the sample dashboards to the Kibana index. Loading
+# the dashboards are disabled by default and can be enabled either by setting the
+# options here, or by using the `-setup` CLI flag or the `setup` command.
+#setup.dashboards.enabled: false
+
+# The directory from where to read the dashboards. The default is the `kibana`
+# folder in the home path.
+#setup.dashboards.directory: ${path.home}/kibana
+
+# The URL from where to download the dashboards archive. It is used instead of
+# the directory if it has a value.
+#setup.dashboards.url:
+
+# The file archive (zip file) from where to read the dashboards. It is used instead
+# of the directory when it has a value.
+#setup.dashboards.file:
+
+# In case the archive contains the dashboards from multiple Beats, this lets you
+# select which one to load. You can load all the dashboards in the archive by
+# setting this to the empty string.
+#setup.dashboards.beat: filebeat
+
+# The name of the Kibana index to use for setting the configuration. Default is ".kibana"
+#setup.dashboards.kibana_index: .kibana
+
+# The Elasticsearch index name. This overwrites the index name defined in the
+# dashboards and index pattern. Example: testbeat-*
+#setup.dashboards.index:
+
+# Always use the Kibana API for loading the dashboards instead of autodetecting
+# how to install the dashboards by first querying Elasticsearch.
+#setup.dashboards.always_kibana: false
+
+# If true and Kibana is not reachable at the time when dashboards are loaded,
+# it will retry to reconnect to Kibana instead of exiting with an error.
+#setup.dashboards.retry.enabled: false
+
+# Duration interval between Kibana connection retries.
+#setup.dashboards.retry.interval: 1s
+
+# Maximum number of retries before exiting with an error, 0 for unlimited retrying.
+#setup.dashboards.retry.maximum: 0
+
+#============================== Template =====================================
+
+# A template is used to set the mapping in Elasticsearch
+# By default template loading is enabled and the template is loaded.
+# These settings can be adjusted to load your own template or overwrite existing ones.
+
+# Set to false to disable template loading.
+#setup.template.enabled: true
+
+# Template name. By default the template name is "filebeat-%{[agent.version]}"
+# The template name and pattern has to be set in case the Elasticsearch index pattern is modified.
+#setup.template.name: "filebeat-%{[agent.version]}"
+
+# Template pattern. By default the template pattern is "-%{[agent.version]}-*" to apply to the default index settings.
+# The first part is the version of the beat and then -* is used to match all daily indices.
+# The template name and pattern has to be set in case the Elasticsearch index pattern is modified.
+#setup.template.pattern: "filebeat-%{[agent.version]}-*"
+
+# Path to fields.yml file to generate the template
+#setup.template.fields: "${path.config}/fields.yml"
+
+# A list of fields to be added to the template and Kibana index pattern. Also
+# specify setup.template.overwrite: true to overwrite the existing template.
+#setup.template.append_fields:
+#- name: field_name
+#  type: field_type
+
+# Enable JSON template loading. If this is enabled, the fields.yml is ignored.
+#setup.template.json.enabled: false
+
+# Path to the JSON template file
+#setup.template.json.path: "${path.config}/template.json"
+
+# Name under which the template is stored in Elasticsearch
+#setup.template.json.name: ""
+
+# Overwrite existing template
+#setup.template.overwrite: false
+
+# Elasticsearch template settings
+setup.template.settings:
+  # A dictionary of settings to place into the settings.index dictionary
+  # of the Elasticsearch template. For more details, please check
+  # https://www.elastic.co/guide/en/elasticsearch/reference/current/mapping.html
+  #index:
+  #number_of_shards: 1
+  #codec: best_compression
+  # A dictionary of settings for the _source field. For more details, please check
+  # https://www.elastic.co/guide/en/elasticsearch/reference/current/mapping-source-field.html
+  #_source:
+  #enabled: false
+
+#============================== Setup ILM =====================================
+
+# Configure index lifecycle management (ILM). These settings create a write
+# alias and add additional settings to the index template. When ILM is enabled,
+# output.elasticsearch.index is ignored, and the write alias is used to set the
+# index name.
+
+# Enable ILM support. Valid values are true, false, and auto. When set to auto
+# (the default), the Beat uses index lifecycle management when it connects to a
+# cluster that supports ILM; otherwise, it creates daily indices.
+#setup.ilm.enabled: auto
+
+# Set the prefix used in the index lifecycle write alias name. The default alias
+# name is 'filebeat-%{[agent.version]}'.
+#setup.ilm.rollover_alias: "filebeat"
+
+# Set the rollover index pattern. The default is "%{now/d}-000001".
+#setup.ilm.pattern: "{now/d}-000001"
+
+# Set the lifecycle policy name. The default policy name is
+# 'filebeat'.
+#setup.ilm.policy_name: "mypolicy"
+
+# The path to a JSON file that contains a lifecycle policy configuration. Used
+# to load your own lifecycle policy.
+#setup.ilm.policy_file:
+
+# Disable the check for an existing lifecycle policy. The default is true. If
+# you disable this check, set setup.ilm.overwrite: true so the lifecycle policy
+# can be installed.
+#setup.ilm.check_exists: true
+
+# Overwrite the lifecycle policy at startup. The default is false.
+#setup.ilm.overwrite: false
+
+#============================== Kibana =====================================
+
+# Starting with Beats version 6.0.0, the dashboards are loaded via the Kibana API.
+# This requires a Kibana endpoint configuration.
+setup.kibana:
+  # Kibana Host
+  # Scheme and port can be left out and will be set to the default (http and 5601)
+  # In case you specify and additional path, the scheme is required: http://localhost:5601/path
+  # IPv6 addresses should always be defined as: https://[2001:db8::1]:5601
+  #host: "localhost:5601"
+  # Optional protocol and basic auth credentials.
+  #protocol: "https"
+  #username: "elastic"
+  #password: "changeme"
+  # Optional HTTP path
+  #path: ""
+  # Optional Kibana space ID.
+  #space.id: ""
+  # Use SSL settings for HTTPS. Default is true.
+  #ssl.enabled: true
+  # Configure SSL verification mode. If `none` is configured, all server hosts
+  # and certificates will be accepted. In this mode, SSL based connections are
+  # susceptible to man-in-the-middle attacks. Use only for testing. Default is
+  # `full`.
+  #ssl.verification_mode: full
+  # List of supported/valid TLS versions. By default all TLS versions from 1.1
+  # up to 1.3 are enabled.
+  #ssl.supported_protocols: [TLSv1.1, TLSv1.2, TLSv1.3]
+  # SSL configuration. The default is off.
+  # List of root certificates for HTTPS server verifications
+  #ssl.certificate_authorities: ["/etc/pki/root/ca.pem"]
+  # Certificate for SSL client authentication
+  #ssl.certificate: "/etc/pki/client/cert.pem"
+  # Client certificate key
+  #ssl.key: "/etc/pki/client/cert.key"
+  # Optional passphrase for decrypting the certificate key.
+  #ssl.key_passphrase: ''
+  # Configure cipher suites to be used for SSL connections
+  #ssl.cipher_suites: []
+  # Configure curve types for ECDHE-based cipher suites
+  #ssl.curve_types: []
+
+#================================ Logging ======================================
+# There are four options for the log output: file, stderr, syslog, eventlog
+# The file output is the default.
+
+# Sets log level. The default log level is info.
+# Available log levels are: error, warning, info, debug
+#logging.level: info
+
+# Enable debug output for selected components. To enable all selectors use ["*"]
+# Other available selectors are "beat", "publish", "service"
+# Multiple selectors can be chained.
+#logging.selectors: [ ]
+
+# Send all logging output to stderr. The default is false.
+#logging.to_stderr: false
+
+# Send all logging output to syslog. The default is false.
+#logging.to_syslog: false
+
+# Send all logging output to Windows Event Logs. The default is false.
+#logging.to_eventlog: false
+
+# If enabled, Filebeat periodically logs its internal metrics that have changed
+# in the last period. For each metric that changed, the delta from the value at
+# the beginning of the period is logged. Also, the total values for
+# all non-zero internal metrics are logged on shutdown. The default is true.
+#logging.metrics.enabled: true
+
+# The period after which to log the internal metrics. The default is 30s.
+#logging.metrics.period: 30s
+
+# Logging to rotating files. Set logging.to_files to false to disable logging to
+# files.
+logging.to_files: true
+logging.files:
+  # Configure the path where the logs are written. The default is the logs directory
+  # under the home path (the binary location).
+  #path: /var/log/filebeat
+  # The name of the files where the logs are written to.
+  #name: filebeat
+  # Configure log file size limit. If limit is reached, log file will be
+  # automatically rotated
+  #rotateeverybytes: 10485760 # = 10MB
+  # Number of rotated log files to keep. Oldest files will be deleted first.
+  #keepfiles: 7
+  # The permissions mask to apply when rotating log files. The default value is 0600.
+  # Must be a valid Unix-style file permissions mask expressed in octal notation.
+  #permissions: 0600
+  # Enable log file rotation on time intervals in addition to size-based rotation.
+  # Intervals must be at least 1s. Values of 1m, 1h, 24h, 7*24h, 30*24h, and 365*24h
+  # are boundary-aligned with minutes, hours, days, weeks, months, and years as
+  # reported by the local system clock. All other intervals are calculated from the
+  # Unix epoch. Defaults to disabled.
+  #interval: 0
+  # Rotate existing logs on startup rather than appending to the existing
+  # file. Defaults to true.
+  # rotateonstartup: true
+# Set to true to log messages in JSON format.
+#logging.json: false
+
+#============================== X-Pack Monitoring ===============================
+# Filebeat can export internal metrics to a central Elasticsearch monitoring
+# cluster.  This requires xpack monitoring to be enabled in Elasticsearch.  The
+# reporting is disabled by default.
+
+# Set to true to enable the monitoring reporter.
+#monitoring.enabled: false
+
+# Sets the UUID of the Elasticsearch cluster under which monitoring data for this
+# Filebeat instance will appear in the Stack Monitoring UI. If output.elasticsearch
+# is enabled, the UUID is derived from the Elasticsearch cluster referenced by output.elasticsearch.
+#monitoring.cluster_uuid:
+
+# Uncomment to send the metrics to Elasticsearch. Most settings from the
+# Elasticsearch output are accepted here as well.
+# Note that the settings should point to your Elasticsearch *monitoring* cluster.
+# Any setting that is not set is automatically inherited from the Elasticsearch
+# output configuration, so if you have the Elasticsearch output configured such
+# that it is pointing to your Elasticsearch monitoring cluster, you can simply
+# uncomment the following line.
+#monitoring.elasticsearch:
+
+# Array of hosts to connect to.
+# Scheme and port can be left out and will be set to the default (http and 9200)
+# In case you specify and additional path, the scheme is required: http://localhost:9200/path
+# IPv6 addresses should always be defined as: https://[2001:db8::1]:9200
+#hosts: ["localhost:9200"]
+
+# Set gzip compression level.
+#compression_level: 0
+
+# Protocol - either `http` (default) or `https`.
+#protocol: "https"
+
+# Authentication credentials - either API key or username/password.
+#api_key: "id:api_key"
+#username: "beats_system"
+#password: "changeme"
+
+# Dictionary of HTTP parameters to pass within the URL with index operations.
+#parameters:
+#param1: value1
+#param2: value2
+
+# Custom HTTP headers to add to each request
+#headers:
+#  X-My-Header: Contents of the header
+
+# Proxy server url
+#proxy_url: http://proxy:3128
+
+# The number of times a particular Elasticsearch index operation is attempted. If
+# the indexing operation doesn't succeed after this many retries, the events are
+# dropped. The default is 3.
+#max_retries: 3
+
+# The maximum number of events to bulk in a single Elasticsearch bulk API index request.
+# The default is 50.
+#bulk_max_size: 50
+
+# The number of seconds to wait before trying to reconnect to Elasticsearch
+# after a network error. After waiting backoff.init seconds, the Beat
+# tries to reconnect. If the attempt fails, the backoff timer is increased
+# exponentially up to backoff.max. After a successful connection, the backoff
+# timer is reset. The default is 1s.
+#backoff.init: 1s
+
+# The maximum number of seconds to wait before attempting to connect to
+# Elasticsearch after a network error. The default is 60s.
+#backoff.max: 60s
+
+# Configure HTTP request timeout before failing an request to Elasticsearch.
+#timeout: 90
+
+# Use SSL settings for HTTPS.
+#ssl.enabled: true
+
+# Configure SSL verification mode. If `none` is configured, all server hosts
+# and certificates will be accepted. In this mode, SSL based connections are
+# susceptible to man-in-the-middle attacks. Use only for testing. Default is
+# `full`.
+#ssl.verification_mode: full
+
+# List of supported/valid TLS versions. By default all TLS versions from 1.1
+# up to 1.3 are enabled.
+#ssl.supported_protocols: [TLSv1.1, TLSv1.2, TLSv1.3]
+
+# SSL configuration. The default is off.
+# List of root certificates for HTTPS server verifications
+#ssl.certificate_authorities: ["/etc/pki/root/ca.pem"]
+
+# Certificate for SSL client authentication
+#ssl.certificate: "/etc/pki/client/cert.pem"
+
+# Client certificate key
+#ssl.key: "/etc/pki/client/cert.key"
+
+# Optional passphrase for decrypting the certificate key.
+#ssl.key_passphrase: ''
+
+# Configure cipher suites to be used for SSL connections
+#ssl.cipher_suites: []
+
+# Configure curve types for ECDHE-based cipher suites
+#ssl.curve_types: []
+
+# Configure what types of renegotiation are supported. Valid options are
+# never, once, and freely. Default is never.
+#ssl.renegotiation: never
+
+#metrics.period: 10s
+#state.period: 1m
+
+# The `monitoring.cloud.id` setting overwrites the `monitoring.elasticsearch.hosts`
+# setting. You can find the value for this setting in the Elastic Cloud web UI.
+#monitoring.cloud.id:
+
+# The `monitoring.cloud.auth` setting overwrites the `monitoring.elasticsearch.username`
+# and `monitoring.elasticsearch.password` settings. The format is `<user>:<pass>`.
+#monitoring.cloud.auth:
+
+#================================ HTTP Endpoint ======================================
+# Each beat can expose internal metrics through a HTTP endpoint. For security
+# reasons the endpoint is disabled by default. This feature is currently experimental.
+# Stats can be access through http://localhost:5066/stats . For pretty JSON output
+# append ?pretty to the URL.
+
+# Defines if the HTTP endpoint is enabled.
+#http.enabled: false
+
+# The HTTP endpoint will bind to this hostname, IP address, unix socket or named pipe.
+# When using IP addresses, it is recommended to only use localhost.
+#http.host: localhost
+
+# Port on which the HTTP endpoint will bind. Default is 5066.
+#http.port: 5066
+
+# Define which user should be owning the named pipe.
+#http.named_pipe.user:
+
+# Define which the permissions that should be applied to the named pipe, use the Security
+# Descriptor Definition Language (SDDL) to define the permission. This option cannot be used with
+# `http.user`.
+#http.named_pipe.security_descriptor:
+
+#============================= Process Security ================================
+
+# Enable or disable seccomp system call filtering on Linux. Default is enabled.
+#seccomp.enabled: true
+
+#================================= Migration ==================================
+
+# This allows to enable 6.7 migration aliases
+#migration.6_to_7.enabled: false
diff --git a/ansible/roles/filebeat/templates/filebeat.yml b/ansible/roles/filebeat/templates/filebeat.yml
new file mode 100644
index 0000000..47be999
--- /dev/null
+++ b/ansible/roles/filebeat/templates/filebeat.yml
@@ -0,0 +1,235 @@
+#
+# Licensed to the Apache Software Foundation (ASF) under one or more
+# contributor license agreements.  See the NOTICE file distributed with
+# this work for additional information regarding copyright ownership.
+# The ASF licenses this file to You under the Apache License, Version 2.0
+# (the "License"); you may not use this file except in compliance with
+# the License.  You may obtain a copy of the License at
+#
+#    http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,e
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+#
+
+###################### Filebeat Configuration Example #########################
+
+# This file is an example configuration file highlighting only the most common
+# options. The filebeat.reference.yml file from the same directory contains all the
+# supported options with more comments. You can use it as a reference.
+#
+# You can find the full configuration reference here:
+# https://www.elastic.co/guide/en/beats/filebeat/index.html
+
+# For more available modules and options, please see the filebeat.reference.yml sample
+# configuration file.
+
+# ============================== Filebeat inputs ===============================
+
+filebeat.inputs:
+  # Each - is an input. Most options can be set at the input level, so
+  # you can use different inputs for various configurations.
+  # Below are the input specific configurations.
+
+  - type: log
+
+    # Change to true to enable this input configuration.
+    enabled: true
+
+    # Paths that should be crawled and fetched. Glob based paths.
+    paths:
+      - "{{ worker_data_dirs[0] }}/logs/accumulo/*.log"
+      - "{{ worker_data_dirs[0] }}/logs/zookeeper/*log"
+      - "{{ worker_data_dirs[0] }}/logs/hadoop/*.log"
+
+    # Exclude lines. A list of regular expressions to match. It drops the lines that are
+    # matching any regular expression from the list.
+    #exclude_lines: ['^DBG']
+
+    # Include lines. A list of regular expressions to match. It exports the lines that are
+    # matching any regular expression from the list.
+    #include_lines: ['^ERR', '^WARN']
+
+    # Exclude files. A list of regular expressions to match. Filebeat drops the files that
+    # are matching any regular expression from the list. By default, no files are dropped.
+    #exclude_files: ['.gz$']
+
+    # Optional additional fields. These fields can be freely picked
+    # to add additional information to the crawled log files for filtering
+    #fields:
+    #  level: debug
+    #  review: 1
+
+    ### Multiline options
+
+    # Multiline can be used for log messages spanning multiple lines. This is common
+    # for Java Stack Traces or C-Line Continuation
+
+    # The regexp Pattern that has to be matched. The example pattern matches all lines starting with [
+    #multiline.pattern: ^\[
+
+    # Defines if the pattern set under pattern should be negated or not. Default is false.
+    #multiline.negate: false
+
+    # Match can be set to "after" or "before". It is used to define if lines should be append to a pattern
+    # that was (not) matched before or after or as long as a pattern is not matched based on negate.
+    # Note: After is the equivalent to previous and before is the equivalent to to next in Logstash
+    #multiline.match: after
+
+# ============================== Filebeat modules ==============================
+
+filebeat.config.modules:
+  # Glob pattern for configuration loading
+  path: ${path.config}/modules.d/*.yml
+
+  # Set to true to enable config reloading
+  reload.enabled: false
+
+  # Period on which files under path should be checked for changes
+  #reload.period: 10s
+
+# ======================= Elasticsearch template setting =======================
+
+setup.template.settings:
+  index.number_of_shards: 1
+  #index.codec: best_compression
+  #_source.enabled: false
+
+# ================================== General ===================================
+
+# The name of the shipper that publishes the network data. It can be used to group
+# all the transactions sent by a single shipper in the web interface.
+#name:
+
+# The tags of the shipper are included in their own field with each
+# transaction published.
+#tags: ["service-X", "web-tier"]
+
+# Optional fields that you can specify to add additional information to the
+# output.
+#fields:
+#  env: staging
+
+# ================================= Dashboards =================================
+# These settings control loading the sample dashboards to the Kibana index. Loading
+# the dashboards is disabled by default and can be enabled either by setting the
+# options here or by using the `setup` command.
+#setup.dashboards.enabled: false
+
+# The URL from where to download the dashboards archive. By default this URL
+# has a value which is computed based on the Beat name and version. For released
+# versions, this URL points to the dashboard archive on the artifacts.elastic.co
+# website.
+#setup.dashboards.url:
+
+# =================================== Kibana ===================================
+
+# Starting with Beats version 6.0.0, the dashboards are loaded via the Kibana API.
+# This requires a Kibana endpoint configuration.
+setup.kibana:
+  # Kibana Host
+  # Scheme and port can be left out and will be set to the default (http and 5601)
+  # In case you specify and additional path, the scheme is required: http://localhost:5601/path
+  # IPv6 addresses should always be defined as: https://[2001:db8::1]:5601
+  #host: "localhost:5601"
+  # Kibana Space ID
+  # ID of the Kibana Space into which the dashboards should be loaded. By default,
+  # the Default Space will be used.
+  #space.id:
+
+# =============================== Elastic Cloud ================================
+
+# These settings simplify using Filebeat with the Elastic Cloud (https://cloud.elastic.co/).
+
+# The cloud.id setting overwrites the `output.elasticsearch.hosts` and
+# `setup.kibana.host` options.
+# You can find the `cloud.id` in the Elastic Cloud web UI.
+#cloud.id:
+
+# The cloud.auth setting overwrites the `output.elasticsearch.username` and
+# `output.elasticsearch.password` settings. The format is `<user>:<pass>`.
+#cloud.auth:
+
+# ================================== Outputs ===================================
+
+# Configure what output to use when sending the data collected by the beat.
+
+# ---------------------------- Elasticsearch Output ----------------------------
+#output.elasticsearch:
+# Array of hosts to connect to.
+# hosts: ["localhost:9200"]
+
+# Protocol - either `http` (default) or `https`.
+#protocol: "https"
+
+# Authentication credentials - either API key or username/password.
+#api_key: "id:api_key"
+#username: "elastic"
+#password: "changeme"
+
+# ------------------------------ Logstash Output -------------------------------
+output.logstash:
+  # The Logstash hosts
+  hosts: ["localhost:5044"]
+
+  # Optional SSL. By default is off.
+  # List of root certificates for HTTPS server verifications
+  #ssl.certificate_authorities: ["/etc/pki/root/ca.pem"]
+  # Certificate for SSL client authentication
+  #ssl.certificate: "/etc/pki/client/cert.pem"
+  # Client Certificate Key
+  #ssl.key: "/etc/pki/client/cert.key"
+
+# ================================= Processors =================================
+processors:
+  - add_host_metadata:
+      when.not.contains.tags: forwarded
+  - add_cloud_metadata: ~
+  - add_docker_metadata: ~
+  - add_kubernetes_metadata: ~
+# ================================== Logging ===================================
+
+# Sets log level. The default log level is info.
+# Available log levels are: error, warning, info, debug
+#logging.level: info
+#   logging.to_files: true
+#  logging.files:
+#   path: /var/log/filebeat
+#  name: filebeat.log
+# keepfiles: 7
+#permissions: 0644
+
+# At debug level, you can selectively enable logging only for some components.
+# To enable all selectors use ["*"]. Examples of other selectors are "beat",
+# "publish", "service".
+#logging.selectors: ["*"]
+
+# ============================= X-Pack Monitoring ==============================
+# Filebeat can export internal metrics to a central Elasticsearch monitoring
+# cluster.  This requires xpack monitoring to be enabled in Elasticsearch.  The
+# reporting is disabled by default.
+
+# Set to true to enable the monitoring reporter.
+#monitoring.enabled: false
+
+# Sets the UUID of the Elasticsearch cluster under which monitoring data for this
+# Filebeat instance will appear in the Stack Monitoring UI. If output.elasticsearch
+# is enabled, the UUID is derived from the Elasticsearch cluster referenced by output.elasticsearch.
+#monitoring.cluster_uuid:
+
+# Uncomment to send the metrics to Elasticsearch. Most settings from the
+# Elasticsearch output are accepted here as well.
+# Note that the settings should point to your Elasticsearch *monitoring* cluster.
+# Any setting that is not set is automatically inherited from the Elasticsearch
+# output configuration, so if you have the Elasticsearch output configured such
+# that it is pointing to your Elasticsearch monitoring cluster, you can simply
+# uncomment the following line.
+#monitoring.elasticsearch:
+
+# ================================= Migration ==================================
+
+# This allows to enable 6.7 migration aliases
+#migration.6_to_7.enabled: true
diff --git a/ansible/roles/kibana/defaults/main.yml b/ansible/roles/kibana/defaults/main.yml
new file mode 100644
index 0000000..238d276
--- /dev/null
+++ b/ansible/roles/kibana/defaults/main.yml
@@ -0,0 +1,19 @@
+#
+# Licensed to the Apache Software Foundation (ASF) under one or more
+# contributor license agreements.  See the NOTICE file distributed with
+# this work for additional information regarding copyright ownership.
+# The ASF licenses this file to You under the Apache License, Version 2.0
+# (the "License"); you may not use this file except in compliance with
+# the License.  You may obtain a copy of the License at
+#
+#    http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+#
+
+kibana_rpm: kibana-oss-7.8.0-x86_64.rpm
+kibana_checksum: "sha512:2d86268fb951f91a00a981b121e8fa8e77d67671400c180ef81d74d135c24838ea44faad69d76223f0bd8e86ca4ba5e893a75807e84b43287e0a3c323f1fd837"
diff --git a/ansible/roles/kibana/tasks/main.yml b/ansible/roles/kibana/tasks/main.yml
new file mode 100644
index 0000000..6f8f815
--- /dev/null
+++ b/ansible/roles/kibana/tasks/main.yml
@@ -0,0 +1,124 @@
+---
+#
+# Licensed to the Apache Software Foundation (ASF) under one or more
+# contributor license agreements.  See the NOTICE file distributed with
+# this work for additional information regarding copyright ownership.
+# The ASF licenses this file to You under the Apache License, Version 2.0
+# (the "License"); you may not use this file except in compliance with
+# the License.  You may obtain a copy of the License at
+#
+#    http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+#
+
+
+# Installing Kibana
+#
+
+# Add the Kibana yum repo.
+
+- name: "download kibana rpm"
+  get_url:
+  args:
+    url: https://artifacts.elastic.co/downloads/kibana/{{ kibana_rpm }}
+    dest: /tmp/{{ kibana_rpm }}
+    checksum: "{{ kibana_checksum }}"
+    force: no
+
+    #Install kibana
+
+- name: "ensure kibana is installed"
+  become: true
+  yum:
+    name: /tmp/{{ kibana_rpm }}
+    state: present
+
+# Configurations
+
+- name: Updating the config file to allow outside access
+  lineinfile:
+    destfile: /etc/kibana/kibana.yml
+    regexp: "server.host:"
+    line: "server.host: 0.0.0.0"
+  become: true
+
+- name: Defining server port
+  lineinfile:
+    destfile: /etc/kibana/kibana.yml
+    regexp: "server.port:"
+    line: "server.port: 5601"
+  become: true
+
+- name: Defining Elasticsearch URL
+  lineinfile:
+    destfile: /etc/kibana/kibana.yml
+    regexp: "elasticsearch.url:"
+    line: "#elasticsearch.url: \"http://{{ groups['elkserver'][0] }}:9200\""
+  become: true
+
+- name: Defining the Elasticsearch instance URL for queries
+  lineinfile:
+    destfile: /etc/kibana/kibana.yml
+    regexp: "elasticsearch.hosts:"
+    line: "elasticsearch.hosts: [\"http://{{ groups['elkserver'][0] }}:9200\"]"
+  become: true
+
+- name: Defining the output kibana log files
+  lineinfile:
+    destfile: /etc/kibana/kibana.yml
+    regexp: "logging.dest:"
+    line: "logging.dest: stdout"
+  become: true
+
+- name: Defining the default Kibana Application
+  lineinfile:
+    destfile: /etc/kibana/kibana.yml
+    regexp: "kibana.defaultAppId:"
+    line: 'kibana.defaultAppId: "home"'
+  become: true
+
+- name: Defining the default Kibana PID
+  lineinfile:
+    destfile: /etc/kibana/kibana.yml
+    regexp: "#pid.file: /var/run/kibana.pid"
+    line: "pid.file: /var/run/kibana/kibana.pid"
+  become: true
+
+# Make Kibana log directory
+- name: Make Log Directory
+  file:
+    path: /var/log/kibana/
+    state: directory
+  become: true
+
+# Make kibana folder pid
+- name: Make Kibana folder
+  become: true
+  file:
+    path: /var/run/kibana/
+    state: directory
+    recurse: yes
+    mode: 0777
+    owner: kibana
+
+# Make kibana folder pid
+- name: Make Kibana pid File
+  become: true
+  file:
+    path: /var/run/kibana/kibana.pid
+    state: touch
+    mode: 0777
+    owner: kibana
+
+# Starting Kibana
+
+- name: Starting Kibana
+  service:
+    name: kibana
+    state: started
+  become: true
diff --git a/ansible/roles/logstash/defaults/main.yml b/ansible/roles/logstash/defaults/main.yml
new file mode 100644
index 0000000..443317c
--- /dev/null
+++ b/ansible/roles/logstash/defaults/main.yml
@@ -0,0 +1,19 @@
+#
+# Licensed to the Apache Software Foundation (ASF) under one or more
+# contributor license agreements.  See the NOTICE file distributed with
+# this work for additional information regarding copyright ownership.
+# The ASF licenses this file to You under the Apache License, Version 2.0
+# (the "License"); you may not use this file except in compliance with
+# the License.  You may obtain a copy of the License at
+#
+#    http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+#
+
+logstash_rpm: logstash-oss-7.8.0.rpm
+logstash_checksum: "sha512:6640d44c13b6d9243c07ba8fcd25aa9c81f95bcaeefed1d3462c880a64180fce94a966d6c11bf6ebec39c4ab31dec1ec53ff5a6fe3a5e8fd41583db320f9cb3b"
diff --git a/ansible/roles/logstash/tasks/main.yml b/ansible/roles/logstash/tasks/main.yml
new file mode 100644
index 0000000..b7777da
--- /dev/null
+++ b/ansible/roles/logstash/tasks/main.yml
@@ -0,0 +1,78 @@
+---
+#
+# Licensed to the Apache Software Foundation (ASF) under one or more
+# contributor license agreements.  See the NOTICE file distributed with
+# this work for additional information regarding copyright ownership.
+# The ASF licenses this file to You under the Apache License, Version 2.0
+# (the "License"); you may not use this file except in compliance with
+# the License.  You may obtain a copy of the License at
+#
+#    http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+#
+
+
+ #
+ # Installing Logstash
+ #
+
+ # Download Logstash
+- name: "download logstash rpm"
+  get_url:
+  args:
+    url: https://artifacts.elastic.co/downloads/logstash/{{ logstash_rpm }}
+    dest: /tmp/{{ logstash_rpm }}
+    checksum: "{{ logstash_checksum }}"
+    force: no
+
+ # Install Logstash
+- name: "ensure logstash is installed"
+  become: true
+  yum:
+    name: /tmp/{{ logstash_rpm }}
+    state: present
+
+# Update startup.option file with the new home location.
+- name: Update the startup.option file
+  lineinfile:
+    destfile: /etc/logstash/startup.options
+    regexp: 'LS_HOME=/usr/share/logstash'
+    line: 'LS_HOME=/etc/logstash'
+  become: true
+
+# Update logstash config path locatione
+- name: Update logstash config path location
+  lineinfile:
+    destfile: /etc/logstash/logstash.yml
+    regexp: '# path.config:'
+    line: 'path.config: /etc/logstash/conf.d/'
+  become: true
+
+# Make Logstash conf.d  directory
+- name: make logstash conf.d directory
+  file:
+    path: /etc/logstash/conf.d/
+    state: directory
+  become: true
+
+- name: Copy logstash into conf.d folder
+  template:
+     src: ../../logstash/templates/logstash-simple-2.conf
+     dest: /etc/logstash/conf.d/
+  become: true
+
+- name: Install beats input plugin
+  become: true
+  command: /usr/share/logstash/bin/logstash-plugin install logstash-input-beats
+
+# Restart Logstash
+- name: Restarting logstash
+  service:
+    name: logstash
+    state: restarted
+  become: true
diff --git a/ansible/roles/logstash/templates/logstash-simple-2.conf b/ansible/roles/logstash/templates/logstash-simple-2.conf
new file mode 100644
index 0000000..17ca445
--- /dev/null
+++ b/ansible/roles/logstash/templates/logstash-simple-2.conf
@@ -0,0 +1,150 @@
+#
+# Licensed to the Apache Software Foundation (ASF) under one or more
+# contributor license agreements.  See the NOTICE file distributed with
+# this work for additional information regarding copyright ownership.
+# The ASF licenses this file to You under the Apache License, Version 2.0
+# (the "License"); you may not use this file except in compliance with
+# the License.  You may obtain a copy of the License at
+#
+#    http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,e
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+#
+input {
+    beats {
+        port => 5044
+    }
+
+    file {
+        path => "{{ worker_data_dirs[0] }}/logs/accumulo/*.log"
+        type => "accumulo"
+        start_position => "beginning"
+         }
+
+    file {
+        path => "{{ worker_data_dirs[0] }}/logs/hadoop/*.log"
+        type => "hadoop"
+        start_position => "beginning"
+    }
+
+     file {
+        path => "{{ worker_data_dirs[0] }}/logs/zookeeper/*.out"
+        type => "zookeeper"
+        start_position => "beginning"
+    }
+}
+
+filter {
+         if [type] == "accumulo" {
+
+             grok {
+
+        #2020-03-30 14:01:06,322 [gc.GarbageCollectWriteAheadLogs] DEBUG: New tablet servers noticed: [worker3:9997[1000005c5390005], worker1:9997[1000005c5390004], worker2:9997[1000005c5390006]]
+        match => { "message" => "%{TIMESTAMP_ISO8601:TIMESTAMP} \[%{GREEDYDATA:module}\.%{GREEDYDATA:className\] %{LOGLEVEL:level}: %{GREEDYDATA:message}\[%{GREEDYDATA:tservername}:%{GREEDYDATA:tservername}\:%{GREEDYDATA:tservername}\:%{GREEDYDATA:hostname}\]"}
+
+        #2020-06-18 14:27:15,793 [impl.MetricsConfig] INFO : Loaded properties from hadoop-metrics2-accumulo.properties
+        match => { "message" => "%{TIMESTAMP_ISO8601:TIMESTAMP} \[%{GREEDYDATA:module}\.%{GREEDYDATA:className}\] %{LOGLEVEL:level}: %{GREEDYDATA:message}\[%{GREEDYDATA:module}\]"}
+
+        #2020-03-31 04:43:48,553 [gc.GarbageCollectWriteAheadLogs] DEBUG: New tablet servers noticed: []
+        #2020-04-01 01:56:04,271 [gc.GarbageCollectWriteAheadLogs] DEBUG: Tablet servers removed: []
+        #2020-03-30 14:00:35,898 [gc.SimpleGarbageCollector] DEBUG: Got GC ZooKeeper lock
+        #2020-03-30 14:03:39,048 [master.Master] DEBUG: [Root Table]: scan time 0.00 seconds
+        #2020-03-30 14:03:29,331 [master.Master] DEBUG: Finished gathering information from 3 of 3 servers in 0.02 seconds
+        match => { "message" => "%{TIMESTAMP_ISO8601:TIMESTAMP} \[%{GREEDYDATA:module}\.%{GREEDYDATA:className}\] %{LOGLEVEL:level}: %{GREEDYDATA:message}"}
+
+        #2020-04-01 12:56:22,176 [state.ZooTabletStateStore] DEBUG: Returning root tablet state: +r<<@(null,worker1:9997[1000005c5390004],worker1:9997[1000005c5390004])
+        #2020-03-30 14:03:39,048 [master.Master] DEBUG: Root Table location State: +r<<@(null,worker1:9997[1000005c5390004],worker1:9997[1000005c5390004])
+        match => { "message" => "%{TIMESTAMP_ISO8601:TIMESTAMP} \[%{GREEDYDATA:module}\.%{GREEDYDATA:className}\] %{LOGLEVEL:level}: %{GREEDYDATA:message}\(%{GREEDYDATA:tservers}\)"}
+
+        #2020-06-17 14:06:03,898 [sasl.SaslDataTransferClient] INFO : SASL encryption trust check: localHostTrusted = false, remoteHostTrusted = false
+        #2020-06-17 13:40:55,503 [compress.CodecPool] INFO : Got brand-new decompressor [.deflate]
+        #2020-06-17 13:40:19,188 [bcfile.Compression] INFO : Trying to load Lzo codec class: org.apache.hadoop.io.compress.LzoCodec
+        #2020-06-17 13:40:11,052 [lru.LruBlockCacheManager] INFO : Creating INDEX cache with configuration org.apache.accumulo.core.file.blockfile.cache.lru.LruBlockCacheConfiguration@22e49d8, acceptableFactor: 0.85, minFactor: 0.75, singleFactor: 0.25, multiFactor: 0.5, memoryFactor: 0.25, mapLoadFactor: 0.75, mapConcurrencyLevel: 16, useEvictionThread: true
+        #2020-03-30 14:01:06,223 [gc.SimpleGarbageCollector] INFO : Number of successfully deleted data files: 0
+        #2020-06-17 13:40:11,212 [tserver.TabletServer] INFO : Tablet server starting on 0.0.0.0
+        #2020-06-17 13:40:10,742 [server.ServerUtil] INFO : tserver.memory.manager = org.apache.accumulo.server.tabletserver.LargestFirstMemoryManager
+        #2020-06-17 13:40:09,222 [conf.SiteConfiguration] INFO : Found Accumulo configuration on classpath at /home/centos/install/accumulo-2.0.0/conf/accumulo.properties
+        #2020-06-24 14:15:58,727 [compact.CompactRange] INFO : No iterators or compaction strategy
+        match => {"message" => "%{TIMESTAMP_ISO8601:TIMESTAMP} \[%{GREEDYDATA:module}\.%{GREEDYDATA:className}] %{LOGLEVEL:level} : %{GREEDYDATA:message}"}
+
+        #2020-06-24 11:10:00,094 [tracer.TraceServer] INFO : Instance a7f82873-7c32-4510-8560-665523d9b57f
+        match => {"message" => "%{TIMESTAMP_ISO8601:TIMESTAMP} \[%{GREEDYDATA:module}\.%{GREEDYDATA:className}\] %{LOGLEVEL:level} : %{GREEDYDATA:instance} %{GREEDYDATA:instanceID}"}
+
+        #2020-06-24 11:09:59,929 [server.ServerUtil] INFO : instance.volumes = hdfs://leader1:8020/accumulo
+        match => {"message" => "%{TIMESTAMP_ISO8601:TIMESTAMP} \[%{GREEDYDATA:module}\.%{GREEDYDATA:className}\] %{LOGLEVEL:level} : %{GREEDYDATA:instance} %{URI:path}"}
+
+        #2020-06-24 11:09:55,624 [conf.SiteConfiguration] INFO : Found Accumulo configuration on classpath at /home/centos/install/accumulo-2.0.0/conf/accumulo.properties
+        match => {"message" => "%{TIMESTAMP_ISO8601:TIMESTAMP} \[%{GREEDYDATA:module}\.%{GREEDYDATA:className}\] %{LOGLEVEL:level} : %{GREEDYDATA:message} %{PATH:path}"}
+
+        #2020-06-24 15:06:05,196 [zookeeper.DistributedReadWriteLock] INFO : Added lock entry 0 userData 620e830c39101580 lockTpye READ
+        #2020-06-24 14:10:58,054 [tableOps.Utils] INFO : table +r (79bfe74ef98dc6c) locked for read operation: COMPACT
+        #2020-06-24 15:11:06,486 [tableOps.Utils] INFO : namespace +accumulo (24c7ba560088d55b) locked for read operation: COMPACT
+        match => {"message" => "%{TIMESTAMP_ISO8601:TIMESTAMP} \[%{GREEDYDATA:module}\.%{GREEDYDATA:className}\] %{LOGLEVEL:level} : %{GREEDYDATA:message} %{WORD:operation}"}
+
+
+        #2020-06-24 11:10:00,900 [security.SecurityOperation] INFO : Granted table permission READ for user root on the table 1 at the request of user !SYSTEM
+        #2020-06-24 11:10:00,926 [security.SecurityOperation] INFO : Granted table permission WRITE for user root on the table 1 at the request of user !SYSTEM
+        #2020-06-24 11:10:00,935 [security.SecurityOperation] INFO : Granted table permission BULK_IMPORT for user root on the table 1 at the request of user !SYSTEM
+        #2020-06-24 11:10:00,939 [security.SecurityOperation] INFO : Granted table permission ALTER_TABLE for user root on the table 1 at the request of user !SYSTEM
+        #2020-06-24 11:10:00,955 [security.SecurityOperation] INFO : Granted table permission GRANT for user root on the table 1 at the request of user !SYSTEM
+        #2020-06-24 11:10:00,962 [security.SecurityOperation] INFO : Granted table permission DROP_TABLE for user root on the table 1 at the request of user !SYSTEM
+        #2020-06-24 11:10:00,965 [security.SecurityOperation] INFO : Granted table permission GET_SUMMARIES for user root on the table 1 at the request of user !SYSTEM
+        #2020-06-24 11:10:00,989 [zookeeper.DistributedReadWriteLock] INFO : Added lock entry 0 userData 0665dc60a64ce2cd lockType WRITE
+        match => {"message" => "%{TIMESTAMP_ISO8601:TIMESTAMP} \[%{GREEDYDATA:module}\.%{GREEDYDATA:className}\] %{LOGLEVEL:level} : %{GREEDYDATA:message}%{WORD:operation}"}
+
+
+
+
+
+             }
+   }
+    else if [type] == "hadoop"{
+        grok {
+         #2020-03-30 15:01:17,801 INFO org.apache.hadoop.hdfs.StateChange: DIR* completeFile: /accumulo/tables/+r/root_tablet/F000003o.rf_tmp is closed by DFSClient_NONMAPREDUCE_69506301_11
+        match => { "message" => "%{TIMESTAMP_ISO8601}%{SPACE}%{WORD:log level}%{GREEDYDATA:hostname}%{GREEDYDATA:LINK}:%{GREEDYDATA:state}%{LOGLEVEL:level}: %{GREEDYDATA:message}"}
+        match => { "message" => "%{TIMESTAMP_ISO8601}%{SPACE}%{WORD:log level}%{GREEDYDATA:ip}%{GREEDYDATA:LINK}:%{GREEDYDATA:state}%{LOGLEVEL:level}: %{GREEDYDATA:message}"}
+
+        #2020-06-17 13:39:10,434 INFO org.apache.hadoop.yarn.logaggregation.AggregatedLogDeletionService: aggregated log deletion finished.
+        #2020-06-17 13:39:06,483 INFO org.apache.hadoop.mapreduce.v2.hs.JobHistoryServer: registered UNIX signal handlers for [TERM, HUP, INT]
+        #2020-06-17 13:39:07,064 INFO org.apache.hadoop.metrics2.impl.MetricsConfig: Loaded properties from hadoop-metrics2.properties
+        #2020-06-17 13:39:07,147 INFO org.apache.hadoop.metrics2.impl.MetricsSystemImpl: Scheduled Metric snapshot period at 10 second(s).
+        #2020-06-17 13:39:07,703 INFO org.apache.hadoop.mapreduce.v2.jobhistory.JobHistoryUtils: Default file system [hdfs://leader1:8020]
+        match => {"message" => "%{TIMESTAMP_ISO8601:TIMESTAMP} %{LOGLEVEL:level} %{GREEDYDATA:className}: %{GREEDYDATA:message}"}
+    }
+}
+
+    else if [type] == "zookeeper" {
+
+        grok {
+        #2020-06-15 17:15:15,275 [myid:] - INFO  [NIOServerCxn.Factory:0.0.0.0/0.0.0.0:2181:NIOServerCnxnFactory@222] - Accepted socket connection from /172.31.66.109:55402
+        match => { "message" => "%{TIMESTAMP_ISO8601:TIMESTAMP} \[%{GREEDYDATA:ID}:]\ - %{LOGLEVEL:level} \[%{GREEDYDATA:location}\]\ - %{GREEDYDATA:message}" }
+
+        #2020-06-16 14:34:20,639 [myid:] - INFO  [main:NIOServerCnxnFactory@89] - binding to port 0.0.0.0/0.0.0.0:2181
+        #2020-06-16 14:34:20,623 [myid:] - INFO  [main:Environment@100] - Server environment:java.compiler=<NA>
+        match => {"message" => "%{TIMESTAMP_ISO8601:TIMESTAMP} \[%{GREEDYDATA:ID}:]\ - %{LOGLEVEL:level} \[%{GREEDYDATA:method}:%{GREEDYDATA:className}\]\ \- %{GREEDYDATA:message}"}
+
+        #2020-06-16 18:41:28,734 [myid:] - INFO  [ProcessThread(sid:0 cport:2181)::PrepRequestProcessor@653] - Got user-level KeeperException when processing sessionid:0x1000007cddd000b type:create cxid:0xb7ef zxid:0x164a txntype:-1 reqpath:n/a Error Path:/accumulo/4d65522e-62cd-4540-9270-2272a3db2f85/masters/tick Error:KeeperErrorCode = NodeExists for /accumulo/4d65522e-62cd-4540-9270-2272a3db2f85/masters/tick
+        #2020-06-16 14:34:20,622 [myid:] - INFO  [main:Environment@100] - Server environment:java.class.path=/home/centos/install/zookeeper-3.4.14/bin/../zookeeper-server/target/classes:/home/centos/install/zookeeper-3.4.14/bin/../build/classes:/home/centos/install/zookeeper-3.4.14/bin/../zookeeper-server/target/lib/*.jar:/home/centos/install/zookeeper-3.4.14/bin/../build/lib/*.jar:/home/centos/install/zookeeper-3.4.14/bin/../lib/slf4j-log4j12-1.7.25.jar:/home/centos/install/zookeeper-3.4.14/bin/../lib/slf4j-api-1.7.25.jar:/home/centos/install/zookeeper-3.4.14/bin/../lib/netty-3.10.6.Final.jar:/home/centos/install/zookeeper-3.4.14/bin/../lib/log4j-1.2.17.jar:/home/centos/install/zookeeper-3.4.14/bin/../lib/jline-0.9.94.jar:/home/centos/install/zookeeper-3.4.14/bin/../lib/audience-annotations-0.5.0.jar:/home/centos/install/zookeeper-3.4.14/bin/../zookeeper-3.4.14.jar:/home/centos/install/zookeeper-3.4.14/bin/../zookeeper-server/src/main/resources/lib/*.jar:/home/centos/install/zookeeper-3.4.14/bin/../conf:
+        match => {"message" => "%{TIMESTAMP_ISO8601:TIMESTAMP} \[%{GREEDYDATA:ID}:]\ - %{LOGLEVEL:level} \[%{GREEDYDATA:method}:%{GREEDYDATA:className}\]\ \- %{GREEDYDATA:message}\:%{PATH}"}
+
+        #2020-06-17 13:37:17,041 [myid:] - INFO  [main:ZooKeeperServerMain@98] - Starting server
+        match => {"message" => "%{TIMESTAMP_ISO8601:TIMESTAMP} \[%{GREEDYDATA:ID}:]\ - %{LOGLEVEL:level}  \[%{GREEDYDATA:method}:%{GREEDYDATA:className}\] - %{GREEDYDATA:message}"}
+
+        match => {"message" => "%{TIMESTAMP_ISO8601:TIMESTAMP} \[%{GREEDYDATA:ID}:]\ - %{LOGLEVEL:level} \[%{GREEDYDATA:method}:%{GREEDYDATA:className}\]\ \- %{GREEDYDATA:message}\ /%{IPORHOST}"}
+
+
+
+        }
+
+    }
+        }
+output {
+    elasticsearch {
+        hosts => ["http://{{ groups['elkserver'][0] }}:9200"]
+        index => "%{[@metadata][beat]}-%{[@metadata][version]}"
+    }
+}
diff --git a/ansible/wipe.yml b/ansible/wipe.yml
index 8cd5c36..6eadac7 100644
--- a/ansible/wipe.yml
+++ b/ansible/wipe.yml
@@ -29,7 +29,6 @@
     retries: 10
     delay: 3
     until: delete_task is success
-
   - name: "wipe grafana db"
     file: path=/var/lib/grafana/grafana.db state=absent
     register: delete_task
diff --git a/conf/muchos.props.example b/conf/muchos.props.example
index 16eed15..fa1ee7c 100644
--- a/conf/muchos.props.example
+++ b/conf/muchos.props.example
@@ -278,10 +278,11 @@
 # Where:
 #   Hostname = Must be unique.  Will be used for hostname in EC2 or should match hostname on your own cluster
 #   Service = Service to run on node (possible values: zookeeper, namenode, resourcemanager, accumulomaster, client, swarmmanager,
-#             mesosmaster, worker, fluo, metrics, spark). The following services are required: namenode, resourcemanager,
+#             mesosmaster, worker, fluo, metrics, spark, elkserver). The following services are required: namenode, resourcemanager,
 #             accumulomaster, zookeeper & worker
 # If cluster_type=azure, the list of nodes below is auto-generated by the launch action e.g. "muchos launch --cluster accumuloclstr"
 # For the 'azure' cluster type, it is perfectly normal if the auto-generated list of node names is not sequential
+# For viewing logging and statistics with Kibana, the elkserver service must be added to a leader node.
 leader1 = namenode,resourcemanager,accumulomaster,zookeeper
 leader2 = metrics
 worker1 = worker,swarmmanager
diff --git a/contrib/muchos.iml b/contrib/muchos.iml
new file mode 100644
index 0000000..c186099
--- /dev/null
+++ b/contrib/muchos.iml
@@ -0,0 +1,12 @@
+<?xml version="1.0" encoding="UTF-8"?>
+<module org.jetbrains.idea.maven.project.MavenProjectsManager.isMavenModule="true" type="JAVA_MODULE" version="4">
+  <component name="NewModuleRootManager" LANGUAGE_LEVEL="JDK_1_5">
+    <output url="file://$MODULE_DIR$/target/classes" />
+    <output-test url="file://$MODULE_DIR$/target/test-classes" />
+    <content url="file://$MODULE_DIR$">
+      <excludeFolder url="file://$MODULE_DIR$/target" />
+    </content>
+    <orderEntry type="inheritedJdk" />
+    <orderEntry type="sourceFolder" forTests="false" />
+  </component>
+</module>
diff --git a/docs/elk-howto.md b/docs/elk-howto.md
new file mode 100644
index 0000000..7662943
--- /dev/null
+++ b/docs/elk-howto.md
@@ -0,0 +1,23 @@
+Using the ELK Stack service with Fluo Muchos
+--------------------------------------------------------------------
+
+ELK is the acronym for three open source projects: Elasticsearch, Logstash, and Kibana. Elasticsearch is a search and 
+analytics engine. Logstash is a server‑side data processing pipeline that ingests data from multiple sources 
+simultaneously, transforms it, and then sends it to a "stash" like Elasticsearch. Kibana lets users visualize data with 
+charts and graphs in [Elasticsearch](https://www.elastic.co/what-is/elk-stack). 
+
+After the setup has completed, a pipeline will be created for Logstash and Filebeat. To view the dashboard visit the 
+[Kibana](http://localhost:5601/app/kibana#/home) web page. 
+
+For using Elasticsearch data: 
+
+1. Connect to the Elasticsearch index. In the 'Index Pattern' field, enter * and click Next 
+step. 
+2. Select the 'Time Filter' field name from the dropdown. (Ex. @timestamp) Click Create index pattern.
+
+On the menu on the left side corner, select Discover to view the incoming hits and query a specific subset within a selected 
+timeframe. 
+
+For examples on how to query in Kibana please visit the Elastico website [here](https://www.elastic.co/guide/en/beats/packetbeat/current/kibana-queries-filters.html) . 
+
+
diff --git a/lib/muchos/config/base.py b/lib/muchos/config/base.py
index 4849cad..8abd193 100644
--- a/lib/muchos/config/base.py
+++ b/lib/muchos/config/base.py
@@ -44,6 +44,7 @@
     "swarmmanager",
     "journalnode",
     "zkfc",
+    "elkserver",
 ]
 
 OPTIONAL_SERVICES = [
@@ -56,6 +57,7 @@
     "swarmmanager",
     "journalnode",
     "zkfc",
+    "elkserver",
 ]
 
 _HOST_VAR_DEFAULTS = {
diff --git a/lib/muchos/ec2.py b/lib/muchos/ec2.py
index f4f02a2..695975e 100644
--- a/lib/muchos/ec2.py
+++ b/lib/muchos/ec2.py
@@ -116,6 +116,7 @@
         return group_id
 
     def delete_security_group(self):
+
         sg_id = None
         ec2 = boto3.client("ec2")
         try:
diff --git a/lib/muchos/existing.py b/lib/muchos/existing.py
index df3abc0..b519742 100644
--- a/lib/muchos/existing.py
+++ b/lib/muchos/existing.py
@@ -72,6 +72,8 @@
                 print("- import_playbook: mesos.yml", file=site_file)
             if config.has_service("swarmmanager"):
                 print("- import_playbook: docker.yml", file=site_file)
+            if config.has_service("elkserver"):
+                print("- import_playbook: elk.yml", file=site_file)
 
         ansible_conf = path.join(config.deploy_path, "ansible/conf")
         with open(path.join(ansible_conf, "hosts"), "w") as hosts_file:
@@ -122,6 +124,14 @@
                     file=hosts_file,
                 )
 
+            if config.has_service("elkserver"):
+                print(
+                    "\n[elkserver]\n{0}".format(
+                        config.get_service_hostnames("elkserver")[0]
+                    ),
+                    file=hosts_file,
+                )
+
             print("\n[zookeepers]", file=hosts_file)
             for (index, zk_host) in enumerate(
                 config.get_service_hostnames("zookeeper"), start=1